Wfl2060uc Parts

This interference capacitor suppresses electrical noise and radio-frequency interference to help the appliance's electronics run more reliably. It fits on the control board and supports stable operation by filtering stray voltage spikes. What it does:

• Filters electrical and radio-frequency interference that can cause erratic control behavior or false error codes
• Reduces electrical noise that can affect nearby audio or radio reception
• Helps protect control circuitry from transient voltage spikes
• Commonly used when appliance exhibits intermittent faults or unexplained control glitches

• Disconnect power to the appliance before starting any repair
• Discharge capacitors and avoid touching leads; use insulated tools and follow safe-handling practices
• Replace only with the exact part specified for your model and secure all wire connections firmly

This rubber sealing ring replaces a worn or damaged seal to help stop water leaks and maintain a tight fit where two appliance parts meet. It's a direct-fit replacement designed for reliable sealing performance. What it does

• Creates a watertight barrier at the mating surface to prevent leaks and drips
• Restores proper sealing pressure when the original seal is cracked, flattened, or brittle
• Helps prevent water damage and maintains appliance efficiency by stopping unintended water escape
• Common symptom: visible leaking, dripping, or moisture collecting near a joint or connection

• One rubber sealing ring

• Disconnect power and shut off water supply before starting any repair
• Remove the old seal completely and clean mating surfaces of debris, residue, or mineral buildup
• Inspect the mounting area for damage; replace any damaged components before installing the new seal
• Press the new seal evenly into place; test for leaks by running a short cycle and checking the connection

A front lower trim piece that finishes the base of the washer and helps protect the cabinet opening from debris. Replaces a cracked, dented or missing toe kick to restore a clean appearance and proper fit at the washer's base. What it does

• Covers and protects the washer's lower front opening from dust and small debris.
• Restores the factory appearance when the original toe kick is damaged or missing.
• Helps reduce visible gaps that can catch lint or small items.
• Stops rattling or loose fit at the base when the original piece is bent or broken.

• One front lower toe kick panel (single piece as shown)

• Disconnect power and water before doing any service that requires removing panels.
• Access typically requires removal of the lower access panel or front service panel—keep small fasteners in a secure place.
• Handle edges carefully to avoid cuts; use gloves if needed.

This dispenser tray replaces the plastic cup that holds detergent and rinse agent inside the dishwasher dispenser assembly, restoring proper detergent placement for even cleaning and reduced residue. What it does:

• Holds detergent/rinse agent in the dispenser so it releases during the wash cycle
• Ensures proper alignment with the dispenser cover and release mechanism
• Helps prevent detergent from pooling or leaving residue on dishes when cracked or warped
• Restores correct dispenser function when the original tray is damaged or missing

• Disconnect power to the appliance before beginning any repair.
• Remove the inner door panel or dispenser bezel per your model's service instructions to access the tray.
• Replace the tray by seating it into the dispenser housing until it snaps or aligns in place; avoid forcing parts.
• After reassembly, run a short cycle to ensure proper detergent release.

This replacement drum is the rotating tub that holds and tumbles laundry inside the dryer, restoring proper airflow and garment movement for efficient drying. It installs in the dryer cabinet and works with rollers, belts and the motor assembly. What it does:

• Provides the rotating surface that tumbles clothes for even drying
• Maintains proper spacing for airflow to help prevent overheating and uneven drying
• Replaces a cracked, dented, or warped drum that can catch or damage fabrics
• Stops metal-on-metal or scraping noises caused by a damaged drum surface

• Disconnect power (and gas supply if applicable) before starting work
• Replacement requires partial disassembly of the dryer cabinet; inspect rollers, belt and seals while open
• Handle carefully to avoid sharp edges and protect the drum finish

This rear drum motor mounting bushing supports the motor shaft at the back of the tub, keeping the drum aligned and reducing wear. It restores smooth drum rotation and helps reduce noise and vibration when functioning properly. What it does:

• Centers and supports the motor shaft to maintain proper drum alignment.
• Cushions rotating components to reduce squealing, grinding, or scraping noises.
• Helps prevent excess drum wobble and uneven wear on the tub and bearings.
• Can stop intermittent rubbing or burning smells caused by a worn mounting surface.

• Disconnect power before starting and follow all safety precautions; service panels may have sharp edges.
• Access typically requires removing the dryer/heater assembly and drum.
• Inspect mating surfaces and surrounding components (shaft, bearing, seal). Replace any excessively worn parts to prevent repeat failures.
• Use only OEM-recommended parts and fasteners; do not force or press the part in without proper alignment.

This spring-tank is the replacement spring assembly used to restore proper door balance and movement. It helps the appliance door open and close smoothly and prevents sudden drops or heavy lifting. What it does

• Provides counterbalance tension for the appliance door to control opening and closing motion
• Reduces sagging or slamming of the door caused by worn or broken springs
• Restores smooth, even movement when the door feels heavy or uneven
• Works as a direct-fit replacement when the original spring assembly fails

• One spring-tank

• Disconnect power and water to the appliance before starting any repair
• Handle spring components carefully; springs are under tension and can cause injury if released unexpectedly
• Use proper tools and follow manufacturer instructions or a service manual for safe removal and installation

This dishwasher sump assembly houses the pump inlet and integrated ball check valve to route wash water to the drain while preventing backflow. Replaces worn or cracked sumps to restore proper draining and prevent leaks. What it does

• Collects and channels dishwasher wash water from the tub to the drain pump.
• Integrated ball check valve stops backflow into the sump, helping prevent standing water and odor.
• Restores proper drain function when the existing sump is cracked, clogged, or leaking.
• Compatible with common Bosch/BSH dishwasher pump systems that use a molded sump with ball valve.

• One sump with integrated ball check valve (single assembly only).

• Disconnect power and water supply before starting any repair.
• Access typically requires removing the dishwasher lower kickplate and possibly tilting the unit; support the unit and follow the OEM service manual.
• Inspect surrounding seals, hoses, and pump gaskets for wear and replace as needed.

This water level regulator controls the appliance's water fill by sensing and regulating pressure/level for proper operation. Replacing a failing regulator restores correct fill behavior and helps prevent over- or under-fill conditions. What it does:

• Senses water level/pressure and signals the fill system to start or stop water flow
• Prevents overfilling by stopping the inlet when the correct level is reached
• Helps avoid underfilling that can cause poor wash or rinse performance
• Resolves symptoms like continuous filling, no fill, or erratic water levels

• Water level regulator

• Disconnect power and turn off the water supply before attempting replacement
• Handle electrical connections and hoses carefully; note wiring positions for reassembly
• Inspect hoses and seals for damage and replace if cracked or brittle
• Test the appliance through a short cycle after installation to ensure proper fill and operation

This fastening ring secures a rotating or stationary component in place to help prevent movement and vibration. It restores proper fit and alignment so assemblies run quietly and components stay locked in position. What it does:

• Holds shafts, bearings or housings in position to prevent axial movement
• Helps stop rattling, wobble or misalignment caused by a loose retaining component
• Maintains a secure mechanical connection between mating parts
• Used wherever a snap/retaining ring is required to lock a component on a shaft or in a bore

• Disconnect power and water before beginning any repair
• Use the correct pliers or tools for snap/retaining rings to avoid deformation
• Verify the ring matches the OEM part number and seating location before installation

This drain reservoir is the dishwasher plumbing housing that collects and directs wastewater to the drain pump, helping prevent internal leaks and ensuring proper draining. Replace a cracked or clogged reservoir to restore reliable water flow and reduce water under the unit. What it does:

• Funnels wastewater from the tub to the drain pump so the machine can evacuate used water
• Helps contain minor spills and prevents water from reaching sensitive electronics
• Works with the drain pump and hoses to maintain proper drainage
• Commonly causes water pooling under the dishwasher, slow or no drain cycles, or visible leaks when damaged

• Disconnect power to the appliance before starting any repair
• Shut off water supply and remove lower access panels or kickplate as needed
• Handle with care to avoid damaging adjacent hoses, clips, or wiring; replace any worn seals