Psf26ngwc Parts

This ice dispenser deflector mounts in the freezer door chute to guide cubes or crushed ice into your glass. Replace a cracked or missing deflector to reduce scatter and keep ice flowing where you want it.

• Directs ice down the dispenser chute toward the glass
• Helps contain spray and bounce-back of cubes
• Restores proper flow when the original deflector is cracked, warped, or missing
• Common symptoms: ice misses the glass, ice scatters on the floor, visible damage to the deflector

• Disconnect power to the refrigerator before servicing; wear cut-resistant gloves
• Access the dispenser area per your model's instructions and note the deflector's orientation
• Transfer any screws or clips from the old part; avoid forcing plastic tabs
• Restore power and test ice dispense to confirm proper direction and clearance

This door lower hinge bushing installs in the bottom of the refrigerator door and rides on the hinge pin to create a smooth pivot point. Replacing a worn bushing restores proper door alignment, quieter movement, and reliable sealing.

• Provides a bearing surface between the lower hinge pin and the door
• Helps maintain door height and alignment for consistent gasket contact
• Common symptoms: door sagging or rubbing, squeaks, hard opening/closing, or door not closing flush
• Reduces hinge friction and wear at the bottom pivot

• Disconnect power; if applicable, turn off water to the door
• Remove door contents, support the door, and remove lower hinge hardware; lift door straight up
• Pull the old thimble from the door bottom and press the new bushing fully into place
• Reinstall the door, tighten hardware, and verify alignment and gasket seal

The Slide Out Shelf is an OEM part for GE refrigerators. It is designed to provide convenient and adjustable storage space within the refrigerator. This shelf allows for easy access to food items and can be slid out to reach items at the back more easily, enhancing the overall organization and usability of the refrigerator.

Over time, the slide out shelf can become damaged or worn out due to repeated use or heavy loads. This can result in difficulty sliding the shelf or instability when holding items.

Symptoms of a bad slide out shelf include:

• Difficulty sliding the shelf in and out
• The shelf not staying in place or wobbling
• Cracks or breaks in the shelf material

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This door thimble is the bushing that lines the upper hinge on your refrigerator door, supporting the hinge pin so the door swings smoothly, stays aligned, and helps reduce squeaks and wear.

• Provides a smooth bearing surface for the upper hinge pin
• Helps keep the door level and properly aligned with the cabinet
• Reduces friction and noise when opening and closing
• Replace if cracked, worn, or missing, which can cause door sagging, scraping, or poor closing

• Disconnect power and remove items from the door before servicing
• Support the door; remove the upper hinge cover and screws
• Lift the door off the hinge pin and remove the worn bushing from the hinge bracket
• Press the new thimble fully into place, reinstall the door, and verify proper alignment and seal

This Grille Recess is the dispenser drip tray that sits in the refrigerator's dispenser recess. It catches stray water and ice and provides a stable resting surface for your cup, helping keep the area clean and tidy.

• Collects drips and splashes from water/ice dispensing to help protect door surfaces
• Provides a stable platform for cups while filling
• Replace if cracked, warped, stained, or missing
• Can help reduce puddling around the dispenser area

• Disconnect power before servicing
• Lift out the old grille from the dispenser recess; clean any buildup
• Align and press the new grille into place until fully seated; do not force

This armature kit is the moving plunger and linkage operated by the dispenser solenoid. It opens and closes the ice chute door during dispensing and helps it seal when idle to reduce frost and warm-air leaks.

• Converts the solenoid's electrical action into mechanical movement for the dispenser ice chute door
• Helps maintain a proper seal to limit frost and moisture around the dispenser
• Typical symptoms: ice won't dispense; chute door won't open/close; frost/ice buildup at the chute; loud buzzing or clicking from the dispenser area
• Wear or sticking of the armature/spring can hinder movement and affect dispenser operation

• Unplug the refrigerator and shut off water to the dispenser before servicing
• Access the dispenser mechanism in the door; remove trim/control panel per your model's service information
• Note the orientation of the armature, spring, and linkage; transfer components one-for-one to the new kit and secure hardware
• Verify the solenoid plunger moves freely, reassemble, restore power, and test dispenser operation

This freezer shelf trim replaces a damaged or missing edge piece on the freezer shelf. It attaches to the shelf/frame to provide a finished lip that helps contain items and restores the shelf's original fit and appearance.

• Provides the finished edge on a freezer shelf to help keep items from sliding off
• Attaches to the shelf/frame for a secure, correct fit
• Replace when cracked, warped, loose, or missing
• Common symptoms include a broken or jagged shelf edge, trim that won't stay attached, or items slipping off the shelf

• Unplug the refrigerator and remove items from the affected shelf
• Remove the shelf if needed; release and remove the old trim
• Align the new trim with the shelf/frame and press until fully seated and secure
• Do not force parts together; inspect the shelf/frame for damage before reassembly

This door stop mounts on the refrigerator hinge to limit the door's swing and prevent overextension that can damage cabinets, hinges, or wiring. Replacing a worn stop restores smooth, controlled door opening and proper clearance.

• Controls the door's opening range by acting as a hinge stop
• Helps prevent the door from striking walls or adjacent cabinets
• Replaces cracked, missing, or deformed stops that allow overextension
• Common symptoms: door swings too wide, scraping/clicking at the hinge, or a visibly broken stop

• Unplug the refrigerator and, if applicable, shut off the water supply
• Remove the hinge cover; support the door to relieve weight on the hinge
• Lift the door off the hinge or remove the hinge pin as required; note the stop's orientation
• Install the new stop, reassemble, and verify door alignment and gasket seal

This ice dispenser auger drive mounts on the dispenser motor shaft and engages the ice bucket auger. Replacing a worn or stripped drive restores the connection so your refrigerator can move ice smoothly to the chute.

• Couples the dispenser motor to the ice-bin auger to rotate and move ice toward the chute
• On models with crushers, also drives the crushing mechanism
• Worn or rounded splines can cause little or no ice dispensing even though the motor runs
• May produce clicking/grinding noises from the door during dispense
• Visible cracking or play at the coupling indicates replacement is needed

• Unplug the refrigerator and shut off water before servicing
• Remove the ice bin to access the dispenser motor shaft in the freezer door
• Note the orientation; remove the old drive and seat the new drive fully on the shaft, transferring any original hardware if present
• Reinstall the ice bin, restore power, and test ice dispense

The Freezer Light Cover is an OEM replacement part for GE refrigerators designed to protect the light bulb in the freezer compartment from any potential damage or breaks. It helps maintain a safe and well-lit freezer environment, making it easier to locate and retrieve items.

A bad freezer light shield cover can occur due to regular wear and tear or accidental damage. If you notice symptoms such as a flickering or dim freezer light, or if the light bulb is exposed and vulnerable, it may indicate a need to replace this part.

Symptoms of a bad freezer light cover include:

• Flickering or dim freezer light
• Exposed or broken light bulb
• Insufficient lighting 

Restore lighting in your freezer by replacing the faulty freezer light cover with this genuine OEM part.

This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 
 

Water line from water valve up to icemaker fill tube.

The recess door retainer secures the dispenser's ice chute flapper in the refrigerator door. Replacing a cracked or missing retainer restores proper flapper pivot and sealing to help reduce frost buildup and air leaks around the dispenser.

• Holds the recess/ice door on its pivot within the dispenser assembly
• Helps the flapper close fully to seal the ice chute
• Restores smooth open/close action of the dispenser door
• Common symptoms: loose or fallen flapper, poor chute seal, frost or condensation in the dispenser area, and ice clumping near the chute

• Unplug the refrigerator before servicing the dispenser
• Carefully remove the dispenser bezel/control panel to access the ice chute door assembly
• Note spring orientation and retainer position; transfer components to the new retainer
• Verify flapper movement and seal before reassembly and restoring power

This fixed-position freezer shelf restores sturdy, level storage space in your freezer compartment. Replace a cracked or missing shelf to regain capacity and keep items organized with proper spacing for airflow.

• Provides a stable platform for storing frozen foods
• Maintains designed spacing to support organization and airflow
• Direct replacement when the original shelf is broken, warped, or missing
• Common symptoms: cracked/broken shelf, sagging, items tipping, reduced usable space

• Unplug the appliance and clear the freezer area before replacing the shelf
• Align the shelf with the designated side rails/slots and insert level
• Ensure both sides are fully seated and secure before loading items
• Avoid overloading to prevent damage

GLIDE BUCKET RH

This is the rear motor cover used in select GE refrigerators. It shields the motor area at the back of the compartment, helping direct airflow and protect the fan/motor assembly for reliable cooling performance.

• Protects the motor/fan area from debris and damage
• Helps channel air correctly through the compartment
• Cracks, broken tabs, or missing cover can lead to noise, poor airflow, frost, or temperature swings
• Restores proper fit and finish inside the compartment

• Unplug the refrigerator before servicing
• Remove shelves/bins obstructing access; retain screws/clips
• Carefully release locking tabs and transfer any reusable hardware
• Ensure the cover seats fully and resecure all fasteners before powering on