Need Help?
Call
Secures and protects your microwave's interior lamp assembly. Replace if cracked or heat-damaged to restore stable bulb fit and lighting. Confirm compatibility.
Power cord connects your microwave to the wall outlet. Replace if damaged, frayed, chewed, or cut. Attaches to internal wiring with wire connectors.
The grill vent is only held in place by two screws. Super simple fix. Remove the two screws and the old grill vent, position the new vent and put the two screws back in. Replacing the cord required that cabinet to be removed. Lots of screws on the back, top and bottom. Once the screws were removed, the cabinet pulled back. The power cord connections were then clearly visible. Undid the two wire connectors and unscrewed the ground wire from the body to remove the old power cable. Installed the... Read more
Replacement mounting plate for over-the-range microwaves. Anchors microwave to wall studs. Replace if bent, damaged, or missing to restore secure mounting.
Bought new bracket. Took the shell off and used it to put the bracket up. Read more
Replacement screw for microwaves. Secures door hinges, panels, brackets, and internal components. Use when original fastener is missing, stripped, or lost.
Attached new door after missing screw was sent to me Read more
Replacement door handle for microwave and microwave/hood combo units. Installs on the appliance door to restore a secure grip when broken, cracked, or worn.
Replaced it. Read more
Replaces a cracked, broken, or missing decorative vent grille on your microwave. Restores appearance and helps direct airflow from the grill area.
This was super easy! The dirty filters are just remove and replace items. The microwave essentially tells you when the filters should be replaced. The grease filter however, requires the removal of the Grill-Vent for access. There are two screws holding the vent in place and I had noticed when cleaning the area one day that whoever installed the vent on initial installation overtightened the screws and cracked the vent mounting holes. As a result the vent was a little shaky. I decided, since I... Read more
Protective inlet cover for microwaves. Shields wiring and connections from debris. Replace if cracked, broken, or missing to restore safe coverage.
Replacement lamp cover lens for microwave ovens. Protects and diffuses interior light. Replace if cracked, discolored, or missing to restore lighting.
This is an electronic filter board that suppresses electrical noise generated by the microwave, preventing interference with other household electronics. It is typically mounted near the power cord connection inside the microwave's cabinet. Replace this part if the microwave causes static on nearby radios or TVs, trips breakers, or fails to power on at all.
Fix a microwave that runs but won't heat with this capacitor. Works with magnetron and diode to restore heating function. Moderate DIY repair.
Replaced both of the top door switches in control panel AP4429884 and AP5950105 Made by: Whirlpool need torx drive to remove switch from cabinet. Read more
Microwave overheating or won't start? This fixed-temperature thermostat acts as a safety switch to prevent thermal damage. Straightforward repair.
Molded wire clip that secures wiring and harnesses to the microwave cabinet. Replace if broken, cracked, or missing to prevent wire rubbing and chafing.
Microwave not heating but all other functions work? This magnetron thermostat protects against overheating. Easy DIY repair in under an hour.
Removed unit from wall and took outer shell off, de-energized capacitor and then took a multi-meter and tested all the High voltage parts and magnetron. They tested out fine other than the diode and then I looked at the "Safety" circuit if you will the power loop that goes through door switches and thermostats to energize the High Voltage transformer and magnetron. Turns out the thermostat that is on the side of the magnetron wasn't closed, so I took a butane torch and heated it up past the... Read more
This thermistor measures temperature changes inside your microwave to control cooking functions and safety systems. It sends temperature readings to the control board to adjust power levels and cooking times. Replace this part if your microwave doesn't heat properly, overheats, or sensor cooking features don't work correctly.
Replacement mounting screw secures exterior panels, trim, or internal components. Needed when original fastener is missing, stripped, or damaged.
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.