Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
The Flood Switch Assembly is an OEM part for GE dishwashers. This part detects water levels and prevent overfilling by shutting off the water supply if a potential flood condition is detected.
Causes of a bad flood switch assembly can include electrical failures, wear and tear over time, or damage from water exposure.
Symptoms of a bad flood switch assembly include:
This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.
Ordered a new flood switch and activation stem from Aplliance Parts Pros.com. Order was delivered in about 3 days. Installed new switch and stem in about 15 min. Removed front kicker panel with two screws, the switch was just inside the panel secured with two screws. remove the electrical connector, removed screws, replace the two new parts..put the screws back in place and ran the washer...no overflows. Read more
The GE latch handle is an OEM replacement part responsible for allowing the opening and closing of the dishwasher door. Located on the inner door panel, this part ensures that the dishwasher door latches securely when the machine is in operation, preventing any leaks or disruptions in the cleaning process. Additionally, it provides a convenient means for users to open and close the dishwasher, allowing easy access to load and unload dishes. This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. This part fixes the following symptoms
I bought spare part from AppliancePartsPros.com and followed the instructional video. It was easy and saved a few bucks. Read more
Color: blue-gray. It measures about 1-1/2 inches in diameter.
Ordered new part on website which arrived within two days - amazing !!! Truly thought we would be waiting for several weeks for replacement - awesome !!! Read more
Dishwasher rack tine clip used to hold the adjustable tines in place. Color: light gray. Measures about 1-1/2 inches wide by 1 inch deep.
Replaced retainer clips. Read more
Dishwasher overflowing or leaking from the door? A faulty float can cause overfill issues. This float controls water level and prevents flooding.
Thanks to appliancepartspros.com the dishwasher was able to be repaired quickly and under budget. I removed the motor pump assembly and replaced it. I was also able to change out the faulty flood switch and replace the seals to stop the leak. The appliance is once again good as new and ready to run a new load of dishes. Read more
Scr 8-16 b hxw 1.08 ss
I replaced a few key parts that I couldn't clean properly, and were not spinning well in the dishwasher. Afterwards, it worked like new, and the cleaning power returned. Read more
Unscrew the sides and pull the dishwasher out and simple remove the old door hinges and put the new one in. Read more
Ordered parts, waited for them to arrive Took door apart, installed new parts Put door back together shut door (it stayed shut) Washed dishes, opened door (it opened) Dishes were clean (no water on floor) ALL DONE AND IT WORKS Read more
I ordered the part from Appliance Parts Pros; it arrived in three working days. I turned off the power and shut off the water to the dish washer, took off the toe guard and unscrewed the appliance from the countertop. I hoped that I could pull the dish washer out from under the counter without disconnecting the water and wiring as I had seen done in the video. Luckily, I didn't have to disconnect them and with a little effort I was able to pull the dish washer out so I could work on it. ... Read more
The Piston and Nut assembly replaced Check Valve and Body and gasket replaced Read more
I found the manufacturers parts drawing and purchased the parts that were needed.The previous home owner had not only removed from he parts but he had also reversed the direction of the dish rack. The only way I was able to repair it was to figure out how it must function,the rest was easy. Read more
This was not an obvious source of a leak. The Tower Heater Assembly Nut developed a crack over time due to heat exposure. So the leak was gradual slowly getting worse over time. It was a hairline crack that ran down one of the edges of the nut making it hard to see. In talking to a pro he said it isn't a common problem. It is all the way in the back of the bottom of the dishwasher so it is not something you can see without pulling the dishwasher out and running it. The repair itself is easy. I... Read more
Found a service manual that is close enough to my GE dishwasher. Service Manual for GE Dishwasher-EDW4000 was found on the following webpage. http://www.applianceaid.com/pdf/serv-man-EDW4000.pdf Gives enough information to test out the dishwasher. Read it, check out Factory Test Mode. GE should have given this out as a normal User Manual. The usual user manual lack anything to help troubleshoot a problem. Read more
Replaced the parts. Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.