Pdwt480vss Parts

Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.

Genuine Ge part

Tine Clip

4.9 (19)

By: Ge

Part Number: WD12X10116

Dishwasher rack tine clip. Used to hold the tines in place within the rack. Color: gray. Measures about 1 inch wide by 1 inch high by 1-1/2 inches deep.

Do-It-Yourself Stories from Customers like You The dishwasher would not drain sometimes Thomas W. • Oceanside , CA • October 02, 2016

I replaced the pump drain assembly. The flapper valve was included in the assembly, so I did not need to order that. On previous repairs, the old drain hose was tricky to reinstall, so I replaced it and the hose clamp.The silverware basket had holes in the bottom and required replacement. I had some broken tine clips. Read more

Genuine Ge part

Flood Switch Seal (Dishwasher)

4.8 (4)

By: Ge

Part Number: WD01X10264

This dishwasher flood switch seal sits around the flood/leak switch to create a watertight barrier at the switch opening. Replacing a cracked or flattened seal helps stop under-unit drips and keeps leak detection working properly.

Forms a watertight seal where the flood switch mounts
Helps prevent water from entering the base pan
Common signs include water under the unit or visible wear on the old seal

What's included: One flood switch seal. Install notes:

Disconnect power and shut off the water supply before servicing
Remove the toe-kick; pull the unit forward if needed to access the flood switch
Release the flood switch, remove the old seal, and seat the new seal evenly—do not overtighten
Reassemble and run a short fill/rinse while checking closely for leaks

Do-It-Yourself Stories from Customers like You The motor pump assembly seized up and was inoperable the flood sensor was leaking and overflowing through the door Tim D. • Knoxville , TN • December 06, 2018

Thanks to appliancepartspros.com the dishwasher was able to be repaired quickly and under budget. I removed the motor pump assembly and replaced it. I was also able to change out the faulty flood switch and replace the seals to stop the leak. The appliance is once again good as new and ready to run a new load of dishes. Read more

Genuine Ge part

Dishwasher Float

5.0 (4)

By: Ge

Part Number: WD12X10047

Dishwasher overflowing or leaking from the door? A faulty float can cause overfill issues. This float controls water level and prevents flooding.

Genuine Ge part

Dishwasher Vent Cover

5.0 (3)

By: Ge

Part Number: WD12X10127

Replaces a cracked, broken, or missing dishwasher vent cover that mounts on the inner door panel. Shields the exhaust opening and directs airflow.

Do-It-Yourself Stories from Customers like You Had a leak around the vent cover Richard M. • Albuquerque , NM • January 10, 2016

The 4 screws that hold the vent cover in place also hold the assembly inside the door that has the heater motor and other items. The four screws go through the assembly inside the door, through the door and into 4 plastic legs on the vent cover. Two of the legs on the vent cover were broken and therefore the vent cover and the assembly inside the door were not being held tight against the door. The water was leaking in that area. Read more

Genuine Ge part

Middle Spray Arm Bracket

5.0 (2)

By: Ge

Part Number: WD12X10405

This middle spray arm bracket secures the mid-level spray arm to the upper rack, keeping it centered and aligned so it spins freely and delivers even spray coverage for reliable cleaning performance.

Supports and stabilizes the middle spray arm beneath the upper rack
Maintains proper clearance for smooth rotation and spray pattern
Replace if cracked, warped, or worn
Common symptoms: middle arm falls off or won't spin, wobbles, scraping noises, or poor cleaning on the upper rack

What's included: 1 middle spray arm bracket Installation notes:

Disconnect power to the dishwasher before servicing
Slide out the upper rack; release tabs or fasteners to remove the old bracket
Transfer the spray arm to the new bracket and snap or secure it in place
Spin the arm by hand to ensure free rotation before running a cycle

Do-It-Yourself Stories from Customers like You Dishwasher was not cleaning dishes like before when new found crack in upper basket water line feed David G. • Pell City , AL • February 05, 2016

Removed upper basket out of dishwasher by removing slide arm stops. Turned basket upside down and removed broken parts. Took 5 minutes to take apart and put back together. Read more

Genuine Ge part

Dishwasher Float Dome

5.0 (1)

By: Ge

Part Number: WD12X10119

Fix dishwasher overfilling or not filling properly by replacing the float dome. Snaps onto the float assembly to control water level. DIY repair.

Do-It-Yourself Stories from Customers like You Float in dishwasher Michael M. • Bronx , NY • September 12, 2021

Exact GE part, so perfect. Thank you! Read more

Genuine Ge part

Locknut

5.0 (1)

By: Ge

Part Number: WD12X10135

Do-It-Yourself Stories from Customers like You Leaking dishwasher. Jacob W. • Newberg , OR • April 07, 2020

I found the schematics on your site and took my best guess at the individual components that I should replace, related to the flood switch. I guessed correctly. Read more

Genuine Ge part

Grommet Heater

5.0 (2)

By: Ge

Part Number: WD01X10094

Do-It-Yourself Stories from Customers like You Leaking water Stephen M. • Vineland , NJ • April 19, 2021

This was not an obvious source of a leak. The Tower Heater Assembly Nut developed a crack over time due to heat exposure. So the leak was gradual slowly getting worse over time. It was a hairline crack that ran down one of the edges of the nut making it hard to see. In talking to a pro he said it isn't a common problem. It is all the way in the back of the bottom of the dishwasher so it is not something you can see without pulling the dishwasher out and running it. The repair itself is easy. I... Read more

Genuine Ge part

Water Inlet Nut

5.0 (1)

By: Ge

Part Number: WD01X10220

Do-It-Yourself Stories from Customers like You Leaking water on the left side facing unit Gary S. • Lutherville , MD • April 05, 2020

Remove the unit. Unscrewed filler cup. Put on new part. FIXED PROBLEM. Read more

Genuine Ge part

Door Spring

By: Ge

Part Number: WD03X10022

The front door of a dishwasher is operated in part by the use of door springs. There are typically two door springs on most models. The door spring helps the user open and shut the door efficiently. If the door springs are worn out or broken, a replacement part is required.A visual inspection will determine if a door spring is missing, damaged, or worn out. If the dishwasher door no longer opens and closes smoothly, it's an indication that a repair is required. Replacing a dishwasher door spring is a straightforward process. Locate the existing springs and remove them. Line up the new door springs and hook the ends into place. Wear gloves for protection. Disconnect the dishwasher before starting the replacement.This door spring is an authentic OEM replacement part. It is sold individually. The component is made of durable, high-quality metal materials. The replacement door spring comes sourced directly from the manufacturer. The door spring is fitting for several different models of dishwashers. The part can be installed in General Electric, Hotpoint, and RCA devices.

Genuine Ge part

Spray Arm Water Supply Tube

5.0 (5)

By: Ge

Part Number: WD12X10113

Do-It-Yourself Stories from Customers like You The dishwasher was severely covered with calcium and lime the glassware and silverware were coming out with a lot of spotting Peter G. • Niceville , FL • October 18, 2016

I used lime away, vinegar, finish washer cleaner none of them worked. Finally just use Brillo on the entire cabinet interior. It came out very clean. Only needed very light scrubbing. Then replaced the severely corroded filters Riser tube and upper jet which was not turning. After this the upper arm turned perfectly silverware and glassware and silverware came out rinse very clean. Will do preventative maintenance in the future. Dishwasher was about 5 years old GE Profile high-end Read more

Genuine Ge part

Turbidity Sensor (Washer)

By: Ge

Part Number: WD21X10272

This turbidity sensor monitors wash water clarity so the machine can adjust wash cycles and rinse times for cleaner results and efficient water use. It replaces a failed or inconsistent turbidity reading to restore proper load sensing. What it does:

Detects soil level/turbidity in wash water so the washer adapts cycle length and rinse actions
Helps prevent over- or under-washing by feeding water-quality signals to the control board
Commonly replaces units that cause long or short cycles, poor cleaning, or error codes related to wash sensing

What's included: One turbidity sensor Install notes:

Disconnect power before replacing to avoid shock or damage to electronics
Handle the sensor and connectors carefully; avoid contaminating sensing surfaces
Verify connector orientation and secure mounting; test a short cycle after installation

Genuine Ge part

Dishwasher Heating Element

4.9 (8)

By: Ge

Part Number: WD05X10010

This part fixes the following symptoms

Not drying dishes properly

Do-It-Yourself Stories from Customers like You Flashing selection light: i think it fixed the problem by changing out the heating element Michael A. • Henderson , NV • April 19, 2015

Found a service manual that is close enough to my GE dishwasher. Service Manual for GE Dishwasher-EDW4000 was found on the following webpage. http://www.applianceaid.com/pdf/serv-man-EDW4000.pdf Gives enough information to test out the dishwasher. Read it, check out Factory Test Mode. GE should have given this out as a normal User Manual. The usual user manual lack anything to help troubleshoot a problem. Read more

Genuine Ge part

Lower Spray Arm Bearing

4.9 (15)

By: Ge

Part Number: WD01X10107

This is a genuine OEM replacement lower spray arm bearing sourced directly from the manufacturer for use in dishwashers. The lower spray arm spins to distribute water to the dishes during the wash cycle. Thus spray arm bearing supports the spray arm and lessens the friction, which allows it to spin more easily. If the dishes are not clean after the wash and rinse cycle, or the arm is making loud noises, the spin arm bearing may need to be replaced. This bearing is a small metal part that may wear over time. If the bearing is distorted or damaged, the arm will not sit level, and spinning may be very loud, or it may not spin. The spray arm bearing should be replaced. Turn off the breaker or disconnect the power to the dishwasher. Open the dishwasher and pull the bottom rack out. Turn the lower spray arm counterclockwise to remove it. Use a telescoping magnet to pull the bearing up from the hole in the middle. Install the new bearing and reinstall the spray arm. Put the dishrack back inside and reconnect the power.This lower spray arm bearing is a gray metal part that is sold individually. It is designed for use in dishwashers designed by General Electric and Hotpoint.

This part fixes the following symptoms

Noisy

Do-It-Yourself Stories from Customers like You Leaking water onto the floor John G. • Canmer , KY • May 28, 2015

The main conduit was broken and the pump connector had a hole in it. The pump also was showing signs of leaking. I completely disassembled the dishwasher cleaned everything and reassembled. The repair videos are a big help. Thank you. Read more