Pfe29psdss Parts

Port Gasket forms a watertight seal around the refrigerator dispenser port to prevent leaks and moisture intrusion. Installing a fresh gasket restores proper sealing and helps stop dispenser drips and water pooling. What it does:

• Seals the dispenser/port opening to prevent water from leaking at the door area.
• Helps stop visible dripping or pooling near the dispenser and reduces moisture buildup.
• Replaces worn, cracked, flattened, or missing gaskets that allow leaks or drafts.
• Restores a proper seal so the dispenser operates without water escaping around the port.

• Disconnect power (and shut off the water supply if working near the dispenser) before beginning work.
• Remove the old gasket and thoroughly clean mating surfaces to ensure a full seal.
• Press the new gasket evenly into the port opening, making sure it seats all the way around.
• After installation, restore power/water and run a small dispense test to confirm no leaks.

Gallon bin divider for the refrigerator door that keeps gallon jugs and tall containers upright and organized. Durable replacement restores proper separation in the door bin so items stay secure and reduce shifting. What it does:

• Separates the door's gallon bin to keep bottles and tall containers upright and prevent tipping.
• Reduces sliding and shifting when the door opens or closes.
• Replaces cracked, broken, or missing dividers that allow containers to tilt or fall.
• Fits into the existing door bin track to restore original bin organization.

• Remove items from the door bin before installing; some bins may need to be lifted out for access.
• Snap or slide the divider into the bin's existing slot or track—no special tools typically required.
• Inspect the bin and track for cracks or damage; damaged bins may prevent a secure fit.

This SCR is a solid-state switching module that controls on/off power flow in select appliance circuits. Replacing a failed SCR helps stop intermittent operation and restores reliable switching for affected motors or heating elements. What it does:

• Regulates electrical switching in the control circuit to turn motors or heaters on and off.
• Used where a solid-state switch is required for smooth, repeatable control.
• Symptoms of a failing SCR: appliance won't start, runs intermittently, hums without operating, or a controlled circuit does not respond.
• Restores proper switching when the original SCR is shorted, open, or erratic.

• Disconnect power to the appliance before beginning service; follow lockout/tagout procedures.
• Handle as an electronic component—avoid static discharge and protect the spade terminals from bending or contamination.
• Ensure correct orientation and secure mounting; reconnect wiring exactly as shown on the appliance wiring diagram.

A replacement crossbar pinion that engages the ice-maker ejector crossbar to advance the harvest cycle. Installs on the ice maker drive assembly to restore proper rotation of the ejector and help clear ice from the mold. What it does:

• Drives the ice-maker crossbar/ejector during the harvest cycle so ice cubes are pushed out.
• Transfers rotation from the ice-maker motor/cam to the ejector crossbar.
• Common symptoms: ice maker won't advance or eject cubes, loud grinding or clicking from the ice bin, or visible broken/missing gear teeth.
• Restoring a worn or broken pinion can stop jamming and allow normal harvest cycles to resume.

• Disconnect power to the appliance before servicing; shut off the water if removing the ice maker assembly.
• Remove the ice maker per the manufacturer's instructions to access the pinion; handle plastic gears carefully to avoid damage.
• Inspect mating gears and the ejector crossbar for wear or damage and replace any damaged components to prevent repeat failure.
• After installation, restore power and run a test harvest cycle to ensure proper operation.

This ice maker feeler arm senses the ice level in the bin and controls when the icemaker starts and stops. Replacing a bent, missing, or stuck arm restores correct shutoff and helps prevent overfilling or no-ice conditions.

• Monitors the ice bucket level and raises/lowers to start or stop ice production
• Shuts the icemaker off when the bin is full; allows production when lowered
• Common symptoms: ice maker won't stop making ice/overflows, no ice when the arm is stuck up, loose or missing arm
• Restores proper on/off control of the icemaker cycle

• Disconnect power and turn off the water supply before servicing
• Remove the ice bin and, the icemaker assembly to access the arm
• Transfer any reusable hardware; seat the arm fully in its pivot points so it moves freely
• Restore power, lower the arm to the On position, and allow time for the icemaker to cycle

8-18 CA HX 1/2 S

This felt tape is used in the refrigerator to cushion and seal mating parts, helping reduce vibration/squeaks and prevent chafing or small air leaks. Replace worn or missing tape to restore a quieter, more secure fit of covers and ducts.

• Provides a soft barrier between panels, ducts, or rails to minimize vibration and squeaks
• Helps seal minor gaps to support proper airflow paths
• Replaces deteriorated, compressed, or missing original felt tape
• Common symptoms include rattling/buzzing from covers or panels, squeaking drawers, or a loose cover that won't seat correctly

• Disconnect power to the refrigerator before servicing
• Note the original tape's location; remove the old tape and any residue
• Clean and dry surfaces thoroughly; apply the new tape in the same position (peel liner if adhesive-backed)
• Do not block vents, sensors, or fastener holes when applying

This replacement meat pan assembly provides a removable, easy-to-clean pan for storing deli and meat items and for catching drips to help keep the refrigerator interior sanitary and organized. What it does

• Holds deli/meat items and helps contain juices to reduce mess and cross-contamination.
• Replaces a cracked, warped, missing, or leaking meat pan that no longer seals or sits correctly.
• Restores proper fit on the shelf track so the pan slides in and out smoothly.
• Helps reduce odors and makes cleanup faster by keeping spills contained.

• Remove food and shelves from the area before installing to avoid spills.
• Slide the pan into the existing shelf track until it seats; most installs require no tools.
• Inspect supporting rails or brackets for damage and replace if worn to ensure proper fit.
• Follow basic food-safety cleaning before first use; disconnect power to appliances only if required per your model's service instructions.

This hinge-mounted refrigerator door stop limits how far the door swings open, protecting the cabinet and nearby walls from impact. Replace a cracked or missing stop to restore a controlled, factory door swing and prevent overextension.

• Mounts on the door hinge to control the door's opening range
• Helps prevent the door or handle from striking adjacent walls or cabinets
• Common symptoms: door opens past its normal range, broken/missing stop, visible wear at the hinge stop
• Often needed after an impact or when the original stop cracks from fatigue

• Disconnect power; turn off water to the door if applicable
• Support the door before loosening hinge fasteners; door removal may be required on some models
• Install the stop on the correct hinge location (right or left as required) and tighten hardware securely
• Verify door swing and clearance before fully loading shelves

This evaporator cover is the molded housing that protects the freezer evaporator and helps direct airflow for proper defrosting and cooling performance. It replaces a damaged or cracked cover to restore proper airflow management. What it does:

• Shields the evaporator coil and fan area from debris and direct contact
• Helps direct airflow through the evaporator for even cooling
• Supports proper defrost drainage and reduces ice buildup when functioning correctly
• Can reduce unusual noises caused by loose or broken cover components

• Requires access to the freezer interior and removal of shelves/panels; follow manufacturer service manual for disassembly steps
• Power off and unplug appliance before starting work and allow any accumulated frost to thaw safely
• Inspect associated gaskets, fasteners, and the evaporator fan while replacing the cover; replace any damaged parts as needed

A #8-18 x 9/16-inch hex washer head screw used to secure panels and components in appliances. Provides a proper fit for fast, reliable fastening when replacing missing, damaged, or stripped screws. What it does:

• Secures panels, brackets, and trim to keep components aligned and stable.
• Restores proper fastening when threads are stripped, the original screw is missing, or a head is damaged.
• Helps stop rattling or loose parts caused by worn or broken fasteners.
• Fits applications requiring a #8-18 thread with a 9/16" length and hex washer head style.

• Verify thread size, head style, and length before installation.
• Use the correct hex driver or socket to avoid cam-out or head damage.
• Do not overtighten; snug until secure to avoid stripping threads or deforming parts.
• Disconnect power and follow appliance-specific safety steps.

This is a replacement round-head 10-32 x .353 screw used to fasten appliance panels and internal components. It restores secure mounting and helps stop rattling or loose parts caused by missing or worn fasteners. What it does:

• Secures panels, brackets, or small assemblies where a 10-32 machine screw is specified
• Stops movement and vibration that can cause noise or misalignment
• Replaces missing, stripped, or corroded fasteners to restore proper fit
• Matches the original fastener size and head style for correct clearance

• One 10-32 x .353 round-head screw

• Use the matching driver (typically a Phillips or slotted driver as required by the head) and avoid over-torque to prevent stripping
• Disconnect power and follow safety procedures when accessing internal components
• If other fasteners appear damaged or corroded, inspect and replace as needed

8-18 hi/lo 5/8

This 8-18 x 9/16 screw is a short sheet-metal fastener used to secure panels, trim and small components on appliances. It replaces missing or stripped screws to restore proper fit and reduce noise from loose parts. What it does

• Secures appliance panels, brackets and trim to prevent movement and rattling
• Holds small components in correct alignment for reliable operation
• Replaces lost, worn or stripped screws that cause gaps or loose fittings
• Common symptom link: fixes rattling panels, loose trim, or parts that shift during use

• One 8-18 x 9/16 screw

• Use the correct 8-18 driver bit and hand or low-torque power driver to avoid stripping
• Do not overtighten; snug until secure to prevent thread damage or panel deformation
• Turn power off/unplug appliance when installing near electrical components
• Keep extra screws on hand—hardware often comes in single quantities

This silicon controlled rectifier (SCR) is a replacement power-control semiconductor used to regulate current in appliance power circuits, helping restore proper operation of heating and motor circuits that rely on solid-state switching. What it does:

• Acts as a switch to control and modulate electrical current in the appliance power path
• Enables regulated power delivery to heating elements or motor circuits when driven by the control board
• Commonly replaced when the appliance shows intermittent power, no heat, or erratic on/off behavior in the affected circuit
• Works as a direct replacement for the OEM SCR with identical mounting and electrical fit when specified by part number

• Disconnect power to the appliance before starting any repair to avoid shock or damage
• Observe basic ESD precautions when handling the SCR and avoid touching semiconductor leads

The Manifold & Plug Assembly is an OEM part for GE refrigerators. This assembly is responsible for housing the water filter and ensuring a proper connection to the water supply.

A bad filter manifold & plug assembly can be caused by normal wear and tear, clogging or blockage in the filter, or damage due to mishandling or impact. If you notice a decrease in water flow or water pressure, a strange taste or odor in your drinking water, or if the filter does not fit securely in the assembly, it may indicate a problem with the filter manifold & plug assembly.

Symptoms of a bad filter manifold & plug assembly include:

• Reduced water flow or water pressure
• Strange taste or odor in the drinking water
• Leaks or drips around the filter assembly
• Difficulty in installing or removing the filter

Replace your faulty manifold & plug assembly with this genuine OEM part to ensure clean and filtered water. This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances.