Wdf53paym0 Parts

Color: Grey. 4oz bottle with brush used for touching up damage to your dishracks. For blue use W10840471. For white use WP676453. For tips use 676458.

This pocket-style door handle provides the recessed grip used to open and close the appliance door. Replacing a cracked or missing handle restores a clean look and a secure, comfortable grasp for everyday use. What it does:

• Provides a built-in finger pocket for reliably opening and closing the door
• Replaces a broken, cracked, loose, or missing handle
• Helps resolve difficulty gripping the door or sharp/rough edges from damage
• Maintains proper look and prevents stress on adjacent trim or panels

• 1 pocket-style door handle

• Disconnect power to the appliance before servicing.
• Open the door and remove the screws/clips retaining the old handle; note orientation and placement.
• Reuse the existing fasteners/brackets as required and align the new handle carefully.
• Tighten fasteners snugly without overtightening; verify smooth door operation.

Color: White. 4oz bottle with brush used for touching up damage to your dishracks. For blue use W10840471. For grey use WP676455. For tips use 675679

This dispenser water tube routes water from the inlet to the refrigerator's in-door dispenser manifold, helping ensure a steady, leak-free flow to the dispenser.

• Directs water from the supply line to the dispenser manifold
• A damaged or cracked tube can cause leaks, low/erratic dispenser flow, or air in the water line
• Replacing a leaking tube can help restore normal dispenser operation and prevent water damage

• Unplug refrigerator and shut off water supply before service
• Have a towel/container ready to catch residual water
• Note tube routing and connections; push-to-connect fittings may require firm seating for a watertight seal
• After installation, turn water on and check all joints for leaks

This heater terminal nut fastens the heating element's electrical connector to its stud, keeping the connection tight under heat and vibration. Replacing a worn or missing nut restores safe contact and consistent heating performance.

• Secures the wire/ring terminal to the heater stud for a solid electrical connection
• Helps prevent arcing, discoloration, and heat damage from a loose connection
• Signs include a loose terminal, burnt odor, or melted/charred insulation at the heater connection

• Disconnect power and allow the appliance and element to cool completely before service
• Photograph wiring for reference; remove old hardware and clean the terminal
• Inspect the ring terminal, insulators, and stud; replace any heat-damaged components
• Start threads by hand to avoid cross-threading; snug with the correct nut driver—do not overtighten

This factory-spec screw secures panels and components in your appliance. Replacing a missing or stripped fastener restores a tight, rattle-free fit so parts stay aligned and operate as designed.

• Fastens brackets, panels, and internal components to their mounting points
• Maintains alignment and reduces vibration during operation
• Replaces missing, worn, rusted, or stripped hardware
• Helpful when you notice rattling, loose panels, gaps, or parts shifting out of position

• Disconnect power; shut off water or gas supply if applicable
• Align the part being secured and remove any damaged hardware
• Hand-start threads to avoid cross-threading; tighten with the correct driver
• Do not overtighten; verify the assembly is secure and operates freely

Bottle with brush. Color: Black. Size: 0.6 fl.oz.

This tub insulation shield mounts at the front/base of the dishwasher tub to cover and secure the sound-dampening insulation. It helps protect the insulation from splash and wear so the blanket stays in place for quieter operation. What it does:

• Covers and protects the tub's insulation from moisture and abrasion
• Helps keep insulation properly positioned for sound and thermal performance
• Direct replacement for a cracked, warped, or missing shield
• Typical symptoms: exposed or sagging insulation, louder operation, or difficulty fitting the toe panel

• 1 tub insulation shield

• Disconnect power and shut off the water supply before servicing
• Remove the lower toe panel/kickplate to access the shield area
• Position insulation correctly, then install the shield using the existing mounting points/hardware
• Reinstall the toe panel and test for proper fit and operation

This heater support holds the heating element securely in place inside the appliance, maintaining correct alignment and clearance for reliable operation. Replacing a worn or broken support helps prevent sagging, noise, or damage from an out-of-position element.

• Secures the heating element to its mounting point to keep it stable
• Maintains proper spacing from nearby components and surfaces
• Helps reduce vibration, rubbing, or rattling noises
• Replace if the original support is cracked, warped, missing, or the element appears misaligned

• Disconnect power to the appliance before servicing; allow hot components to cool
• Access the heater per your model's service information; note the original orientation and routing
• Seat the support fully and handle element leads carefully to avoid damage

This replacement shield fits over the heater/probe area to provide a protective barrier. It helps prevent direct contact and excessive radiant heat exposure, protecting nearby components and supporting accurate temperature sensing for consistent operation. What it does:

• Shields the heating element and adjacent temperature probe/sensor area
• Helps prevent heat damage to nearby plastics, wiring, and components
• Reduces the chance of items contacting or striking the heater/probe
• Common signs it's needed: cracked, warped, or missing shield; discoloration; rattling or an exposed probe/heater area

• 1 shield

• Disconnect power and allow all heated parts to cool before servicing
• Access the heater/probe area and note the original shield orientation
• Seat the shield fully; secure with existing clips/fasteners if applicable
• Verify clearances around the heating element before restoring power

Color: light gray. Measures about 3 inches high by 6 inches deep.

Bushing, Door spring

Color: White

This passive vent assembly allows moist air to escape during the dry cycle, helping reduce steam and moisture inside the dishwasher tub. Replacing a warped or leaking vent can improve drying performance and prevent moisture from seeping onto the door panel.

• Allows steam to vent from the tub without a fan
• Helps reduce condensation and moisture buildup during drying
• Common fix for visible steam leaks at the door, moisture on the console, or poor drying results
• Restores proper air path through the door vent channel

• Disconnect power and shut off water supply before servicing
• Access is typically from the inner door; remove the inner panel to reach the vent
• Inspect and replace any damaged gasket or door insulation as needed
• Ensure the vent seats evenly and fasteners are snug to prevent leaks

This surface burner gas manifold assembly routes gas from the supply to each burner on your range or cooktop. Replacing a worn or damaged manifold restores safe, consistent gas flow and reliable burner operation.

• Distributes gas evenly to the surface burners via the manifold rail
• Serves as the mounting/connection point for the burner control valve bodies
• Common symptoms include burners not lighting, low or uneven flames, or a gas odor near the control area
• Restores proper gas delivery after damage, corrosion, or impact to the original manifold

• Disconnect electrical power and shut off the gas supply before servicing.
• Take clear photos and label all connections to ensure correct reassembly.
• Use only gas-rated thread sealant where specified by the manufacturer and tighten fittings securely.
• After installation, restore gas and check all joints with a leak-detection solution; verify every burner ignites and flames are stable.

Size: 1/4 inch hex head, 10-12 x 1/2 inch.