Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
The Selector Knob is an OEM part for GE washing machines. This knob is used to choose different wash cycles and settings on the control panel, allowing users to customize their laundry preferences. It is designed to fit securely onto the control shaft and provide smooth operation for selecting various options.
Over time, selector knobs can wear out or become damaged due to frequent use or accidental impacts. Causes of a bad selector knob can include cracked or broken plastic, stripped or worn-out internal components, or a loose fit on the control shaft.
Symptoms of a bad selector knob include:
This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
I ordered a new knob and it arrived very quickly. The repair was simple and I will use appliance parts pros again should I need to. Thank you. Read more
The washer start stop switch button is the physical push button on your washing machine's control panel that signals the machine to begin or pause a cycle. It connects to the underlying switch mechanism that sends an electrical signal to the control system. Replace this part when pressing the button does nothing, the button feels mushy or broken, or the washer will not start or stop responding to that control.
All I had to do was remove 3, 1/4" screws from the back and take the front off. Two 5/16th screws hold the circuit board in place, remove them and press the button into the hole from the back. Replace the circuit board, slide the front back on and install the three 1/4" screws. Always unplug the washer first! Read more
Fix a washer that won't spin or agitate. This motor capacitor stores energy to start and run the motor. DIY repair takes about 10 minutes with video help.
Washer would run through the cycle, but not agitate. I had to wait for it to pump down the water level to check spin, which also was not working. The motor would buzz when it should run, but not rotate, hard to hear for spin because the pump was running. Found I could start it by hand very easily by giving the pulley a spin, so I figured start switch, but there didn't appear to be one. I found what looked like a start capacitor zip tied to the chassis midway up the front, so my second guess was... Read more
Drain pump inlet hose for top-load washers. Connects the tub to the pump assembly. Replace if cracked, leaking, or has holes causing water on the floor.
The video was very helpful. the hardest part is getting off old rusted parts. I had to use a hacksaw to remove one of the old clamps. I had to open the bottom of the washing machine to remove of the other clamp. Putting the new parts on was easy. Getting everything apart was a challenge. Putting the new parts on was an easy 5 minute job. Read more
Fabric softener not dispensing or agitator loose? This washer dispenser cup sits atop the agitator. Simple DIY fix—twist off and replace in minutes.
Planning to spend hundreds on a new washer and was pleased to discover the agitator coupling was the only thing wrong. Very easy repair. The only additional feature we would have liked was a softener dispenser. Located a GE model of the same genre that used the same coupler and took the leap to get the agitator and dispenser cup for this model (WJRR4170). Replaced the old agitator with new one and dispenser cup. Worked perfectly! We now have a washer with dispenser that works great and saved... Read more
Suspension rod and spring assembly for washer drum stability. Replaces worn, broken, or weakened suspension components causing drum movement or sagging.
I have a 14 year old GE washing machine that had been making a lot of noise while running but had eventually just stopped flat. The agitator and spin cycle would not run. I found this site and made excellent use of all the repair videos to study about my issue. I put in my machine model number and I Immediately was able to start honing in on what my problem could be from website advice about popular repair parts, stories others had shared about their similar machine issues and watching videos,... Read more
The Mode Shifter & Shaft Assembly is an OEM replacement part for GE washing machines. It is a mechanical component located inside the washer tub that allows for shifting between agitation, spin, and other cycles. The mode shifter and shaft assembly receive input from the control system to precisely change the operational mode at designated points in the cycle. Causes of a bad mode shifter & shaft assembly include worn out or damaged internal gears, stripped or broken shafts, or a loss of integrity in components that restrict smooth shifting between modes. Symptoms of a bad mode shifter & shaft assembly include:
This GE OEM replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
Motor control board was flashing 4 times, indicating that the mode shifter had an error. I disconnected the mode shifter's wire from the controller and measured the resistance between the 2 leads with an ohmmeter. Since the reading was infinite, that meant that the mode shifter coil or in-line thermal sensor was electrically open, i.e. bad. As this fix is near a complete tear-down of the washing machine, here are a few tips I discovered. 1) the hub nut is difficult to remove and you need a... Read more
Installation tool designed for installing washer drive belts. Provides proper leverage and positioning to seat belts correctly on pulleys and motor shafts.
Suspension rod and spring assembly supports the washer tub and reduces vibrations. Replace if cracked, worn, or broken to restore proper tub support.
I replaced all 4 suspension rods and springs and now it spins very smooth. They weren't broken, just badly worn. It gave new life to my 15 year old GE Profile washer. They are basically springs, so they wear after a while. It was well worth the hour I spent fixing it. You need a good long reach to get to the back 2 and you have to take off the dampening straps and the control panel so you can gain access. All in all, I'm happy with the repair, although I though that these parts are bit... Read more
Washer won't spin or agitate? A faulty lid switch magnet may be the cause. This part signals the switch that the lid is closed. Easy 20-minute DIY fix.
Replaced lid switch and lid magnet. Took just a little longer then 20 minutes as I had to splice in the new lid switch as it wasn't one that was a clip in, it was hard wired in. Read more
The GE screw is an OEM replacement part responsible for securing various components or parts together on a washing machine. Its main function is to connect and hold together various parts, panels, or brackets, ensuring that they remain securely in place during the appliance's operation. The screw comes in the size 1/4-20 MCH HXW 5/8 S, indicating its thread size, head type, and length.
This part fixes the following symptoms:
The GE washing machine screw can also be used on Hotpoint, RCA, and Kenmore/Sears appliances.
My husband put the new agitator together and it is working great, thanks for having all the part I needed. Susie Read more
Guides water from the inlet valve into the wash tub. Replace if cracked, broken, leaking, or causing uneven water distribution in your top-load washer.
Replaced the hose and water inlet. Part #: AP3189243 (WH41X10077). This connects the solenoid valves to bring water into the tub. Read more
If your washer agitator is exposed or collecting debris, this cap seals the top opening. Quick snap-on install in minutes—no tools required.
Plastic support bracket that secures suspension rods to the washer cabinet. Replace when cracked, broken, or worn to restore proper drum suspension.
Fix grinding or scraping noise during agitation with this washer pulsator coupling. Located under the agitator, connects to drive shaft. DIY repair in 10 minutes.
I looked up a YouTube video first to know how to take my washing machine apart. It was an Appliance Parts Pros Video. Very helpful! I replaced the mode shifter, water pump, washers, agitator spline, hub nut, tub bearing, tub seal and drive belt. The hub nut DID NOT want to come off. I cut it off with my Dremel and chipped out the beveled segment with a heavy duty screw driver and 3# hammer. Had to be very careful to not damage the hub assembly. I removed the Torx screws and removed the... Read more
Fix slow-filling or constantly running water issues with this washer water inlet valve. Controls hot, cold, and warm water flow. DIY repair in 30-60 minutes.
Replaced inlet valve Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.