Need Help?
Call or text
Washer won't spin or agitate? A faulty lid switch magnet may be the cause. This part signals the switch that the lid is closed. Easy 20-minute DIY fix.
Replaced lid switch and lid magnet. Took just a little longer then 20 minutes as I had to splice in the new lid switch as it wasn't one that was a clip in, it was hard wired in. Read more
Suspension rod and spring assembly for washer drum stability. Replaces worn, broken, or weakened suspension components causing drum movement or sagging.
I have a 14 year old GE washing machine that had been making a lot of noise while running but had eventually just stopped flat. The agitator and spin cycle would not run. I found this site and made excellent use of all the repair videos to study about my issue. I put in my machine model number and I Immediately was able to start honing in on what my problem could be from website advice about popular repair parts, stories others had shared about their similar machine issues and watching videos,... Read more
Installation tool designed for installing washer drive belts. Provides proper leverage and positioning to seat belts correctly on pulleys and motor shafts.
Fix a washer that won't spin or agitates but doesn't spin properly. This mode shifter assembly switches between agitate and spin cycles. Advanced repair.
Motor control board was flashing 4 times, indicating that the mode shifter had an error. I disconnected the mode shifter's wire from the controller and measured the resistance between the 2 leads with an ohmmeter. Since the reading was infinite, that meant that the mode shifter coil or in-line thermal sensor was electrically open, i.e. bad. As this fix is near a complete tear-down of the washing machine, here are a few tips I discovered. 1) the hub nut is difficult to remove and you need a... Read more
Plastic support bracket that secures suspension rods to the washer cabinet. Replace when cracked, broken, or worn to restore proper drum suspension.
Mounting screw for washer components. Secures drain hose clamps, panels, and internal parts. Replace if missing, stripped, or lost during repair.
Put new hose on. It was the kind that pushed in and had a flange on it with two screws. Read more
Suspension rod and spring assembly for washing machines. Installs between the tub and cabinet frame. Replace when cracked, broken, or worn to restore stability.
I shopped around a bit - found one retailer that only had 1 shock in stock, another that only stocked the front shocks, etc. There is definitely a difference in the springs between the green colored and white colored shocks! I've torn this washer down before, so I'm fairly familiar with how it's put together. I've seen some of the You-tube videos on replacing this item, and some of the videos show far more disassembly than is required. I only removed the front, top, and controls, and... Read more
Replacement water fill hoses for washing machines. Connect home water supply to washer. Replace when cracked, leaking, or showing rubber wear or corrosion.
Fix grinding or scraping noise during agitation with this washer pulsator coupling. Located under the agitator, connects to drive shaft. DIY repair in 10 minutes.
I looked up a YouTube video first to know how to take my washing machine apart. It was an Appliance Parts Pros Video. Very helpful! I replaced the mode shifter, water pump, washers, agitator spline, hub nut, tub bearing, tub seal and drive belt. The hub nut DID NOT want to come off. I cut it off with my Dremel and chipped out the beveled segment with a heavy duty screw driver and 3# hammer. Had to be very careful to not damage the hub assembly. I removed the Torx screws and removed the... Read more
Replace your washer's damaged, rusted, or cracked lid assembly. Covers the drum to prevent splashing and ensure safe operation. Includes hinges.
Removing and Replacing (R&R) the parts took about 15 minutes. Getting the correct parts took several weeks. It was a severe struggle. Many of you will experience problems trying to get the correct "Lid" for similar GE washing machine models. AppliancePartsPros.com was great: Right price, Arrived quickly in good condition. I got the wrong part. It was not the fault of AppliancePartsPros.com, though. To make a long story short, GE has disseminated incorrect data in parts lists and it... Read more
Secures your washer's drain hose to standpipe, maintaining proper air gap to prevent siphoning and backflow. Replace if clip is broken or missing.
My son fixed it Read more
Baffle screw with flat washer for washers. Secures baffle or trim pieces to the washer body. Replace if screw is stripped, washer is missing, or worn.
Myself and help from friends. Read more
Drive pulley mounts to the washer basket shaft and routes the belt from the motor. Replace if worn, cracked, loose, or showing play on the shaft.
Replaced the shaft & mode shifter assembly. Also replaced the pulley as it had taken some damage from the wobbling clutch dog. And replaced the tub seal since it's normally inaccessible with the shaft in place. This is an advanced repair that took a lot of time. Removing the tub nut took a 1 11/16" socket and a 700 ft-lb impact wrench and I had to hammer on the nut for several minutes to break it free of the tub. Disassembly of the washer is complete, and requires a lot of space for... Read more
Seals the flood/overflow hose connection to your washer tub. Replace if water seeps from the tub area or the gasket feels soft. Confirm fit by model.
Pulled front panel off. Unbolted and removed top cover. Removed tub trim cover. Removed and replaced gasket and dampers. Put it a back together took about 20 minutes Read more
1/4-20 x 5/8 hex washer-head machine screw secures brackets, panels, and internal components. Replace worn, stripped, or missing fasteners.
The screw that holds the agitator in place appeared to have worn and rusty threads. I tried to replace it with a standard hardware store 1/4-20 hex head screw but that wouldn't grip. I had thoughts of needing to tap the hole,but eventually bought the specified screw, which is a specialist. It has tapered threads, a shoulder, rubber bushings, an attached washer and a hex head. I spent a lot of time trying other things but when the real part arrived it only took a few minutes to set it in place. ... Read more
Secures washer hoses at pump, tub, and valve connections to prevent leaks and hose blow-offs. Replace worn or missing clamps for a tight seal. Confirm fit.
The video was very helpful. the hardest part is getting off old rusted parts. I had to use a hacksaw to remove one of the old clamps. I had to open the bottom of the washing machine to remove of the other clamp. Putting the new parts on was easy. Getting everything apart was a challenge. Putting the new parts on was an easy 5 minute job. Read more