Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
This is a rubber gasket seal that fits between the outer tub halves or around the tub ring of a washing machine, creating a watertight seal to prevent leaks during the wash and spin cycles. It compresses between the tub components when they are clamped together. Replace this seal if you notice water leaking from around the outer tub, pooling under the washer, or if the seal appears cracked, hardened, or deformed.
This was some repair! My SG1000 stackable is over 30 years old and was purchased second hand. I've replaced many parts in the dryer section, but besides a water inlet, this was my first repair to the washer. All of a sudden it started making a terrible noise and was not agitating the clothes. The spin cycle worked fine. I first replaced the two belts on the bottom, but when I removed the old ones I realized they did not look terribly worn and weren't the cause. Many stories on here indicated... Read more
Seals the agitator shaft opening to prevent leaks and protect internal components. Replace if you see water leaking from the center post during wash cycles.
Found the wonderful parts diagrams you most generously share online and a couple of YouTube videos . I determined it should be repairable. In my cast the agitator shaft was frozen (rusted) in place. I was very fortunate to have been able to eventually remove it with the use of a lot of BP penetrating oil and heat. Long and short the replacement parts fit perfectly and the washer is running like new. Special thanks to the online support make my repair possible. Read more
Seals the water path at the injector assembly. Replace if you notice leaks during fill cycles or poor water flow. Confirm fit with your model number.
Replaced the Injector valve, nozzle and sleeve-in using new hose clamps Read more
Size: 90 inches long. To order hose extension use 12001585. To order siphon break use 76660.
Model# MAV7257AWW Maytag Atlantis Washing Machine. Repairs were fairly easy along with the videos appliancepartspros offers on their website. Parts also came with instructions on how to install. Other videos were available on You Tube. The only part difficult to install was Thrust bearing kit - make sure when installing to pull down on shaft so washer and e-clip will fit. Another note, you can get a pulley for your replacement motor pulley on eBay and Maytag.com. Just pay close attention to... Read more
This hose clamp secures a hose connection to prevent leaks and keep your appliance running smoothly. It provides a tight, reliable hold on the hose fitting so water or air stays contained during operation.
Took off cover, installed new parts. Read more
Connects water supply to the dispenser injector in your washer. Replace if cracked, nicked, or leaking. Installs at the top under the lid assembly.
First the parts showed up as promised in 2 days. Injector fill hose wasn't leaking but replaced to be on safe side. Everything went together just like OEM parts. Cost less then having my appliance guy just walk thru the door at $80.00 Read more
This replacement screw secures panels, brackets, and components inside appliances. Replacing a missing or stripped fastener restores a snug, rattle-free fit using the correct #8-18 thread and 5/8-inch length.
Replace Read more
This hose clamp secures a rubber or plastic hose to its fitting to maintain a tight, leak-resistant seal. Replace a worn or missing clamp to stop drips and keep appliance water connections secure.
I ordered the required parts from your website, the parts required were easily identified from the website tub blowup. The parts were delivered within 2 days and installed within 15 minutes Read more
Insulates and supports electrical connections through the dryer chassis. Replace if cracked, heat-damaged, or broken to prevent shorts and restore safety.
I ordered all the parts necessary to replace the heating element and thermostat on a Sunday night. Appliance Parts Pros shipped on Monday AM and I received them on Wednesday. It took me 45 minutes to disassemble the dryer, replace the parts and have the dryer working again. It should be good for another 35 years which should cover me for my needs. Thanks again to Appliance Parts Pros for having the best service and always the correct parts. I am a huge fan of your company as you never... Read more
Hose clamp for securing water supply and drain hoses on the washer. Provides leak-free seal at hose connection points.
Replace faucet adapter, replace fill and drain hose assembly. You must remove outer cabinet to be able to route new hoses and access hose connections under tub. Read more
This injector seal fits the refrigerator's water injector. It restores a tight, watertight/airtight connection where the injector passes through the liner or mates to the fill tube, helping prevent leaks and frost around the opening.
1. Sleeve for input, Injector valve, nozzle and seal for input fixed this problem. Probably the main part that was the trouble was a deformed Injector Valve which is a rubber tube with an internal retention groove at the wide part that grips the Nozzle. The Sleeve and the Nozzle are hard plastic parts that basically looked fine, but I replaced them anyway while I was in there. Additionally I replaced the rubber Seal for Input which seals the plastic input fitting to the tub just to make sure... Read more
This is a metal clip that secures the drive motor in place within the dryer cabinet. It clamps around the motor housing to prevent movement during operation. Replace this clip if it is broken, missing, or bent, which can cause the motor to shift and create excessive vibration, rattling noises, or belt misalignment.
We took the dryer out of the laundry room and took it apart, after reviewing numerous videos at Appliance Parts Pros for direction. Removed front panel, front bulkhead and drum. Then removed exhaust duct, blower assembly and finally motor. (Use large flat blade screw-driver to press very hard down and out on motor mount to remove). After reinstalling all components....motor, new exhaust duct work,front bearings in front bulkhead, and blower assembly, all went back together great. The most... Read more
Replacement mounting bolt for washer outer tub assembly. Secures tub components together with nut. Replace if rusted, stripped, loose, or missing.
We watched the video before we purchased the parts for this project. We wanted to make sure exactly what parts we would need. Thanks for having this information available. We purchased the mounting stem repair kit,,tub bearing kit, 3 new bolt/washers that hold the outer tub in place and the spanner wrench. Cleaned everything... NOTE :TAKE THE TIME TO CLEAN YOUR FILTERS ON THE BOTTOM. Thing went back together smoothly. We refereed back to the video when in doubt. Total repair $118.00... Read more
This clip and insulator assembly secures and electrically isolates a component inside a range or wall oven. It keeps the part firmly positioned while preventing shorts and heat damage, supporting accurate, safe appliance operation.
Fix a laundry center that won't spin, agitate, or hums without moving. This drive motor replacement requires moderate skill and 2-3 hours to install.
I've read several reports about how "easy and quick" it was to replace the motor. All I can say is, "nonsense". It wasn't as easy as others reported, but for someone with decent tool skills, it was a very doable home repair - just be prepared to spend some time on it. First, the motor needs to be accessed from the FRONT of the dryer. This means removing the two cover panels to access the interior. NOTE: take photos as you go of how all interior pieces for together to make reassembly easier -... Read more
Small drive gear inside the washer transmission gearcase that meshes with mating gears. Replace when worn, stripped, or damaged to restore power transfer.
American appliances are very easy to fix in comparison to imported ones. Just open the washer and take de transmission cover out change the pinion inside removing a simple retainer. In the agitator there is a screw that you loosen it take it out, then de tub and take the shaft out and put a new seal and a new c clamp and reinstall everything back. Top-loading washers are very easy to fix in comparison to front-loading washers that are very difficult to fix. Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.