Pdwf680rloss Parts

This sump clamp secures the dishwasher's sump connection at the base of the tub, helping maintain a tight, leak-resistant seal. Replacing a weakened or corroded clamp can help stop drips and keep the wash system stable.

• Secures the sump connection so it stays firmly in place
• Applies even clamping force to help maintain a watertight seal
• Helps prevent leaks or puddles beneath the dishwasher
• Typical signs include water leaking from the bottom, a loose connection, or a rusted/broken clamp

• Disconnect power and shut off the water supply before servicing
• Remove the toe-kick and access the sump area; have towels or a pan ready for residual water
• Loosen and remove the old clamp; inspect mating surfaces and the sump seal/gasket and replace if worn
• Position the new clamp squarely and tighten evenly—do not overtighten; run a brief test and check for leaks

This middle conduit carrier secures the dishwasher's water feed tube so it stays aligned as the rack moves. Replacing a cracked or missing carrier helps restore reliable spray delivery and consistent cleaning performance.

• Secures and guides the middle water conduit/feed tube on the rack
• Keeps the conduit aligned with the rear water port for consistent spray
• Helps prevent rack binding or rattling from a loose feed tube
• Helps with weak spray or poor cleaning on the upper rack when the carrier is damaged

• Disconnect power and turn off water before servicing
• Pull the rack forward; release the old carrier's tabs or fastener and detach from the feed tube
• Snap or fasten the new carrier in place; ensure the conduit seats fully at the rear port
• Verify smooth rack travel and run a brief test cycle to check operation

This junction box cover replaces the appliance's electrical access panel to protect wiring and provide a secure entry point for the power cord. It restores a finished, safe electrical connection area and helps prevent exposed wiring. What it does

• Covers and protects the appliance's electrical junction box from dust and accidental contact
• Provides the mounting location and opening for the power cord/strain-relief connection
• Secures wiring and helps keep wire connections contained and stable
• Common symptom: cover cracked, missing, or loose—exposed wires or inability to secure the power cord

• Disconnect power at the breaker or unplug the appliance before servicing electrical parts
• Remove mounting screws from the old cover and replace with the new cover; retain or replace strain relief as needed
• Inspect the cord and wiring while access is open; replace any damaged wiring or strain relief components
• Follow the appliance manufacturer's instructions and local electrical codes for safe installation

Vent driver assembly operates the dryer vent door to manage airflow during operation. Replacing a faulty driver restores proper vent door movement, improving exhaust flow and helping prevent backdrafts. What it does:

• Moves and positions the vent/duct door so exhaust can exit when the appliance runs
• Retracts/closes the vent door when the appliance stops to limit backdrafts
• Common symptoms: vent door won't open or close, reduced exhaust airflow, or visible vent door sticking
• Interfaces with the vent door linkage and the appliance wiring harness to receive control signals

• Disconnect power to the appliance before starting any repair to avoid shock or injury
• Basic hand tools are typically required; support the vent door assembly during removal/installation
• Handle wiring connectors and plastic components carefully to avoid damage
• Follow the appliance's service manual or OEM instructions for exact steps and torque/spec guidance

This clamp secures a hose or small tubing connection on compatible GE laundry appliances to help prevent leaks and keep the connection stable during operation. Durable metal construction resists vibration and wear. What it does:

• Holds a hose or tube firmly to a fitting to reduce leaks and loss of water or airflow
• Stops hose slippage caused by vibration or pressure changes
• Helps restore a tight connection after hose replacement or service
• Simple, low-profile design for use in confined appliance spaces

• Disconnect power and shut off water supply before servicing
• Drain hoses and remove remaining water to avoid spills
• Use the proper screwdriver or nut driver to tighten; do not over-tighten
• Inspect the hose and fitting for wear and replace if damaged before reinstalling the clamp

A small replacement clamp used to secure hoses and small assemblies to prevent leaks or disconnection. Fits the original mounting point and restores a tight seal where the worn clamp no longer holds reliably. What it does:

• Secures a hose or tubing connection to keep water or air from leaking
• Restores proper tension where the original clamp has loosened or corroded
• Helps stop intermittent leaks and prevents hoses from slipping off fittings
• Works in confined appliance areas where a compact clamp is required

• Turn off power and water to the appliance before starting any repair
• Use appropriate hand tools; avoid over-tightening to prevent hose damage
• Dispose of the old clamp and any corroded hardware; inspect surrounding fittings for wear

This 10-32 hex head screw secures appliance panels and components where a small machine screw is required. It provides a durable, threaded fastening point for repair or reassembly. What it does:

• Fastens panels, brackets, and small components using a 10-32 machine thread
• Hex head accepts a 7/16" socket or wrench for positive torque application
• Replaces worn or damaged screws that cause loose or rattling parts
• Compatible with common metal-to-metal and tapped-hole connections

• One 10-32 hex head screw with 7/16" socket head

• Use the correct 7/16" socket or wrench to avoid rounding the head
• Thread engagement should match the appliance's threaded insert; do not force if resistance is felt
• Follow manufacturer service manual for torque specs and installation sequence
• Disconnect power and follow safety procedures before servicing the appliance

Includes 12 screws.

This SCR 8-18 silicon-controlled rectifier replaces the control semiconductor that switches and regulates power to heating or motor circuits in compatible appliances, restoring proper power delivery and control. It's a direct-fit electrical replacement part. What it does

• Acts as a switching device on control boards to allow or block current flow when signaled.
• Regulates power delivered to heating elements or motor circuits to enable proper operation.
• Commonly linked to symptoms like no heat or intermittent heating, motors that won't start, or erratic control-board behavior.
• Helps restore reliable on/off control when a failed SCR is causing open or shorted conditions.

• One SCR 8-18 silicon-controlled rectifier (WD02X10160).

• Always disconnect power before servicing the appliance to avoid shock.
• Handle the part carefully; avoid touching leads and use anti-static precautions if available.
• Inspect surrounding connectors and wiring for damage; replace any corroded terminals.

This left-hand arm hinge assembly replaces a worn or damaged door hinge to restore proper door alignment and smooth opening and closing. Designed as the left-side support arm for the appliance door. What it does:

• Supports the left side of the door and secures the door to the cabinet during operation
• Guides smooth door movement and helps prevent sagging or uneven closing
• Stops rubbing, binding, or intermittent contact that can cause noise or poor seal
• Restores proper door fit to maintain normal operation and safety

• Disconnect power to the appliance before starting any repair
• Support the door while removing and installing the hinge to prevent dropping
• Use basic hand tools; verify hinge orientation and alignment before tightening
• Retain or replace mounting hardware if damaged; do not overtighten fasteners

Size: 8-18 B 1HW 1/2 S N

This rubber grommet cushions and seals appliance components to reduce vibration and prevent wear. It replaces a worn or torn grommet to restore proper fit and quiet operation. What it does:

• Cushions metal-to-metal contact to reduce noise and vibration.
• Helps secure hoses, wiring, or panels where mounted through a hole.
• Prevents chafing and protects components from abrasion.
• Common symptom: rattling, rubbing sounds, or visible rubber deterioration.

• Turn off power to the appliance before starting any repair.
• Remove necessary panels or components to access the damaged grommet; note fastener locations for reassembly.
• Press or push the grommet into the mounting hole until fully seated; some installations may require a flat tool to ease placement.
• If grommet secures wiring or hoses, verify routing and clearance before restoring power.

This keeper latch assembly is the replacement latch that secures the appliance door or drawer in the closed position, restoring a proper seal and reliable closing action. It helps stop doors from popping open and keeps contents contained. What it does:

• Acts as the catch that holds the door or drawer closed
• Restores proper latching when worn, broken, or misaligned
• Helps prevent cold air loss and items shifting during use
• Reduces rattling or intermittent opening caused by a damaged latch

• One keeper latch assembly

• Disconnect power (or unplug) and empty the door/drawer area before starting
• Inspect surrounding trim and strike for damage; replace if needed for proper engagement
• Install by aligning latch with mounting holes and securing fasteners; verify proper catch engagement

This water injector fill hose connects the household water supply to the refrigerator's water/ice system, restoring reliable water flow for dispensing and ice production. Designed as a direct replacement to restore proper fill operation. What it does:

• Delivers water from the inlet to the ice maker/water dispenser assembly.
• Restores proper water fill for ice production and dispenser use when the hose is damaged or leaking.
• Helps stop leaks, sputtering dispensers, or slow/irregular ice fill caused by cracked or blocked tubing.
• Works with the refrigerator's injector/fill pathway to maintain consistent water delivery.

• One water injector fill hose.

• Disconnect power and shut off the water supply before installing.
• Inspect and replace any worn clamps or connectors; tighten fittings to prevent leaks.
• Avoid kinking the hose; route it following the original path to prevent flow restriction.

Color: White. For gray order WD35X21041. Roller only. Does not include axle. For axle order WD35X21041. Updated by the manufacturer. May be wider than original.

This is a genuine replacement screw used to secure components and panels on compatible GE appliances. It restores proper fit and prevents rattling or loose parts for safe, reliable operation. What it does:

• Secures panels, brackets, or internal components to maintain proper alignment
• Stops rattling or vibration caused by loose fasteners
• Replaces missing, stripped, or damaged screws to restore safe operation
• Helps maintain seals and clearances by holding parts firmly in place

• Screw

• Disconnect power to the appliance before starting any repair
• Use the correct screwdriver or bit to avoid stripping the head
• Do not overtighten; snug until secure to prevent damage to components
• Keep removed fasteners organized to ensure correct reassembly