Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Replacement door closure spring for refrigerator hinges. Installs on door hinge assembly to provide tension for proper closing. Needed when broken or worn.
I replaced the lever asm. and spring Read more
This is a grommet and gasket assembly that seals the ice maker water fill tube where it passes through the freezer wall. It prevents warm air from entering the freezer compartment and stops moisture from building up around the fill tube opening. Replace this assembly if you notice frost or ice buildup around the fill tube entry point, water leaking near the ice maker, or if the existing grommet is cracked or deteriorated.
With new hose Read more
Seals your refrigerator's fresh food door to prevent air leaks and maintain proper temperature. Replace if torn, cracked, or door won't stay closed. Verify fit.
Ordered replacement seals for both freezer and refrigerator sides. Followed directions that I had found on YouTube. The installation in a nut shell is warm the seals in a bathtub with very hot water for at least 2-3hrs then place the seals. Then warm the seals with a hair dryer as needed. After getting the seals out of the hot bath the installation took all of 20-25 minutes for both seals. Read more
Snaps onto freezer shelf edge to secure glass liner and provide finished front lip. Replace cracked, broken, or missing trim to restore clean appearance.
Bought shelf. Transaction smooth. Read more
Fix food freezing or warm spots in your fridge with a new air damper assembly. Controls airflow between compartments. Moderate DIY repair, 1-2 hours.
It started with clicking sounds for about 10 seconds at random times throughout the day. eventually the clicking sounds were gone and the temperature in the fresh food section was dropping below freezing. Turns out that one of the 3 damper doors was stuck open. My fridge has a damper door in the top left and 2 doors in the bottom left. One of the bottom doors was dedicated to the quick chill drawer which hadn't worked in some time. but since the quick chill door was stuck closed it did not... Read more
This black lever assembly operates the freezer door handle mechanism, allowing smooth opening and secure closing of the freezer compartment. It connects the external handle to the internal door latch system. Replace this part if your freezer door handle is loose, won't open the door, or if the handle feels disconnected when pulled.
Seals the back edge of your refrigerator's crisper cover to maintain proper humidity and airflow. Replace if worn, cracked, or causing gaps. Confirm fit by model.
I thought I would have to buy a whole new refrigerator, but I looked online at AppliancePartsPros.com. I put in my model number of the refrigerator and the whole diagram came up. This made it so much easier to choose the parts I need to replace. I received the order in a few days so I was able to fix the problem quickly. The assembly was easy and the video helped also. Read more
Plastic shelf stop locks refrigerator shelves into liner slots. Replace if cracked, broken, missing, or lost during cleaning to secure shelves properly.
Watched short You Tube repair video. I saved at least on a $100 GE service call. The electronic ID assembly was priced much less than quote on GE.com! Read more
The Glide Bracket is an OEM part for GE refrigerators. This left bracket supports the refrigerator drawer, allowing it to slide in and out smoothly for easy access to stored items.
Causes of a bad glide bracket can include regular wear and tear, damage from overloading the drawer, or accidental impact that causes the bracket to crack or break.
Symptoms of a bad glide bracket include:
This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
The hinge broke on the ice dispenser funnel and housing. I took them off and replace them, putting the old switches and bulb in the new housing. It took some time to put the return spring back because it does not appear in the assembly diagram. Once working, it secures to the door with 4 screws, and worked as it should. The support slide inside the freezer is held with two 1/4 in screws that were taken off with a nut driver. the rear screw is hard to get at. The new bracket just screws on, and... Read more
This evaporator fan motor dust cap is an authentic OEM replacement part found on refrigerator and freezer fan motors. This dust cap prevents the fan motor bearing and housing from being damaged by dirt and debris. If the dust cap is cracked or broken, the fan may make loud squealing noises. If the dust cap is not removed and replaced, the fan could stop working and ultimately cause the refrigerator's temperature to be affected. To start, disconnect the power and water to the refrigerator. Remove food from the freezer so that the back panel of the freezer can be accessed to reach the fan. Remove the ice maker and set it outside the freezer. Disconnect the fan and take it out of the freezer to expose the fan's shaft and the dust cover. Pry the dust cover off and install the new one. Replace the fan and cover. Reconnect the wires and reinstall the icemaker. Put the food back in the freezer. Reconnect the power and water.The evaporator fan motor dust cap is a white plastic part that is sold individually. This dust cover is made for use in refrigerators manufactured by General Electric, Hotpoint, and Kenmore.
Replacement of the evaporator fan motor, fan blade, and grommets. The amount of disassembly to reach the part took most of the effort Read more
The Ice Deflector Spring is an OEM replacement part for GE refrigerators. This spring is a crucial component of the ice dispensing system, specifically in selecting between crushed and whole ice cubes. It is designed to always force the diverter back in a way that the cubes get crushed. When whole cubes are selected, the solenoid pulls the lever against the spring’s tension to shift the configuration, allowing cubes to bypass the crusher blades.
Causes for a malfunctioning Ice Deflector Spring can include wear and tear from regular use, corrosion due to constant exposure to moisture, or mechanical failure that prevents it from effectively reverting the diverter to the crushed ice configuration.
Symptoms of a bad Ice Deflector Spring include:
When I took it apart I found that the drive cup was cracked, the helix lock plate hole was reamed out and the ice deflector spring was broken. The biggest problem was the helix had slipped down the shaft and allowed the end of the shaft to bore a hole in the housing which made it a bear to get out. Others have had the same problem. Once I got past that obstacle, it was simple to replace all the parts and it's working like normal again. Very helpful video explaining the repair. Read more
Protective grille cover that mounts over the temperature sensor in your refrigerator. Replace if cracked, broken, or missing to properly shield the sensor.
Common theme on the blogs was thermistors and or defrost heater/thermostat. Ran self-diagnostics which turned on defrost heater which was fine. All five thermistors indicated ok on diagnostic also, but I read more than one time "replace the thermistors no matter what if your FF section isn't cooling". So I ordered all five thermistors and defrost limiter thermostat. Received all in 48 hours (great shipping service), took me about three hours to replace all thermistors and thermostat just as... Read more
Fix no water dispensing or leaking behind your refrigerator. This water inlet valve controls flow to the ice maker and dispenser. DIY repair in under an hour.
Fridge is 14 years old, ordered the water valve assembly and hose. Removed and replaced both Read more
Ice cubes stuck together or ice maker not ejecting? The ice stripper removes ice from the mold during ejection. Easy snap-in repair with video guide.
Replaced the parts. Initially, in order to ensure the ice maker itself was still working, I did some repairs to test it. I repaired the cracked crusher cover with a plastic welder, I also repaired the glide bucket Lh with the plastic welder & some epoxy. I attached the broken ice stripper pieces with the plastic welder. If the ice maker made ice I knew it was safe to buy new parts. It made ice for two days only but after it dropped ice the first time I ordered the parts. Parts did not... Read more
Plastic bushing that fits inside the lower freezer door hinge assembly. Replace when cracked, worn, or broken to restore smooth door operation.
Seals the evaporator cover to prevent cold air leaks and maintain cooling efficiency. Replace if worn, cracked, or loose. Verify fit with your model number.
I watched the videos and ordered the parts to fix the problem. Then I installed them and so far everything seems to work ok. It's only been a few days so we'll see if I got it right. Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.