Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Directs defrost water from the evaporator to the drain pan below your refrigerator. Replace if cracked, damaged, or clogged to prevent water pooling.
Pulled down the existing drain tube and installed new one. Tight area so it requires two hands to push up and attach the new tube. The short rubber tubing attached to the new drain tube has to fit snug onto the plastic tube connection that hangs down. Replacing the water dispenser tray is simple and no explanation needed, Read more
Ice dispenser not working or just humming? The auger motor drives ice delivery. Easy DIY fix in under 15 minutes with our video guide. Restore ice flow.
Replaced auger motor Read more
The Screw is an OEM part for GE refrigerators. It serves a crucial function in securing and allowing smooth operation of the refrigerator's drawer rollers.
Causes of a bad or missing screw can include accidental loss during repair or maintenance, stripping of the screw threads due to overtightening, or general wear and tear over time.
Symptoms of a loose or screw include:
This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.
Used the schematic provided to select the parts needing replacement and placed the order. Parts arrived and swapping new for old was simple. For the most part it was a matter of taking out the old and putting in the new. There were a few screws with wheels to replace but that was easy as well. Before purchase I searched several different sites and found all the parts needed. I compared prices of each item as well as shipping cost. Prices for each item were nearly identical between sites... Read more
Seals your refrigerator's fresh food door to prevent air leaks and maintain proper temperature. Replace if torn, cracked, or door won't stay closed. Verify fit.
Ordered replacement seals for both freezer and refrigerator sides. Followed directions that I had found on YouTube. The installation in a nut shell is warm the seals in a bathtub with very hot water for at least 2-3hrs then place the seals. Then warm the seals with a hair dryer as needed. After getting the seals out of the hot bath the installation took all of 20-25 minutes for both seals. Read more
Replaces a cracked, broken, or worn ice chute funnel in your refrigerator door dispenser. Directs ice from the auger to your glass or container.
Replaced parts. I viewed YouTube video prior. Easy installation. Read more
Rubber grommet seals the ice maker fill tube where it enters the refrigerator cabinet. Replace if cracked, brittle, leaking, or missing to restore seal.
Replaced original (18 yrs.) 1/4" plastic tubing, clamp and grommet (AppliancePartsPros/GE parts) from outlet of ice maker water control valve to ice maker inlet. Also replaced water supply line to inlet of water control valve with new, GE braided, PEX 1/4" supply line with pre-attached female compression fittings on both ends. Repair job with AppliancePartsPros parts from outlet of water control valve went perfectly well, was simple, and had no leaks when tested. Parts were easy to install,... Read more
This black lever assembly operates the freezer door handle mechanism, allowing smooth opening and secure closing of the freezer compartment. It connects the external handle to the internal door latch system. Replace this part if your freezer door handle is loose, won't open the door, or if the handle feels disconnected when pulled.
I replaced the lever asm. and spring Read more
This is a grommet and gasket assembly that seals the ice maker water fill tube where it passes through the freezer wall. It prevents warm air from entering the freezer compartment and stops moisture from building up around the fill tube opening. Replace this assembly if you notice frost or ice buildup around the fill tube entry point, water leaking near the ice maker, or if the existing grommet is cracked or deteriorated.
Replaced water line from valve to ice maker Read more
Snaps onto freezer shelf edge to secure glass liner and provide finished front lip. Replace cracked, broken, or missing trim to restore clean appearance.
Purchased shelf. Read more
Seals the back edge of your refrigerator's crisper cover to maintain proper humidity and airflow. Replace if worn, cracked, or causing gaps. Confirm fit by model.
I thought I would have to buy a whole new refrigerator, but I looked online at AppliancePartsPros.com. I put in my model number of the refrigerator and the whole diagram came up. This made it so much easier to choose the parts I need to replace. I received the order in a few days so I was able to fix the problem quickly. The assembly was easy and the video helped also. Read more
Fix food freezing or warm spots in your fridge with a new air damper assembly. Controls airflow between compartments. Moderate DIY repair, 1-2 hours.
It started with clicking sounds for about 10 seconds at random times throughout the day. eventually the clicking sounds were gone and the temperature in the fresh food section was dropping below freezing. Turns out that one of the 3 damper doors was stuck open. My fridge has a damper door in the top left and 2 doors in the bottom left. One of the bottom doors was dedicated to the quick chill drawer which hadn't worked in some time. but since the quick chill door was stuck closed it did not... Read more
Plastic shelf stop locks refrigerator shelves into liner slots. Replace if cracked, broken, missing, or lost during cleaning to secure shelves properly.
Watched short You Tube repair video. I saved at least on a $100 GE service call. The electronic ID assembly was priced much less than quote on GE.com! Read more
Fix no water dispensing or leaking behind your refrigerator. This water inlet valve controls flow to the ice maker and dispenser. DIY repair in under an hour.
Fridge is 14 years old, ordered the water valve assembly and hose. Removed and replaced both Read more
This helix is the plastic spiral inside the refrigerator's ice bucket that works with the auger to move ice toward the crusher and dispenser. Replacing a worn or broken helix restores smooth ice dispensing and reduces jams.
Ice was not being dispensed when lever was pushed in either crushed or cubed mode I removed the ice bin. After searching the web for reasons for this I pulled the bin out and started looking at auger assembly. I noticed that the sections of the Helix blades were missing. Ordered the Helix here at AAP and received the part the next day. The whole process took about an hour and as others have noted, you have to disassemble the bin assembly to get the auger assembly out. I watched the video... Read more
The Glide Bracket is an OEM part for GE refrigerators. This left bracket supports the refrigerator drawer, allowing it to slide in and out smoothly for easy access to stored items.
Causes of a bad glide bracket can include regular wear and tear, damage from overloading the drawer, or accidental impact that causes the bracket to crack or break.
Symptoms of a bad glide bracket include:
This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
The hinge broke on the ice dispenser funnel and housing. I took them off and replace them, putting the old switches and bulb in the new housing. It took some time to put the return spring back because it does not appear in the assembly diagram. Once working, it secures to the door with 4 screws, and worked as it should. The support slide inside the freezer is held with two 1/4 in screws that were taken off with a nut driver. the rear screw is hard to get at. The new bracket just screws on, and... Read more
The Ice Deflector Spring is an OEM replacement part for GE refrigerators. This spring is a crucial component of the ice dispensing system, specifically in selecting between crushed and whole ice cubes. It is designed to always force the diverter back in a way that the cubes get crushed. When whole cubes are selected, the solenoid pulls the lever against the spring’s tension to shift the configuration, allowing cubes to bypass the crusher blades.
Causes for a malfunctioning Ice Deflector Spring can include wear and tear from regular use, corrosion due to constant exposure to moisture, or mechanical failure that prevents it from effectively reverting the diverter to the crushed ice configuration.
Symptoms of a bad Ice Deflector Spring include:
When I took it apart I found that the drive cup was cracked, the helix lock plate hole was reamed out and the ice deflector spring was broken. The biggest problem was the helix had slipped down the shaft and allowed the end of the shaft to bore a hole in the housing which made it a bear to get out. Others have had the same problem. Once I got past that obstacle, it was simple to replace all the parts and it's working like normal again. Very helpful video explaining the repair. Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.