Wfw95hexw Parts

This dishwasher detergent dispenser stores detergent and releases it at the correct time in the cycle for consistent cleaning results. Replacing a worn dispenser restores reliable dosing so each wash performs as designed. What it does:

• Holds detergent and keeps it contained until dispensing
• Opens the detergent cup door at the programmed time in the cycle
• Directs detergent into the wash stream for even distribution
• Helps prevent poor cleaning caused by early loss or failure to dispense

• 1 detergent dispenser assembly

• Disconnect power and turn off water supply before servicing
• Remove the inner door panel to access the dispenser; support wiring and insulation as you work
• Release mounting tabs/screws, transfer the wiring connector, seat the new dispenser evenly, and tighten fasteners uniformly
• Run a quick cycle to check for leaks

STACK KIT FOR LONG VENT DRYER

The Shipping Bolt Kit is an OEM part for Whirlpool washing machines, specifically designed to secure the appliance during transport. This kit includes several bolts that are crucial for immobilizing the washing machine's drum, preventing any movement that could lead to internal damage while the unit is being moved. This kit includes two front and two rear shipping bolts

Causes for replacing the Shipping Bolt Kit can stem from misplacing the original bolts after installation or the bolts becoming worn or damaged after multiple uses.

Symptoms of needing a Shipping Bolt Kit include:

• Preparing a washing machine for a move without the original bolts, risking damage to the unit
• Noticing previous shipping bolts are lost or damaged, requiring replacement for future transport

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This drum baffle mounts inside the rotating drum and lifts items so they tumble evenly through the cycle. Replace a cracked, loose, or missing baffle to reduce noise and restore consistent tumbling performance. What it does:

• Lifts and separates laundry as the drum turns for even tumbling
• Helps prevent clumping that can lead to poor results or longer cycles
• Maintains balanced drum movement; damage or looseness can cause rattling or scraping
• May help if items aren't tumbling well, you hear thumping, or garments snag inside the drum

• 1 drum baffle

• Disconnect power before servicing; for gas dryers, also shut off gas. For washers, turn off water supply.
• Open the door and rotate the drum to access the baffle's mounting screw(s).
• Remove the screw(s), disengage the baffle from its slots, and lift it out.
• Seat the new baffle in the slots and secure with the screw(s). Hand-spin the drum to confirm clearance before use.

This 2-pack of dryer vent clamps secures the vent hose to the dryer outlet and the wall/vent hood. A tight connection helps maintain airflow, reduce lint leaks, and keep the duct from slipping off during use.

• Tightens around the vent hose to hold it securely to the dryer exhaust collar or exterior vent
• Helps prevent hose detachment, air leaks, and lint escaping at the connection
• Supports proper exhaust airflow by keeping connections sealed and stable
• Common symptoms pointing to replacement: hose won't stay on, visible gaps or lint around fittings, rattling at the vent, or longer dry times from poor ventilation

• Disconnect power; for gas dryers, shut off gas supply before moving the appliance
• Slide a clamp over the hose, seat the hose fully on the collar, position clamp over the fitting, and tighten with a screwdriver or nut driver
• Do not overtighten; avoid crushing thin foil ducting; ensure the hose is straight and not kinked
• Restore power and verify strong airflow at the exterior exhaust

This replacement screw secures appliance components and panels so they stay aligned and rattle-free during operation. Replace stripped, missing, or corroded hardware to restore a tight fit and dependable performance. What it does

• Fastens brackets, panels, and internal sub-assemblies in the appliance
• Helps maintain alignment to reduce vibration and rattling
• Replaces missing, rusted, or stripped screws that no longer hold
• Useful when a part won't mount securely or a screw backs out during use

• One screw

• Disconnect power; for gas appliances, also shut off the gas supply
• Compare to the original for length and thread style for the location
• Start threads by hand to avoid cross-threading; use the correct driver bit
• Do not overtighten; if the mounting hole or clip is worn, replace it

This Dispenser Divider installs in the washer's detergent drawer to separate and control liquid or powder detergent in the main-wash compartment. Replacing a worn or missing divider helps restore proper dispensing and more consistent cleaning results.

• Sits in the main-wash section to select liquid or powder detergent
• Directs and regulates water flow for complete detergent siphoning at the right time
• Replaces a cracked, warped, or missing divider that can affect wash performance

• Disconnect power and turn off water supply before servicing
• Pull the dispenser drawer out and depress the release tab to remove it
• Lift out the old divider, clean the compartment, and snap the new divider in the correct orientation (liquid or powder as marked)
• Reinstall the drawer and run a short cycle to verify proper dispensing

Extends the drain hose approximately 4 feet. You must also order a drain hose connector kit: 285835.

Size: 1-1/16 x 5/8 inch. Used for fill hose. For a 4 pack order 285448A

This is the service tech sheet for the appliance. It provides wiring diagrams, diagnostic information, and troubleshooting procedures to help accurately identify and resolve performance issues.

• Contains official diagnostic steps and wiring information
• Helps trace error conditions and electrical problems
• Useful when the unit won't start, won't run cycles, or shows fault codes
• Supports accurate troubleshooting to reduce guesswork

• Disconnect power before servicing the product.
• The sheet is typically stored inside the appliance (often behind an access panel or in the door area).
• Handle with dry hands; avoid smudging or tearing diagrams.
• Re-secure in its original location for future service reference.

This is a replacement screw designed to work with a wide range of household appliances. It is used for many purposes in these appliances, from holding body panels together to securing electronics into control boards. However, screws are subject to damage through corrosion, impact, and improper installation/removal. In most cases, the primary damage to this screw is through corrosion – it may become rusted or corroded in place, depending on the appliance and the maintenance provided during its lifespan. The screw may also be stripped or rounded due to improper removal or installation. If the screw is damaged, lost, or corroded in place, it will need to be replaced. In most cases, removal will require nothing more than a Phillips head screwdriver or the appropriately sized socket with a ratchet. However, if the screw is damaged, it may require a tap set to remove it from its mounting location. Note that this is a genuine OEM replacement screw made from durable, high-quality metal, and is sold individually. It fits Whirlpool, Maytag, Roper, Estate, Amana, Crosley, and Thermador appliances. It is used in over 150 machines, ranging from washers and dryers to air conditioners.

Contains two, six foot long braided hoses with 90 degree ends.

This set of washer fill hoses connects your home's hot and cold water supply to the washer's inlet valves. Replacing aging hoses helps prevent leaks and ensures the washer fills properly for every cycle.

• Supplies hot and cold water from household faucets to the washer's inlet valves
• Helps address leaks, bulges, or cracks in old hoses
• Can resolve drips at fittings and water on the floor
• Improve slow or no-fill issues caused by kinks or internal blockages

• Unplug the washer and turn off both water supplies before starting
• Place a towel or pan to catch residual water; disconnect old hoses from faucets and inlet valves
• Attach new hoses to the correct hot/cold connections; tighten connections securely without overtightening
• Open valves, check for leaks at both ends, and re-tighten if needed

This RFI noise filter conditions the AC power entering your microwave, reducing electrical interference and helping protect and stabilize the control and power circuits. Replace it if the unit is dead or trips a breaker when starting.

• Filters radio-frequency/electromagnetic noise on the incoming AC line
• Helps stabilize power to the control, relays, lights, and fans
• Failure may cause no display or intermittent loss of power
• A shorted filter may blow the line fuse or trip the household breaker when plugged in or when Start is pressed

• Disconnect power by unplugging the microwave or switching off the dedicated circuit breaker
• For over-the-range units, remove the microwave from the wall to safely access internal components
• Label and transfer wires to matching terminals; mount the filter securely and route wiring away from sharp edges

Size: 29 1/4 inches x 31 1/4 inches. This universal washer drip tray is large enough for duet washers and sits under the washer to protect your floors from scuffs, spill, etc. Includes a PVC drain fitting.

This replacement screw secures panels, brackets, and internal components in your appliance. Replacing a missing or stripped screw restores a tight, rattle-free fit and helps keep parts properly aligned and protected during operation.

• Fastens appliance panels, brackets, and hardware in the designated locations
• Replaces missing, stripped, or corroded fasteners
• Helps reduce vibration noise and looseness from unsecured parts
• Restores proper fit and alignment after service or reassembly

• Disconnect power; turn off water supply before servicing
• Match the screw to the original location and replace one at a time to maintain alignment
• Use the correct driver; tighten snugly without overtightening to avoid stripping metal or cracking plastics
• If threads in the mating hole are damaged, repair/replace the clip or insert as specified in the service manual