Whirlpool Wtw7300dw0 Parts

Color: Grey

This set of washer fill hoses connects your home's hot and cold water supply to the washer's inlet valves. Replacing aging hoses helps prevent leaks and ensures the washer fills properly for every cycle.

• Supplies hot and cold water from household faucets to the washer's inlet valves
• Helps address leaks, bulges, or cracks in old hoses
• Can resolve drips at fittings and water on the floor
• Improve slow or no-fill issues caused by kinks or internal blockages

• Unplug the washer and turn off both water supplies before starting
• Place a towel or pan to catch residual water; disconnect old hoses from faucets and inlet valves
• Attach new hoses to the correct hot/cold connections; tighten connections securely without overtightening
• Open valves, check for leaks at both ends, and re-tighten if needed

Contains two, six foot long braided hoses with 90 degree ends.

The wire harness is an OEM part for Whirlpool washing machines. This harness is a network of color-coded wires that connect the machine's electrical control module to other components. It allows for the transmission of power and data necessary for operating wash cycle functions.

Causes stem from normal wear over time as wires endure constant motion during every cycle. Accidental cuts or exposed wires from damage can also cause failures.

Symptoms of a bad wire harness include:

• The washer not starting or only partially functioning
• Error codes displaying or cycles not completing properly
• Corrosion or physical damage seen on wire connectors

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

Used from harness to top.

The Screw is an OEM component compatible with Whirlpool washing machines. This screw secures the rear panel onto the cabinet frame, ensuring a sturdy connection between housing components.  Proper installation is critical for the washer's structural integrity.

Causes of a bad screw include corrosion from repeated water exposure or stresses from years of use. Loosening can occur from vibrations weakening the threads over time. 

Symptoms of a bad screw include:

• Rear panel detaching from frame opening gaps
• Increased noise and vibrations from a compromised seal  
• Stress on other connections from improper mounting points
• Potential leak paths from openings near hoses or tub areas

This OEM Whirlpool replacement screw helps maintain a tight panel closure. It is compatible with additional brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Lid Hinge (left) is an OEM replacement part for Whirlpool brand top-load washing machines. It is the hinge mechanism attached to the left side of the washer door assembly.

Symptoms of a bad hinge include: 

• Looseness, wobbling, or inability to securely support the weight of the washer door
• Strange noises or difficulty smoothly operating the door 
• Failure to keep the door fully open or closed
• Potential safety hazards if the door cannot be properly positioned

Causes involve wear and tear from repeated opening and closing of the washer door over many cycles, as well as damage from excessive weight loads placed on the door over time.

This Whirlpool replacement part is also compatible with Maytag, KitchenAid, and select Kenmore models.

This replacement nut secures appliance parts and hardware to keep assemblies stable and prevent loose connections. It's a simple, direct replacement for worn or missing fastening hardware to restore proper fit and reduce vibration. What it does:

• Fastens mounting studs, brackets or panels to hold components in place
• Restores secure mechanical connections that can loosen over time
• Helps eliminate rattling, vibration and misaligned panels caused by missing or stripped hardware
• Provides a straightforward, durable replacement for corroded or damaged nuts

• Disconnect power to the appliance before beginning any repair
• Use the correct-size wrench or socket; ensure threads engage smoothly before tightening
• Tighten until snug—avoid overtightening that can strip threads or damage components
• Inspect mating threads and replace any damaged studs or hardware for a reliable repair

Size: .20 Fl. Oz. (6 ml)

This factory washer is used in appliance assemblies to distribute load under a fastener and maintain a secure, accurate fit. Replace a missing or damaged washer to restore proper stack-up and reduce vibration, noise, or loosening.

• Distributes load and provides proper spacing in the fastener assembly
• Helps keep bolts, screws, or nuts tight to minimize vibration and rattling
• Direct replacement when the original washer is worn, bent, cracked, or missing
• Typical signs include loose panels/brackets, recurring looseness after tightening, or new vibration after service

• Unplug the appliance; shut off water supply if working near hoses or valves
• Note the original hardware stack-up and reassemble in the same order
• Inspect mating surfaces and companion hardware; replace any damaged parts
• Tighten fasteners snugly per service guidance; avoid overtightening

Replace aging or leaking washer supply lines with this fill hose kit. It provides two 5-foot hoses to connect your home's hot and cold water valves to the washer, helping maintain a secure connection and consistent filling.

• Connects hot and cold water faucets to the washer's inlet valves
• Replace if hoses are leaking, cracked, bulging, or kinked
• Can help address slow filling caused by restricted or kinked hoses
• Useful when installing or relocating a washer

• Unplug the washer and shut off both water supply valves before starting
• Place a towel or pan to catch residual water; disconnect old hoses from faucet and washer
• Match hot to hot and cold to cold; hand-start threads to avoid cross-threading, then tighten firmly without overtightening
• Restore water and power; run a fill test and check all connections for leaks

The Tub Ring is an OEM component for Whirlpool washing machines. It is a rubber or plastic ring that fits snugly within the metal wash tub to create a protective seal. 

The tub ring prevents leakage, provides noise dampening, and distributes rotational forces evenly across the tub base during spin cycles. Its durable construction withstands continuous agitation and movement.

Causes for a bad tub ring include cracking or splits that compromise the seal over time. Foreign objects like coins or fasteners left in pockets could puncture the ring.

Symptoms of a bad tub ring include:

• Puddling, leaks, or drips under the washer after use  
• Vibrations transfer more noticeably through floors
• Higher water levels than normal required 
• Soap scum builds up around the base over multiple loads

This OEM part is also compatible with washing machines from Maytag, KitchenAid, Jenn-Air, and Kenmore.

This machine screw secures components in place to maintain proper alignment and stability during appliance operation. Replacing a worn or missing screw restores a tight fit and helps prevent vibration, noise, or loosening parts.

• Provides a secure mechanical fasten for panels, brackets, or internal assemblies
• Helps correct rattling, vibration, or loose-fitting parts
• Useful when an original screw is stripped, corroded, or lost
• Sized to match 8-18 thread applications in compatible units

• Disconnect power and shut off water or gas before servicing
• Note original screw location and orientation for correct reassembly
• Start threads by hand to avoid cross-threading; do not overtighten
• Replace any damaged clips or mounts the screw engages

Color: Gray. Size: 13 oz. can. Used for coating the dryer drum interior. Acrylic appliance paint.

Right Side

The Lid Hinge is an OEM part for Whirlpool washers. This hinge connects the washer lid to the cabinet and allows it to safely and securely open and close during operation.

The hinge is responsible for providing a smooth, controlled movement as well as properly securing the lid in place when closed. It ensures proper operation and functionality of the washer by facilitating easy access for loading and unloading clothes.

Causes of a bad hinge can include wear and tear over time, unbalanced loads that put excessive strain on the hinge components, or damage from impact or overextending the lid.

Symptoms of a bad hinge include:

• Difficulty opening or closing the washer lid
• The lid not staying securely closed or popping open during cycles
• Noises or squeaks coming from the hinge area
• The hinge hanging loose or off-track

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

5 foot. Package of 2.