T36bb820ss Parts

Removes impurities from your refrigerator's water and ice supply. Replace every 6 months for clean, fresh-tasting water. Verify fit by model number.

The Lock Clamp is an OEM replacement part for Bosch refrigerators. It is a fitting that secures the freezer drawer in its closed position. Made of durable metal and plastic, the lock-clamp features a latching mechanism to fasten the door shut with an audible click. 

Symptoms of a bad lock clamp include:

• The freezer door not closing or latching securely
• Warm air escaping from around the door seal  
• Noise from a loose or poor-fitting lock-clamp
• The door popping open unexpectedly

Causes of a bad lock clamp can include wear and tear of moving parts over time, broken clips or latches from repeated use.

This OEM Bosch replacement lock clamp is compatible also with Thermador and Gaggenau model refrigerators

Refrigerator door seal creates an airtight barrier to maintain internal temperature. Replace if cold air escapes or condensation forms. Confirm fit with model.

Retaining clip secures panels and components inside your refrigerator or freezer. Replace if cracked, broken, or missing to keep parts aligned.

The Bulb is an OEM part for Bosch ovens. This component provides illumination inside the oven, allowing you to easily monitor the cooking process without opening the door and losing heat.

Causes of a bad bulb can include filament burnout due to extended use, electrical issues that cause power surges, or physical damage from accidental impacts. 

Symptoms of a bad bulb include:

• The oven light not turning on
• Flickering light inside the oven
• Dim or uneven lighting
• The bulb appearing visibly damaged or burnt out

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

The Mullion Heater is an OEM part for Bosch refrigerators. It is designed to prevent condensation from forming on the refrigerator door mullion, the vertical divider between the doors. This heater ensures that the mullion stays warm enough to stop moisture from condensing and causing potential water damage or mold growth.

Causes of a bad mullion heater can include electrical failures, wear and tear from continuous use, or manufacturing defects.  

Symptoms of a bad mullion heater include:

• Visible condensation or frost on the door mullion
• Water pooling or dripping around the door area
• Increased humidity inside the refrigerator
• Mold or mildew developing near the door seal

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

This perimeter door seal fits into the dishwasher tub channel along the sides and top of the door. It contains wash water and steam to help prevent front leaks and ensure proper door compression.

• Seals the gap between the door and tub on the sides and top
• Helps stop water drips at the front corners and along the door edge
• Reduces escaping steam and moisture at the door area
• Common signs of wear: leaks from the door, visible tears/flattening, musty odor, or the door not sealing smoothly

• Disconnect power and turn off the water supply before servicing
• Open the door, pull the old gasket straight out; clean the channel of debris and residue
• Find the midpoint of the new seal at the top center and press it evenly into the channel down both sides without stretching
• Close the door to help seat the seal, then run a test cycle and check for leaks

This active carbon filter refreshes the air when your range hood is set to recirculate. Replace a saturated filter to restore effective odor reduction and maintain a more comfortable cooking space. What it does:

• Adsorbs cooking odors in recirculating operation
• Helps maintain fresher indoor air when venting back into the room
• Restores odor-removal performance when the old filter is saturated
• Typical signs it's time to replace: persistent cooking smells or diminished odor reduction

• One activated carbon filter

• Disconnect power to the hood before servicing
• Remove the metal grease filter(s) to access the charcoal filter
• Release the old filter from its clips/bayonet mount and install the new filter in the same orientation until it locks
• Charcoal filters are not washable; replace when saturated

• For hoods configured for recirculation; not used when vented to the outdoors

Secures components inside the freezer compartment. Replace if broken, cracked, or missing to keep parts properly positioned during door operation.

This sensor monitors operating conditions inside the appliance and reports to the control so cycles run correctly and safely. When the sensor fails, the control may receive inaccurate feedback, leading to irregular performance. What it does:

• Detects key conditions inside the appliance and sends a signal to the control
• Helps the control regulate heat and cycle progress
• Failure symptoms can include erratic cycle times, poor heating performance, or sensor-related error messages
• Can prevent the appliance from starting or completing a cycle if readings are out of range

• 1 sensor

• Disconnect power before servicing; shut off water supply if applicable
• Access the sensor and note wire orientation before removal
• Ensure any sealing surface is clean and the sensor is seated properly; check for leaks after reassembly where applicable
• Run a diagnostic or test cycle after installation to clear errors and verify operation

This temperature limiter safeguards the evaporator defrost heater by opening the circuit if temperatures rise too high. Replacing a failed limiter restores defrost safety and helps prevent frost buildup and inconsistent cooling performance.

• Protects the defrost circuit by cutting power to the evaporator heater when an over-temperature condition is detected
• An open/failed limiter prevents the heater from energizing, causing frost accumulation on the evaporator and warm refrigerator temps
• Designed to be installed in the original location and orientation for accurate temperature sensing

• Disconnect power before servicing; evaporator fins and sheet metal are sharp—use cut-resistant gloves
• Access the evaporator compartment and note the limiter's original mounting and wire routing before removal
• Transfer any clips/insulation sleeves and reconnect wiring to the same terminals; do not bypass this safety device
• Reassemble, restore power, and monitor for normal defrost operation

Inline connector that joins internal water hoses in your refrigerator. Replace if leaking or connections are loose to restore sealed fit. Confirm compatibility.

Secures shelves, door bins, and internal components in your bottom-mount refrigerator. Replace this clip if it's cracked, broken, or missing to restore stability.

Fixes ice buildup on evaporator coils and poor cooling. This defrost heater melts frost during the defrost cycle to restore airflow and temperature control.

Secures the water filter in your refrigerator for a snug, leak-free fit. Replace if lost during filter changes, cracked, damaged, or worn out over time.

This is a replacement micro switch used in select Bosch-built appliances. It opens and closes an electrical circuit when actuated by a lever or cam, enabling functions like starting/stopping a cycle or detecting a position.

• Controls power or signals by opening/closing a low-voltage circuit when pressed
• Commonly used for on/off, door/lid, or position-sensing functions
• Failure may cause the unit not to start, intermittent operation, or features that won't engage
• May also present as unresponsive buttons or functions that only work when pressed a certain way

• Disconnect power before servicing; verify no voltage is present
• Access location varies by model; remove panels as needed to reach the switch
• Note wire positions and terminal orientation before removal
• Test continuity with a meter after installation to ensure proper operation