Shx43c/46 Parts

The Hinge Lever (LH) is an OEM part for Bosch dishwashers. This left-hand lever is responsible for assisting in the opening and closing of the dishwasher door through a pivoting motion. The hinge lever works with other door components like springs and cables to provide smooth, balanced movement of the door. 

Symptoms of a bad Hinge Lever include: 

• Difficulty opening or closing the dishwasher door  
• The door not staying securely closed during the cycle
• Excessive noise or creaking coming from the door area
• Misalignment of the door 

Causes of a bad Hinge Lever can include normal wear and tear over time, damage from excessive force or weight on the door, or loose mounting hardware.

Note: Left hinge lever

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.
 

The Junction Box Cover is an OEM part for Bosch dishwashers. Located at the rear of the appliance, the junction box houses connections to the power supply and control board wiring. The junction box cover protects these internal electronic parts.

Symptoms of a bad junction box cover can include:

• Cracks, breaks or missing pieces of the plastic casing
• Exposed wires posing risk of electric shock
• Difficulties accessing internal components for service or repairs
• Potential water damage into electrical components

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

2 clamps included.

The Handle-Cap is an OEM part for Bosch dishwashers. It provides a contact point to open and access the dishwasher. As the cap wears through repeated use, it can impact usability.

Causes of a bad handle cap include typical wear over time. Harsh chemicals or impact can also damage this exterior part.

Symptoms of a bad handle cap are:

• Loose or improper fit that's uncomfortable
• Sharp edges or broken surfaces that could cut
• Discoloration or corrosion reducing aesthetic
• Difficulty opening the dishwasher door

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

The Drain Pump Cover is an OEM part for Bosch dishwashers. This cover protects the drain pump mechanism from debris while draining dirty water after each cycle.

Causes of a bad drain pump cover include cracks or breaks from heavy impacts over time.

Symptoms of an improperly functioning cover include:

• Leaks in the area around the drain pump
• Decreased drain and pump performance over time
• Potential clogs from broken pieces inside

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

The Upper Spray Arm Water Tube is an OEM part for Bosch dishwashers. It is a vital component of the washing mechanism responsible for spraying water across the upper rack. 

Over time, mineral deposits can clog the narrow openings of the water tube, reducing water pressure and spray effectiveness. Accidental bending or cracking of the flexible water tube could also cause spray issues.

Symptoms of a bad upper spray arm and water tube include: 

• Incomplete cleaning of dishes on the upper rack
• Dried food soils left behind after washing  
• Noticeably weaker water spray pressure from the arm
• Possible leaks or drips around the arm connection point

Replacing with this OEM Bosch part restores full spray coverage and optimized washing for all rack levels. It is also compatible with certain Miele, Asko, and Jenn-Air professional-grade dishwashers.
 

The Control Unit is an OEM component specifically designed for Bosch dishwashers. It houses all of the electronic components that operate and monitor dishwasher functions.  

The control unit works behind the scenes to coordinate different aspects of each cycle, from water inlet to drainage and motor functions. Integrated circuits and boards ensure precise wash times and temperatures.

Symptoms of a bad control unit include:

• Failure to start or run through cycles normally  
• Error codes or blinking lights that can’t be reset
• Unresponsive or inconsistent responses to control input
• Inability to heat water properly for sanitization  

Causes include moisture damage, power surges that can fry circuitry, or normal component degradation over thousands of hours of operation.  

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.
 

This metric M4 x 8 screw secures the toe-kick/lower access panel at the base of the appliance. Replace a missing or stripped fastener to keep the kickplate tight and aligned, helping prevent looseness and noise.

• Secures the toe-kick or lower access panel to the base/frame
• Restores proper fit when the original screw is lost or damaged
• Helps reduce panel rattles and vibration
• Maintains correct alignment and clearance at the bottom edge

• Disconnect power before servicing; also shut off the water supply
• Support the panel and align holes before threading the screw
• Start by hand to avoid cross-threading; tighten snugly—do not overtighten
• Verify size matches the original; replace matching hardware together if required by your model

This turbidity sensor detects how clear the dishwasher's wash water is so the control can adjust cycle time, rinses, and water changes. Replacing a faulty sensor helps restore proper cleaning performance and normal cycle lengths.

• Monitors soil level/clarity of the wash water
• Signals the control to extend or shorten wash and rinse phases as needed
• Helps optimize water use while maintaining cleaning results
• Failure symptoms can include unusually long or short cycles, poor cleaning, repeated draining/refilling, or cycles that won't advance

• Disconnect power and turn off the water supply before servicing
• Pull the dishwasher out as needed; access the sensor from the base area
• Place a towel to catch residual water; release the locking tab or twist-lock, unplug the connector, and install the new sensor fully seated and locked
• Restore power/water and run a test cycle; check for leaks

This O-ring is the sealing gasket between mating components, keeping fluid contained inside the system. Replacing a worn ring restores a tight, leak-free connection and helps prevent drips, moisture, and leak-related error indications.

• Creates a compressible seal between parts to prevent leaks at the joint
• Helps maintain proper system flow by stopping seepage or air ingress
• Direct replacement for rings that are flattened, cracked, brittle, swollen, or missing
• Common symptoms include dripping at the connection, moisture beneath the unit, or leak/float error alerts

• Disconnect power and shut off the water supply before servicing; wear appropriate PPE.
• Note the original ring's location; clean the groove and mating surfaces before installation.
• Apply a light coat of compatible silicone grease; avoid twisting or overstretching the ring.
• Seat evenly, reassemble, restore service, and check for leaks during a test cycle.

The Water Inlet System is an OEM component specifically designed for select Bosch dishwashers. Comprising inlet valve, screens, hoses, and connectors, it precisely meters fresh water. Reliable flow prevents mineral buildups from impairing performance.

Causes of a bad water inlet system commonly involve bursting hoses or stripped connectors. Prolonged pressure weakens seals requiring timely replacement.

Symptoms of a faulty water inlet system include: 

- Fluctuating or absent water flow to spray arms
- Leaks forming inside or near the installation site
- Errors relating to improper water temperature or amounts  

Causes of a bad water inlet system involve typical degradation such as:

• Limescale clogging narrow valve openings
• Plumbing joint corrosion compromising integrity
• Splitting plastic tubing unable to withstand cycles

This OEM Bosch part is also compatible with some Miele, Blomberg, and Thermador dishwashers. 
 

The Screw is an OEM replacement part for Bosch dishwashers. Hundreds of screws hold the appliance panels and internal mechanisms securely in place. Consistent, protective enclosures ensure long-lasting performance.

Causes of a bad screw can include stripped threads from repeated tightening/loosening during repairs. Corrosion posing integrity risks may develop if water penetrates screw heads over time. 

Symptoms of a bad screw include: 

• Panels or racks that rattle or come loose during operation
• Gaps appear that allow residual moisture to seep within
• Internal components shifting position from the original assembly
• Loose wiring susceptible to abrasion posing electrical hazards

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

This sump screw secures the dishwasher's sump or sump cover to the tub, keeping the assembly tight and leak-resistant. Replace a missing, stripped, or damaged screw to restore a proper seal and stable mounting.

• Fastens the sump or sump cover to the dishwasher tub
• Helps maintain a watertight seal to reduce leaks
• Keeps filter/sump components aligned and secure
• Replaces missing, stripped, or damaged hardware
• Helps address leaks or rattling around the sump area

• Disconnect power and turn off water supply before servicing
• Remove the lower rack and filters to access the sump area
• Ensure mating surfaces and seals are clean and properly seated
• Tighten snugly by hand; do not overtighten to avoid stripping

Includes door latch, strike plate and microswitch.

The Water Inlet Fill Hose is an OEM part for Bosch dishwashers. This part is responsible for safely and efficiently connecting the dishwasher to your home's water supply, ensuring that water flows into the dishwasher at the correct pressure and volume for optimal cleaning performance. 

Over time, the Water Inlet Fill Hose can become susceptible to wear and tear, leaks and blockages.

Symptoms indicating the need for a new Water Inlet Fill Hose include:

• Water pooling around the dishwasher base, pointing to a potential leak in the hose.
• The dishwasher not filling with water properly, or filling very slowly, suggesting a blockage or damage to the hose.
• A visible inspection reveals cracks, bulges, or signs of corrosion on the hose connectors.

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

Bosch dishwasher soap dispenser assembly, unvented, dark gray