Pss25ngna Parts

The Drain Tube is an OEM part for GE refrigerators. It is responsible for directing defrost water to the drain pan located beneath the appliance, where it can evaporate safely. 

Causes of a bad drain tube can include blockages from debris or ice, physical damage such as cracks or splits that allow water leakage, or a disconnection from its fitting points due to improper installation or material fatigue.

Symptoms of a bad Drain Tube include:

• Water pooling at the bottom of the refrigerator compartment
• Ice accumulation in or around the freezer area
• Leakage of water onto the kitchen floor beneath the refrigerator

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Fresh Food Door Gasket is an OEM replacement part for GE refrigerators. It forms an air-tight seal around the fresh food door preventing air and moisture exchange between the refrigerator interior and exterior. The gasket helps to maintain the ideal temperature and humidity levels inside for optimal food storage.

Causes of a bad gasket can include cracks, tears, or worn-away sections compromising the air-tight seal over time. Exposure to heat, moisture, or chemicals during cleaning may also degrade sealing qualities.

Symptoms of a bad gasket include:

• Cool air leaking from around the door
• Interior surfaces becoming wet or frosty
• Difficulty maintaining proper interior temperature settings

This GE OEM replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This air damper assembly regulates the flow of cold air from the freezer into the refrigerator compartment to keep temperatures even. Replace a stuck or broken damper to restore proper cooling and prevent warm spots or food freezing.

• Controls and meters airflow from the freezer to the fresh food section
• Opens and closes in response to temperature control signals to maintain set temperatures
• Helps balance cooling across shelves and drawers for consistent performance
• Failure symptoms include: refrigerator too warm, items freezing in the fresh food section, temperature swings, or clicking/buzzing from the damper area

• Disconnect power before servicing; remove food and shelves to access the damper area
• Remove the damper cover/grille; take out mounting screws or clips and withdraw the assembly
• Position the new assembly squarely in the air channel; reconnect any harness and reinstall covers
• Restore power and allow the refrigerator to stabilize before final temperature checks

The Ice Deflector Spring is an OEM replacement part for GE refrigerators. This spring is a crucial component of the ice dispensing system, specifically in selecting between crushed and whole ice cubes. It is designed to always force the diverter back in a way that the cubes get crushed. When whole cubes are selected, the solenoid pulls the lever against the spring’s tension to shift the configuration, allowing cubes to bypass the crusher blades.

Causes for a malfunctioning Ice Deflector Spring can include wear and tear from regular use, corrosion due to constant exposure to moisture, or mechanical failure that prevents it from effectively reverting the diverter to the crushed ice configuration.

Symptoms of a bad Ice Deflector Spring include:

• The ice dispenser only dispensing whole cubes, even when crushed ice is selected
• The diverter not returning to the crushed ice configuration
• Unusual sounds during the ice dispensing process
• The need for manual intervention to get crushed ice

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Glide Bracket is an OEM part for GE refrigerators. This left bracket supports the refrigerator drawer, allowing it to slide in and out smoothly for easy access to stored items.

Causes of a bad glide bracket can include regular wear and tear, damage from overloading the drawer, or accidental impact that causes the bracket to crack or break.

Symptoms of a bad glide bracket include:

• Difficulty sliding the drawer in and out
• The drawer not aligning properly or coming off its tracks
• Unusual noises when opening or closing the drawer
• Visible cracks or breaks in the bracket

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Shelf Stop is an OEM replacement part for GE refrigerators. The shelf stop in your refrigerator is what locks the shelf into the refrigerator liner.The shelf stop features a small protruding nub that fits into pre-cut slots in shelf supports, preventing shelves from being inserted too far. 

Causes of a bad shelf stop can include wear over many years of shelf adjustment, or damage from impact with shelves.

Symptoms of a bad shelf stop include:

• Shelves no longer fitting tightly or sitting flush in walls
• Ability to insert shelves further than intended design position
• Shelves shifting positions or becoming loose during use

This is a genuine OEM part that works for some models of GE, and Hotpoint models.

Color: Black

The Screw is an OEM part for GE refrigerators. It serves a crucial function in securing and allowing smooth operation of the refrigerator's drawer rollers.

Causes of a bad or missing screw can include accidental loss during repair or maintenance, stripping of the screw threads due to overtightening, or general wear and tear over time.

Symptoms of a loose or screw include:

• Loose or wobbly refrigerator drawer
• Difficulty opening or closing the drawer smoothly
• Scraping or grinding noises when operating the drawer
• Drawer coming off the track or rollers entirely

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Freezer Door Lower Hinge Bushing is an OEM replacement part for GE refrigerators. It is a component located within the freezer door hinge.

Causes of failure typically involve normal wear over extended use. Refrigerator doors experience frequent adjustment which can deteriorate hinge bushings.

Symptoms of a bad lower hinge bushing include:

• The freezer door being loose or wobbly in its closed position
• Excessive noise, grinding, or vibration coming from the door hinge area
• Difficulty smoothly opening or closing the door

This is a genuine OEM part that works for some models of GE, and Hotpoint models.

This rear gasket fits the refrigerator's crisper cover, sealing the back edge of the glass/frame. It helps maintain proper airflow and humidity in the crisper area while cushioning the glass and reducing rattles and gaps.

• Creates a seal along the rear edge of the crisper cover to limit air leaks
• Helps maintain consistent humidity and airflow in the crisper compartment
• Cushions and supports the glass to minimize vibration and noise
• Replace if torn, flattened, missing, or if you see gaps or glass rattle

• Unplug the refrigerator before servicing
• Remove crisper drawers and carefully lift off the glass cover/frame
• Pull the old gasket from the rear channel and clean the mating surfaces
• Press the new gasket fully into the rear channel; reinstall cover and drawers, checking for an even seal

The Gasket Evaporator Cover is an OEM part for GE refrigerators. This part seals the evaporator cover, ensuring that cold air does not escape and that the refrigerator operates efficiently. 

Causes of a bad Gasket Evaporator Cover can include wear and tear over time, exposure to extreme temperatures that degrade the material, or physical damage that breaks the seal.  

Symptoms of a bad Gasket Evaporator Cover include:

• Noticeable frost buildup in the freezer compartment
• The refrigerator runs more frequently or for longer periods
• An increase in energy consumption
• Difficulty maintaining consistent temperatures within the refrigerator

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Ice Crusher Housing is an OEM part for GE refrigerators. This part provies a protective enclosure that ensures the ice is crushed efficiently and safely before being dispensed.

Causes of a bad ice crusher housing can include wear and tear from regular use, damage from ice jams or foreign objects, and exposure to temperature fluctuations.  

Symptoms of a bad ice crusher housing include:

• Ice not being crushed properly
• Ice jams or blockages in the dispenser
• Leaks or cracks in the housing
• Unusual noises during the ice crushing process

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Temperature Sensor Grille is an OEM part for GE refrigerators. This grille covers and protects the temperature sensor, ensuring it accurately measures the internal temperature of the refrigerator.  

Causes of a bad grille can include physical damage from impacts, regular wear and tear, or the buildup of dust and debris that can obstruct airflow.  

Symptoms of a bad temperature sensor grille include:

• Inaccurate temperature readings
• The refrigerator running continuously or not cooling properly
• Visible damage or obstruction on the grille
• The sensor becoming loose or dislodged

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

The Crisper Pan is an OEM part for GE refrigerators. This pan is designed to store fruits and vegetables at an optimal humidity level, helping to keep them fresh for longer periods. It slides into the lower section of the refrigerator and provides a clear view of its contents, making it easy to organize and access your produce.

Over time, the crisper pan can become damaged or cracked due to regular use, accidental impacts, or overloading. A damaged crisper pan can lead to inefficient storage and potential spoilage of fruits and vegetables.

Symptoms of a bad crisper pan include:

• Cracks or splits in the plastic
• Difficulty sliding the pan in and out
• Excess moisture accumulation in the crisper
• Decreased ability to keep produce fresh

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This ice dispenser deflector mounts in the freezer door chute to guide cubes or crushed ice into your glass. Replace a cracked or missing deflector to reduce scatter and keep ice flowing where you want it.

• Directs ice down the dispenser chute toward the glass
• Helps contain spray and bounce-back of cubes
• Restores proper flow when the original deflector is cracked, warped, or missing
• Common symptoms: ice misses the glass, ice scatters on the floor, visible damage to the deflector

• Disconnect power to the refrigerator before servicing; wear cut-resistant gloves
• Access the dispenser area per your model's instructions and note the deflector's orientation
• Transfer any screws or clips from the old part; avoid forcing plastic tabs
• Restore power and test ice dispense to confirm proper direction and clearance

This door lower hinge bushing installs in the bottom of the refrigerator door and rides on the hinge pin to create a smooth pivot point. Replacing a worn bushing restores proper door alignment, quieter movement, and reliable sealing.

• Provides a bearing surface between the lower hinge pin and the door
• Helps maintain door height and alignment for consistent gasket contact
• Common symptoms: door sagging or rubbing, squeaks, hard opening/closing, or door not closing flush
• Reduces hinge friction and wear at the bottom pivot

• Disconnect power; if applicable, turn off water to the door
• Remove door contents, support the door, and remove lower hinge hardware; lift door straight up
• Pull the old thimble from the door bottom and press the new bushing fully into place
• Reinstall the door, tighten hardware, and verify alignment and gasket seal