Pdw988on20ss Parts

This rubber grommet provides a protective seal where hoses, wires or components pass through openings, helping prevent chafing and moisture intrusion. Use it to restore a tight fit and reduce wear at the penetration point. What it does:

• Seals and cushions openings to help prevent water leaks and air gaps.
• Protects wiring and hoses from rubbing on sharp metal edges that can cause wear or shorts.
• Reduces vibration and rattling by holding parts securely in place.
• Common symptoms of failure: visible cracking, missing or torn grommet, water dripping near the opening, or rubbing noises.

• Disconnect power to the appliance and turn off water supply before beginning any repair.
• Remove the access panel or boot as needed to reach the opening; press the grommet into the hole until fully seated.
• Inspect surrounding seals, hoses and wiring; replace any damaged components to prevent repeat issues.

This hose clamp secures a washer or dryer hose connection to help prevent leaks and keep hoses firmly attached during operation. It's a simple replacement for worn or loose hose fasteners. What it does:

• Holds inlet or drain hose to the appliance fitting to reduce slipping and leaks
• Restores a tight seal at hose connection points that may be leaking or wobbling
• Keeps hoses positioned correctly during fill and drain cycles
• Useful when clamp is rusted, stretched, or no longer grips reliably

• One hose clamp

• Disconnect power and turn off the water supply before replacing the clamp
• Slide clamp onto hose, position over the fitting, then compress or tighten per clamp type (use pliers or screwdriver as required)
• Inspect the hose and fitting; replace the hose if cracked or damaged
• Test for leaks after restoring power and water

This left-hand arm hinge assembly replaces a worn or damaged door hinge to restore proper door alignment and smooth opening and closing. Designed as the left-side support arm for the appliance door. What it does:

• Supports the left side of the door and secures the door to the cabinet during operation
• Guides smooth door movement and helps prevent sagging or uneven closing
• Stops rubbing, binding, or intermittent contact that can cause noise or poor seal
• Restores proper door fit to maintain normal operation and safety

• Disconnect power to the appliance before starting any repair
• Support the door while removing and installing the hinge to prevent dropping
• Use basic hand tools; verify hinge orientation and alignment before tightening
• Retain or replace mounting hardware if damaged; do not overtighten fasteners

This replacement basket lid is the top cover for the laundry basket assembly, restoring a secure, finished opening so laundry stays contained and the appliance looks and operates as intended. What it does:

• Replaces a cracked, warped, or missing basket lid to restore the basket opening
• Helps keep clothes contained during loading and unloading
• Reduces movement and rubbing that can cause fabric snags or noise
• Restores proper fit and appearance of the basket area

• Disconnect power to the appliance before starting any repair
• Basic hand tools may be required; for disassembly steps
• Handle edges carefully to avoid scratching the finish during install
• If clips or fasteners are damaged, replace them to ensure a secure fit

This keypad is the user-facing button assembly for the oven control panel, letting you send cooking commands and change settings. It restores responsive button control so the range accepts inputs and starts selected functions. What it does:

• Provides the tactile buttons used to enter bake, broil, timer and temperature commands
• Replaces worn or unresponsive keys that won't register presses or skip inputs
• Fixes issues where the control panel won't respond or certain functions won't start
• Works with the control board to relay user selections to the oven electronics

• One keypad (button assembly) as shown

• Disconnect power to the appliance before beginning any service to avoid shock
• Remove control panel trim or bezel as required to access and disconnect the keypad ribbon or connector
• Handle the keypad and ribbon gently to avoid tearing or bending contacts
• Test the keypad operation after reconnecting power and reassembling the panel

Size: 8-18 B 1HW 1/2 S N

This water injector fill hose connects the household water supply to the refrigerator's water/ice system, restoring reliable water flow for dispensing and ice production. Designed as a direct replacement to restore proper fill operation. What it does:

• Delivers water from the inlet to the ice maker/water dispenser assembly.
• Restores proper water fill for ice production and dispenser use when the hose is damaged or leaking.
• Helps stop leaks, sputtering dispensers, or slow/irregular ice fill caused by cracked or blocked tubing.
• Works with the refrigerator's injector/fill pathway to maintain consistent water delivery.

• One water injector fill hose.

• Disconnect power and shut off the water supply before installing.
• Inspect and replace any worn clamps or connectors; tighten fittings to prevent leaks.
• Avoid kinking the hose; route it following the original path to prevent flow restriction.

This rubber grommet cushions and seals appliance components to reduce vibration and prevent wear. It replaces a worn or torn grommet to restore proper fit and quiet operation. What it does:

• Cushions metal-to-metal contact to reduce noise and vibration.
• Helps secure hoses, wiring, or panels where mounted through a hole.
• Prevents chafing and protects components from abrasion.
• Common symptom: rattling, rubbing sounds, or visible rubber deterioration.

• Turn off power to the appliance before starting any repair.
• Remove necessary panels or components to access the damaged grommet; note fastener locations for reassembly.
• Press or push the grommet into the mounting hole until fully seated; some installations may require a flat tool to ease placement.
• If grommet secures wiring or hoses, verify routing and clearance before restoring power.

This inlet transition is a molded connector that fits between the appliance cabinet and the inlet opening to guide incoming air and help maintain a sealed airflow path. It restores proper fit and reduces air leakage where the inlet meets the cabinet. What it does:

• Provides a finished, secure connection at the appliance inlet to direct airflow into the unit
• Helps reduce air leaks that can reduce drying/heating performance or cause airflow imbalance
• Replaces worn, cracked or broken inlet trim that can rattle or vibrate during operation
• Restores correct clearance and sealing where the inlet joins the cabinet

• One inlet transition piece

• Basic hand tools typically required; access the inlet area by removing the back panel or service panel as applicable
• Handle carefully to avoid bending or damaging adjacent trim and mounting tabs
• Disconnect power (and gas if applicable) before beginning service; follow all safety precautions in the appliance manual
• If mounting hardware is missing or damaged, replace with OEM-specified fasteners for secure fit

This kick plate assembly replaces the lower access panel on compatible refrigerators and dishwashers to restore a finished look and protect internal components at the appliance base. It provides a clean, secure cover for the toe-kick area. What it does:

• Covers and protects the lower cabinet opening and components from dirt, debris, and accidental contact
• Restores the appliance's finished appearance at the base for a seamless look
• Helps direct airflow from vents located at the toe-kick area
• Replaces damaged, dented, or missing lower access trim to improve safety and aesthetics

• One kick plate assembly

• Remove power to the appliance before attempting removal or installation
• Typically fastens with clips or a few screws; retain hardware if reusing or replace if damaged
• Handle carefully to avoid scratching painted or plated surfaces during installation

Specs: 8-18 b por 1/2 ss

Specs: 10-16 b rnp 18/25

Size: 8-18 x 7/8 inch.

This is a genuine replacement screw used to secure components and panels on compatible GE appliances. It restores proper fit and prevents rattling or loose parts for safe, reliable operation. What it does:

• Secures panels, brackets, or internal components to maintain proper alignment
• Stops rattling or vibration caused by loose fasteners
• Replaces missing, stripped, or damaged screws to restore safe operation
• Helps maintain seals and clearances by holding parts firmly in place

• Screw

• Disconnect power to the appliance before starting any repair
• Use the correct screwdriver or bit to avoid stripping the head
• Do not overtighten; snug until secure to prevent damage to components
• Keep removed fasteners organized to ensure correct reassembly