Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Protective grille cover that mounts over the temperature sensor in your refrigerator. Replace if cracked, broken, or missing to properly shield the sensor.
Common theme on the blogs was thermistors and or defrost heater/thermostat. Ran self-diagnostics which turned on defrost heater which was fine. All five thermistors indicated ok on diagnostic also, but I read more than one time "replace the thermistors no matter what if your FF section isn't cooling". So I ordered all five thermistors and defrost limiter thermostat. Received all in 48 hours (great shipping service), took me about three hours to replace all thermistors and thermostat just as... Read more
Protective enclosure for the ice crusher mechanism in your refrigerator's dispenser. Replace if cracked, broken, or damaged from ice jams or wear.
I ordered a replacement auger from AppliancePartsPros.com. Upon receipt of the new auger, I watched the repair video and took the ice crusher apart. I found several other parts that needed to be replaced as well. Once All the parts were received, I again watched the video. The video was not specific enough to show how to reassemble the ice crusher blades and the two types of washers. I found another video on YouTube that walked me through specific details of assembly and everything went... Read more
Ice scattering everywhere? This deflector guides cubes or crushed ice down the chute into your glass. Replaces cracked or missing deflectors in 30 minutes.
When we inspected the first time we found that Plactic had broken from the spiral part that for wards the ice. Also there were cracks in two places of other parts. There was a hole in the bottom of the bin. The new spiral was assembled and two new parts were replaced with help from the video and the diagram and the unit worked well. Two months later, ice maker would not forward any ice though the bin was full. We emptied the bin sand have ordered a new part or two in hopes that they will... Read more
Replaces broken or cracked refrigerator door stop. Installs on door to limit swing range and prevent cabinet damage. Needed when missing or worn.
Replaced upper and lower thimble's, lever arm, cam closure. Door stop was not the problem, but ordered it and replaced it too. The door of course has to come off, remove the top hinge, and lift it away. Lubricated moving parts with silicone spray. Be sure and put the door back in the open position, so the lever arm and cam closure can properly interact, then close the door. Remove the plastic grate at the bottom to get at the lever arm. Presto. Problem gone. Don't put excessive weight... Read more
Bushing that lines the upper hinge pin on refrigerator doors. Replace if cracked, worn, or missing to restore smooth door swing and proper alignment.
Replaces the worn or cracked hinge bushing at the bottom of your refrigerator door. Installs on the lower hinge pin for smooth door movement and alignment.
Replacement glass insert for refrigerator crisper pan cover. Restores the flat shelf surface above drawers. Replace if cracked, broken, or shattered.
Replaced glass. Read more
This armature kit is the moving plunger and linkage operated by the dispenser solenoid. It opens and closes the ice chute door during dispensing and helps it seal when idle to reduce frost and warm-air leaks.
Replaced the water supply valve...boom! Read more
Replaces the damaged or missing edge trim on your freezer shelf. Snaps onto the shelf frame to provide a finished lip and restore its original appearance.
Replaced with new parts. Read more
Carries defrost water from evaporator to drain pan in your refrigerator. Replace if cracked, brittle, clogged, or missing to prevent leaks and puddles.
Replaced the drain pan below the evaporator coil (it was rusted to the point had a hole in it) and decided to replace both drain tubes since I had to open up the back panel. The video on the website was very helpful. Thanks!! Read more
The recess door retainer secures the dispenser's ice chute flapper in the refrigerator door. Replacing a cracked or missing retainer restores proper flapper pivot and sealing to help reduce frost buildup and air leaks around the dispenser.
I replaced the solenoid, door, spring and bucket. The bucket cracked from ice freezing inside it. Ice froze inside the bucket because the solenoid stopped pulling the door closed which allowed hot humid air into the freezer. While I was in there I replaced the dispenser door, spring and crank because they are cheap and the old ones were moldy. The mold is most likely from the door not closing and causing condensation on the parts as well. Read more
Fix a light that won't turn on or flickers in your refrigerator. This E12 socket replacement is straightforward with our step-by-step video guide.
When diagnosing the problem, I discovered that the ice door was not properly sealing and that the solenoid had appeared to rust/corrode forcing the door open. I replaced most of the ice dispenser internals (solenoid, crank, door, and spring) following the video. The door will now open when dispensing ice (which it does!), and will oddly stay open for a few seconds once I am finished, but does seal properly and the chute/container no longer frosts over. Read more
Protects the freezer light bulb from damage while maintaining visibility. Replace if cracked, yellowed, or broken. Confirm fit with your model number.
Replace solenoid, flapper door and recess spring. Really only needed solenoid, but other parts were so inexpensive and I knew I would already be in there. Read more
Ice won't dispense or drive spins freely? This auger drive coupler connects the motor to the ice bucket. Moderately difficult repair with basic tools.
The auger in ice bucket was frozen and locked in place (some how liquid water must have spilled inside and froze the shaft and bushing). When the motor was activated to deliver ice, the jam caused the motor shaft to strip the threads. With the threads stripped, there is no way (that I could find) to get the drive auger off of the shaft (btw, it is left-hand threaded). Apparently the Drive Auger is made of stainless steel - a harder metal then the motor shaft. To repair it, I removed the... Read more
Replacement chill pan drawer that slides into refrigerator shelf rails. Needed when original pan is cracked, broken, melted, or missing. Exact fit.
The replacement drawer you sent was a perfect match - it slid right into the rails on the shelf as if I was simply putting back the original drawer after washing it. Read more
Fixed freezer shelf for side-by-side refrigerators. Replace a cracked, broken, or missing shelf to restore organized storage and spacing.
Ordered replacement shelves Read more