Wdt920sadmo Parts

This replacement wire restores a reliable electrical path between appliance components. Use it to replace a damaged or heat-stressed lead so power or signal can flow correctly for consistent, safe operation.

• Carries electrical power or signals between components to restore continuity
• Helps resolve issues caused by broken conductors, loose/burned terminals, or brittle insulation
• Can address intermittent operation or components not energizing due to an open circuit
• Ideal when the original lead shows scorching, melting, or corrosion

• Disconnect power (and shut off gas/water if applicable) before servicing
• Document wire routing and connections before removal to ensure correct reassembly
• Transfer any reusable sleeves, clips, or ties from the old lead if present
• Seat connections fully and route the wire away from sharp edges and high-heat areas

This cup shelf clip secures the dishwasher's fold-down cup shelf to the upper rack. Replacing a cracked or missing clip restores a stable shelf so cups and small items stay organized throughout the wash cycle.

• Fastens the cup shelf to the upper rack wire to prevent wobble or detachment
• Helps the shelf pivot and lock properly when raised or lowered
• Typical symptoms: shelf hangs loose, falls off, won't stay in position, or the original clip is broken/missing

• Open the door and fully extend the upper rack; remove the rack if needed for access
• Squeeze the old clip's tabs to release and lift it off the rack wire or shelf
• Align the new clip on the rack wire and press until it snaps securely into place
• Verify the shelf moves and locks correctly before running a cycle

Bottle with brush. Color: Black. Size: 0.6 fl.oz.

This compression tube nut secures water inlet tubing to a threaded fitting to create a reliable, leak-resistant seal. Replace a cracked or stripped nut to stop drips at the connection and keep your appliance's water system working properly.

• Compresses the tubing against the fitting to seal the water line at the inlet valve, filter head, or other water-system connections
• Helps correct leaks at the water line connection point
• Replaces nuts that are cracked, cross-threaded, or deformed
• Common symptoms: water dripping at the connection, difficulty tightening the line, or a poor seal after reassembly

• Shut off the water supply and disconnect power before servicing.
• Slide the nut onto the tubing first, seat the tube fully on the fitting, then hand-tighten and snug with a wrench; do not overtighten.
• Inspect and reuse the existing sleeve/ferrule and tube insert if in good condition; replace if worn.
• Restore water and check for leaks at the connection.

The door balance mount is the side-frame bracket that supports the dishwasher's door counterbalance system. When worn or broken, it can let the door drop, slam, bind, or feel heavy. Replacing it restores smooth, controlled door movement. What it does

• Anchors the door springs and balance link/cable to counterbalance the door's weight
• Helps the door open and close smoothly without dropping or slamming
• Guides the balance link for consistent, quiet movement
• Common symptoms: door feels heavy or uneven, falls open, won't stay put, or makes grinding/squeaking noises; visible damage to the bracket or rollers

• One door balance mount (bracket)

• Disconnect power and shut off water before servicing
• Pull the dishwasher out slightly to access the side where the mount is installed
• Carefully relieve spring tension; note link/cable routing before removal
• Transfer the spring/link to the new mount, secure the bracket, and check door balance on both sides

This inner door seal forms a moisture barrier between the dishwasher tub and the door assembly, helping keep wash water and steam contained. Replacing a worn seal can stop drips at the door and protect internal components.

• Seals the joint along the inner door to contain wash water and steam
• Helps prevent door-area leaks or drips during cycles
• Blocks moisture from entering the door cavity where electrical parts reside
• Common signs: water at the bottom/sides of the door, damp control area, visible wear/flattening or tears on the seal

• Disconnect power and turn off water supply before servicing
• Open the door and remove perimeter screws to separate inner/outer door panels
• Remove the old seal; clean the mounting surface and note seal orientation
• Press the new seal firmly into place, reassemble, and run a leak check

The Rack Adjuster Housing is an OEM part for Whirlpool built-in dishwashers. It is located internally and provides secure mounting of the rack height adjustment mechanism.  

Causes of a faulty rack adjuster housing include wear and fatigue from cycles of repeated rack extension and retraction movements during normal use. Damage from impact during cleaning is also possible.

Symptoms of a bad rack adjuster housing include:

• The lower rack fails to raise or lower properly 
• Difficulty setting the rack at different height positions
• Excessive noise or vibration from a loose mounting

This OEM replacement is compatible with additional Whirlpool, KitchenAid, and some Jenn-Air built-in dishwasher models.

This replacement screw secures appliance components, panels, and brackets. It restores a tight, reliable hold when an original fastener is missing or damaged, helping eliminate rattles, gaps, or shifting parts.

• Fastens two or more parts together inside the appliance
• Helps keep panels, brackets, or trim securely in place
• Can reduce vibration, rattling, or loose handles caused by missing/loose screws
• Replaces worn, stripped, or corroded fasteners

• Disconnect power and shut off water supply before servicing
• Match location and orientation to the original fastener
• Start threads by hand to avoid cross-threading; use the correct driver bit
• Tighten snugly—do not overtighten to prevent stripping or cracking

Size: 1/4 inch hex head, 10-12 x 1/2 inch.

This replacement OEM part is a sump and motor assembly for dishwashers. The sump and motor assembly distributes water to the spray arm of the dishwasher. Luckily, replacing this part is a simple process. To begin, turn off the power supply and shut off the water supply valve. Remove the screws that secure the lower access panel. Disconnect the water supply line from the inlet valve. Then proceed to remove the mounting screws from the junction box cover. Take note of the wires' orientation. Remove the screws that hold the bracket. Disconnect the drain hose from the sink or garbage disposal. Open the dishwasher door and remove the mounting screws. Pull the dishwasher away from the cabinet and unsnap the covers from the hinge ropes. Disconnect the ropes. Remove the screws securing the upper door panel. Carefully tilt the dishwasher back and detach the fill hose from its retaining clip disconnecting the hose from the sump. Uninstall the sump and motor assembly and align the pump with the seal and sump. This genuine replacement part is sold individually and is compatible with Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Sears/Kenmore brand dishwashers.

This rear support wheel replaces a worn roller that helps a sliding drawer or rack glide smoothly and stay aligned. Restores easy, even movement and reduces dragging, scraping, or tilting during everyday use.

• Supports the rear of a sliding assembly on its track
• Provides smooth rolling action and helps maintain alignment
• Helps prevent binding, popping off the track, or uneven travel
• Replace if the wheel is cracked, flattened, missing, or if movement is noisy or difficult

• Disconnect power before servicing; allow the appliance to cool
• Remove the sliding assembly to access the wheel area
• Transfer or reinstall any axle/retainer from the original wheel as needed
• Verify smooth travel and proper alignment after replacement

Includes vinyl rack repair touch up paint and tine tip covers. Color: Grey

This manifold channels wash water to the dishwasher's spray system for full coverage. Replacing a cracked or warped manifold restores proper water flow and wash performance while helping prevent leaks at the feed connection.

• Directs recirculated water from the pump to the spray arms/feed tube
• Maintains a sealed path to keep spray pressure consistent
• Damage can cause poor cleaning, weak spray, unusual noise, or internal leaks
• Cracks or broken tabs can leave spray arms misaligned or not spinning

• Disconnect power and turn off the water supply before servicing
• Open the tub; remove the lower rack and spray arm as needed for access
• Transfer any seals/O-rings or clips from the old part; seat all connections fully
• Run a short test cycle and check for leaks before reassembling

This hose clamp secures dishwasher hoses to fittings and ports to maintain a tight, leak-resistant seal. Replacing a worn clamp helps prevent drips and loose connections that can cause water under the unit.

• Secures drain or circulation hose to the pump, sump, or other dishwasher fittings
• Helps maintain a watertight seal at hose connection points
• Can help resolve water dripping from a hose joint or a loose hose
• Replace if corroded, deformed, cracked, or no longer holds tension

• Disconnect power and turn off the water supply before servicing
• Place a towel or shallow pan to catch residual water when removing hoses
• Fully seat the hose on the fitting, position the clamp over the barb/connection, and secure firmly
• After reassembly, run a brief fill/drain and check all connections for leaks

12 Ft in length

This replacement mounting screw secures appliance components and panels. When original hardware loosens, strips, or goes missing, installing a new screw restores a snug, rattle-free fit and keeps assemblies properly aligned for reliable operation.

• Fastens brackets, covers, or internal components to the appliance frame
• Helps maintain alignment of panels, trims, and assemblies
• Replaces stripped or corroded hardware to reduce vibration, noise, or gaps
• Common signs it's needed: missing/loose screw, stripped head/threads, panel movement or rattling

• Disconnect power and shut off gas/water supplies before servicing
• Use the correct driver bit; start threads by hand to avoid cross-threading
• Repair/replace damaged clips or inserts before tightening
• Tighten snugly; avoid overtightening into plastic or thin sheet metal