Need Help?
Call or text
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Protective enclosure for the ice crusher mechanism in your refrigerator's dispenser. Replace if cracked, broken, or damaged from ice jams or wear.
I ordered a replacement auger from AppliancePartsPros.com. Upon receipt of the new auger, I watched the repair video and took the ice crusher apart. I found several other parts that needed to be replaced as well. Once All the parts were received, I again watched the video. The video was not specific enough to show how to reassemble the ice crusher blades and the two types of washers. I found another video on YouTube that walked me through specific details of assembly and everything went... Read more
Ice scattering everywhere? This deflector guides cubes or crushed ice down the chute into your glass. Replaces cracked or missing deflectors in 30 minutes.
When we inspected the first time we found that Plactic had broken from the spiral part that for wards the ice. Also there were cracks in two places of other parts. There was a hole in the bottom of the bin. The new spiral was assembled and two new parts were replaced with help from the video and the diagram and the unit worked well. Two months later, ice maker would not forward any ice though the bin was full. We emptied the bin sand have ordered a new part or two in hopes that they will... Read more
Bushing that lines the upper hinge pin on refrigerator doors. Replace if cracked, worn, or missing to restore smooth door swing and proper alignment.
Replaced upper and lower thimble's, lever arm, cam closure. Door stop was not the problem, but ordered it and replaced it too. The door of course has to come off, remove the top hinge, and lift it away. Lubricated moving parts with silicone spray. Be sure and put the door back in the open position, so the lever arm and cam closure can properly interact, then close the door. Remove the plastic grate at the bottom to get at the lever arm. Presto. Problem gone. Don't put excessive weight... Read more
Replaces a cracked, broken, or worn ice dispenser lever on your refrigerator. This paddle activates the dispensing mechanism for water and ice.
I bought two parts. The dispenser housing shield and the funnel ice dispenser. I watched the short video on how to put it back together and I was done in just a matter of minutes. The video was such a big help. I forgot how the spring went on and was able to watch the video and put it back together in just a matter of minutes. I know I must have saved a couple of hundred dollars on a service call. Read more
Replaces the worn or cracked hinge bushing at the bottom of your refrigerator door. Installs on the lower hinge pin for smooth door movement and alignment.
Replaces the damaged or missing edge trim on your freezer shelf. Snaps onto the shelf frame to provide a finished lip and restore its original appearance.
Replaced with new parts. Read more
This armature kit is the moving plunger and linkage operated by the dispenser solenoid. It opens and closes the ice chute door during dispensing and helps it seal when idle to reduce frost and warm-air leaks.
Replaced the water supply valve...boom! Read more
The recess door retainer secures the dispenser's ice chute flapper in the refrigerator door. Replacing a cracked or missing retainer restores proper flapper pivot and sealing to help reduce frost buildup and air leaks around the dispenser.
Replaced springs, flapper assembly and ice door retainer as described in videos and it was easy. So far so good..water dispenses. Read more
Plastic water line that runs from the water valve to the icemaker fill tube. Replace if cracked, brittle, broken, or leaking at connection points.
Thanks to the AppliancePartsPro, I ordered it online and received it quickly. I even used the step by step directions on how to replace the tube from the AppliancePartsPro website. Just be very careful and review the instructions first. Couple of important things: 1. Take a picture of the existing wiring and tubes before you take them apart. 2. *if* you remove the wires ( red and white plugs) from the valve, make sure you plug them back in correctly. 3. Do not pull or push the tubes hard. Use... Read more
Fix a light that won't turn on or flickers in your refrigerator. This E12 socket replacement is straightforward with our step-by-step video guide.
When diagnosing the problem, I discovered that the ice door was not properly sealing and that the solenoid had appeared to rust/corrode forcing the door open. I replaced most of the ice dispenser internals (solenoid, crank, door, and spring) following the video. The door will now open when dispensing ice (which it does!), and will oddly stay open for a few seconds once I am finished, but does seal properly and the chute/container no longer frosts over. Read more
Fix a frozen evaporator coil with this defrost heater assembly. Restores proper cooling when frost buildup blocks airflow. DIY repair in 2-3 hours.
After doing a lot of web searching about the problem. It all came down to AppliancePartsPros.com. Watching the repair videos and learning what to do made the job a breeze. The only difficult problem was to thaw out the ice build up on the coils, which took 2 hours. The rest was easy. now I have a freezer/ fridge that is working like new. The total cost of the parts was less then having a repairman come out to look at it. AppliancePartsPros saved me a lot of money. Thanks! Read more
Refrigerator not cooling or compressor clicking on and off? This compressor kit restores cooling. Requires certified technician with specialty tools.
Protects the freezer light bulb from damage while maintaining visibility. Replace if cracked, yellowed, or broken. Confirm fit with your model number.
Replace solenoid, flapper door and recess spring. Really only needed solenoid, but other parts were so inexpensive and I knew I would already be in there. Read more
Ice won't dispense or drive spins freely? This auger drive coupler connects the motor to the ice bucket. Moderately difficult repair with basic tools.
The auger in ice bucket was frozen and locked in place (some how liquid water must have spilled inside and froze the shaft and bushing). When the motor was activated to deliver ice, the jam caused the motor shaft to strip the threads. With the threads stripped, there is no way (that I could find) to get the drive auger off of the shaft (btw, it is left-hand threaded). Apparently the Drive Auger is made of stainless steel - a harder metal then the motor shaft. To repair it, I removed the... Read more
Fixed-position freezer shelf for side-by-side refrigerators. Replace cracked, broken, or missing shelves to restore storage capacity and organization.
Refrigerator door dairy compartment for storing butter and small items. Replace this bin if cracked, broken, or missing to restore organized door storage.
The old Ice stripper had broken fingers. I realized that even with the new one I had to shave some of the plastic to allow the rotating arms to clear as they push out the ice. I did this very easily with a box cutter razor blade. the Compartment tray was merely a remove and snap into place. Read more