We use cookies and similar tools for site analytics and advertising. By using our site, you agree to this. See our Privacy Policy for details. Do Not Sell or Share My Personal Information
Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Fix uneven cooling or defrost issues with a new temperature sensor. Most DIYers complete this repair in under an hour with basic tools and our video.
I unplugged the fridge and took all the food and shelving out of the freezer and then proceeded to take off the bottom sliding drawer rack on both sides off (4 Phillips head screws). Then took off the light bulb cover and then the light bulb. Then the back wall that covers the coils and tubes that the refrigerant runs through ( 2 screws with hex head). After sliding out the back wall I could see that the entire coil area was frosted and iced up. I took a blow dryer and melted all of it over... Read more
Ice maker not producing ice or stopped working? This ice maker kit restores ice production. Includes full assembly for harvesting and ejecting ice.
Much easier than expected, I was certain it had to be a water line but the solved everything Read more
Dishwasher won't start or run? A faulty door latch prevents cycles from beginning. This latch assembly secures the door and activates switches. 5-10 min fix.
I first did quite a bit of interaction with the AI chat and doing Google searches, as well as entering the diagnostic mode for the dishwasher. (NOTE: Retrieve the technical sheet stored underneath your dishwasher behind the front toe kick panel to learn all about diagnostics!) From this research, I determined three possible issues: (1) the door latch assembly might be malfunctioning, (2) the soap dish actuator might be malfunctioning, and/or (3) the main control board was faulty. The door... Read more
Dishes not drying or staying wet after cycle? This heating element heats water during wash and dries dishes after rinse. DIY-friendly replacement part.
I followed the directions on several websites for repairs. The obvious place to start is the heating coil and thermostat. I checked the continuity of the coil and it was good with a reading of almost zero resistance. Next I read that there is no thermostat controls on my GE dishwasher so I followed another webpage that said the Sensor Turbidity Assembly acts like a thermostat so I replaced that. Wasted effort as that switch sensor was OK. Normally it has a light on when it is working, a... Read more
Replaces broken or worn lower rack carriers and rollers. Installs on both sides of the dishwasher lower rack to restore smooth gliding along tracks.
I was able to find the parts on your website. I was a little worried because there were no photos, but the parts were correct, and it was an easy fix! Read more
This is the flexible rubber or vinyl gasket that lines the opening of your dishwasher tub, creating a watertight seal when the door is closed during a wash cycle. It prevents water from leaking out around the door during operation. Replace it when you notice water pooling on the floor in front of your dishwasher, or when the gasket is visibly torn, stiff, or pulled away from the tub.
Upon taking the door apart it looked like the leak was coming from the vent so I replaced the vent cap, vent seal and the transition piece. I did not have to change the seals. It took me a while to figure out how to get the door apart, but once I did, it was fairly straightforward. Read more
Dishwasher won't drain or leaves standing water? This drain pump kit removes water at cycle end. Common DIY repair taking 15-30 minutes with basic tools.
I viewed youtube videos and followed the instructions on how to determine the cause of the problem. I cleared the lines and poked my fingers in to check for obstructions. But in the end, the drain pump was the problem. The pump came in the mail the next day. The job required the pump and only one of the hose clamps as the original setup has one single ear clamp which can be removed with wire cutters and a standard one which I re-used. There is a wire adapter in the kit that is necessary to... Read more
Dishwasher won't drain or water stays in the tub? A failed drain pump is often the cause. This repair involves removing the dishwasher for access.
Removed two securing screws from side of dishwasher. Pulled out of cabinet careful to not over extend supply/drain/electric connections. Layed unit on side, removed two clamps from each end of drain pump as well as one electrical connection, removed bad pump, replaced connections and clamps, electrical connection. Ran a cycle while out of cabinet to ensure no leaks, replaced unit and screwed back into cabinet. Whole thing took 20 minutes. Read more
The Lower Rack Roller is an OEM replacement part for GE dishwashers. This small but crucial component allows for smooth and effortless movement of the lower dish rack during loading and unloading.
Symptoms of needing to replace the lower rack roller include:
Causes of a faulty lower rack roller can include normal wear and tear over time, exposure to heat or moisture, or physical damage due to impact or mishandling.
This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore dishwasher models.
We ordered one wheel and the case that holds them with great support from The Appliance Parts Pros. Using one original wheel, we snapped the parts together. We used the other three cases as examples and snapped the new case into place. Read more
The Run Capacitor is an OEM part for GE refrigerators. It plays a crucial role in the refrigerator's cooling system by providing the necessary start and run voltage to the compressor. Without a properly functioning run capacitor, your refrigerator may struggle to maintain the desired temperature, leading to spoiled food and inefficient energy use. Causes of a bad run capacitor include electrical surges, wear and tear over time, or overheating due to a malfunctioning refrigerator compressor or poor ventilation. Symptoms of a bad Run Capacitor include:
This OEM GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances.
We replaced the main circuit board and the LED started to work and the condenser fan worked, but all we had were relay clicking sounds, but no cooling. The compressor had become so hot trying to work when the main circuit board was amiss, that it had popped the over temperature sensor on its side. As some one point out, if you remove the PTC+OLP assembly with the capacitor on it, and shake it, you will hear a rattle inside---and that is bad. We ordered a second round of parts from... Read more
Fix a refrigerator that won't cool or has temperature control issues with this main control board. Moderately difficult repair, taking 15-45 minutes.
The indication was that when I tried to use the icemaker or water dispenser, the green LED on the front would dim and the ice maker dispenser wouldn't work. It was intermittent at first, but this indicated it may be a power management issue, in that insufficient voltage was getting to the ice dispenser motor. I unplugged the unit to reset the electronics for about a minute, and when I plugged it back it the compressor would try to turn on (solenoid or relay would click about every two... Read more
Dishwasher detergent dispenser won't open or latch? This module controls soap release during wash cycles. Moderate DIY repair—30 minutes, door removal.
Replacement silverware basket for dishwasher lower rack. Holds and organizes utensils during wash cycles. Order if your basket is cracked or broken.
Replaced Side blaster Read more
Ice maker not filling or water dispenser not working? This refrigerator water inlet valve controls water flow to both. DIY install in 10 minutes.
I replaced the water inlet valve. The toughest part was closing off the feed line while I waited for the valve to be delivered. The needle valve used to install the feed line wouldn't close completely. I ended up fabricating a plug from some parts from the hardware store. The mounting bracket on the new valve was completely different from the original, but it still mounted easily enough. The 1/4" plastic hose fitting was a different type from the original, but the hose fitted into it easily... Read more
This rail assembly allows the upper dish rack to slide smoothly in and out of your dishwasher. It provides the track system that supports the weight of dishes while enabling easy loading and unloading. Replace this part if the upper rack is difficult to slide, wobbles, or has become misaligned.
Replaced the upper rack inner rail assembly. Read more
Replacement door cable and spring kit for dishwashers. Installs on door hinge to provide proper tension and balance. Needed when cables break or springs wear out.
Replaced broken part. Read more