Wsm2700dawww Space Maker Washer Parts
Genuine Ge part
By: Ge
Part Number: WE12X10009
Dryer drum belt wraps around drum and motor pulley to spin the drum. Replace if dryer won't start, makes squealing noise, or drum doesn't turn. Verify fit.
This part fixes the following symptoms
-
Will not tumble
-
Won't start
See more...
Do-It-Yourself Stories from Customers like You
Noisy(thump thump sweaks) when dryer was in operation Michale R. • Sinclair , WY • January 08, 2015
Replaced rear bearing, upper and lower felts, drive belt. Have repaired dryer before for same problem years ago, knew what to do, on line diagrams helped to move memory. Cleaned all accumulated lint out of machine.Belt was changed only out of age.Looked good but thought to be on safe side.
Read more
More
Genuine Ge part
By: Ge
Part Number: WE01X10160
Replacement timer knob for washer dryer combo units. Installs on the control panel to select cycle times. Order a new knob if yours is cracked or broken.
Do-It-Yourself Stories from Customers like You
Broken knob Jose P. • Chicago , IL • September 12, 2014
Replaced it with the new one. Easy as pie!!!
Read more
More
By: Pro
Part Number: TJ725RBFFP
Replacement water fill hoses for washing machines. Connect home water supply to washer. Replace when cracked, leaking, or showing rubber wear or corrosion.
Do-It-Yourself Stories from Customers like You
Washer would not spin nor adgitate Jeff A. • Stow , OH • June 28, 2015
Motor control board was flashing 4 times, indicating that the mode shifter had an error. I disconnected the mode shifter's wire from the controller and measured the resistance between the 2 leads with an ohmmeter. Since the reading was infinite, that meant that the mode shifter coil or in-line thermal sensor was electrically open, i.e. bad. As this fix is near a complete tear-down of the washing machine, here are a few tips I discovered. 1) the hub nut is difficult to remove and you need a...
Read more
More
Genuine Ge part
By: Ge
Part Number: WE4X757
Dryer won't heat or overheats? A faulty safety thermostat fails to regulate temperature. Test for continuity with a multimeter; moderate DIY repair.
Do-It-Yourself Stories from Customers like You
Faulty thermal fuse Phillip D. • Hagerstown , MD • August 23, 2015
Removed lid. Removed switch panel. Suspected open circuit in thermal fuse. Tested it with a multimeter first to confirm it had an open circuit. This part is obsolete. Contacted manufacturer and found part supercedes to a different part number Ordered part. (This website is very efficient. The part arrived with the 1.7 day promise time.) new fuse bracket is slightly larger due to supercession. Marked bolt hole locations and drilled new. Installed fuse. Re-assembled dryer in reverse order....
Read more
More
Genuine Ge part
By: Ge
Part Number: WH07X10009
Drive belt connects the motor to the drum for wash and spin cycles. Replace if stretched, frayed, cracked, or causing squealing noise. Verify fit.
Do-It-Yourself Stories from Customers like You
Worn / stretched belt William C. • Lexington , NC • March 16, 2014
The hardest part of this repair was determining where (controls, motor, belt or transmission) the problem was. I could see little pieces of rubber from the belt beneath the motor pulley, but the machine is 20 years old and some wear is to be expected. Since the belt was still intact and neither frayed or cracked and since I didn't know what the original dimensions were and since the machine was still able to agitate, I could only identify the belt as a possible source of the failure to...
Read more
More
Genuine Ge part
By: Ge
Part Number: WE03X10007
Drum glide supports the front of your dryer drum for smooth rotation. Replace when you hear scraping or squeaking sounds. Confirm fit with your model.
Do-It-Yourself Stories from Customers like You
Noisy electric dryer Richard N. • Coventry , RI • July 05, 2015
Replaced all wear parts (belt, idler pulley, drum support, glides).
Read more
More
Genuine Ge part
By: Ge
Part Number: WE11X99
Dryer not heating or leaving clothes damp? This heating element generates electric heat for proper drying. Takes under 1 hour with drum removal required.
Do-It-Yourself Stories from Customers like You
Dryer had stopped heating Matt D. • Salisbury , MD • May 08, 2015
Replaced the heater unit because the heater coil had burned in two. The whole project took less that one hour. I also replaced the dryer timer since one of the cycles would not cool down as part of the process.
Read more
More
Genuine Ge part
By: Ge
Part Number: WE16X28
This dryer blower wheel mounts on the motor shaft to move air through the drum, lint filter, and exhaust duct, helping maintain proper airflow, even drying, and overall dryer performance.
- Moves air through the drum, lint screen, and duct to exhaust moisture and lint
- If the hub is stripped or the wheel is loose on the motor shaft, airflow drops and dry times increase
- Cracked, warped, or broken fins can cause rattling, scraping, or vibration during operation
- Common symptoms include weak air at the vent, longer cycles, or unusual noise from the lower/front cabinet area
What's included: 1 blower wheel Install notes:
- Disconnect power; if gas, also shut off the gas supply. Wear gloves—sheet-metal edges can be sharp
- Access the blower housing by removing the front/lower panel and blower cover as your model requires
- Note thread direction and any retaining nut/clip when removing; transfer any reusable hardware to the new wheel
- Clear lint and debris from the blower housing and ducts; ensure the new wheel spins freely without rubbing before reassembly
Do-It-Yourself Stories from Customers like You
Blower fan Roger K. • Canton , NC • August 03, 2019
Replaced it
Read more
More
Genuine Ge part
By: Ge
Part Number: WH12X10164
Washer fills but won't agitate or advance cycles? The timer controls wash, rinse, and spin sequences. DIY repair typically takes 15-30 minutes.
Do-It-Yourself Stories from Customers like You
Idler was broken and the timer no longer functioned properly George H. • Miami , FL • September 20, 2014
I live overseas and these parts were not available locally. I have a repair person who takes care of all my appliances. He installed the new parts in about 15 minutes and my washer is working fine now.
Read more
More
Genuine Ge part
By: Ge
Part Number: WE04X10094
This thermal limiter is a safety fuse designed to protect the dryer from overheating by cutting off power to the heating element if temperatures exceed safe limits. It is typically mounted on or near the heating element housing. Replace this part if the dryer is not heating at all, as a blown thermal limiter is a common cause of no-heat conditions often triggered by restricted airflow or a clogged vent.
Do-It-Yourself Stories from Customers like You
Belt jumped off idler did not trip belt switch at first thermal limiter shut dryer down Bill M. • Bradenton , FL • January 16, 2017
REPLACED BELT AND IDLER. TESTED AND FOUND THERMAL LIMITER BLOWN SO REPLACED IT. DRYER WORKS GOOD
Read more
More
Genuine Ge part
By: Ge
Part Number: WE03X29378
Keep your dryer drum turning smoothly. This idler & pulley assembly maintains proper tension on the drive belt so the drum rotates quietly and efficiently when the original idler or pulley becomes worn, noisy, or seized. What it does:
- Applies spring-loaded tension to the drive belt for consistent drum rotation
- Provides a smooth rolling surface to minimize belt friction and wear
- Worn/failed parts may cause squealing or chirping, the drum not turning, the belt slipping off or breaking, or a hot rubber smell
What's included:
- One idler and pulley assembly
Install notes:
- Disconnect power; for gas dryers, also shut off the gas supply
- Access the belt path by removing the necessary panels per your service information
- Pull the idler to release belt tension, remove the old assembly, install the new one, and route the belt correctly around the motor and idler
- Manually rotate the drum to verify belt tracking before reassembly and test run
More
Genuine Ge part
By: Ge
Part Number: WE4X775
Fix a dryer that won't start, won't advance cycles, or has a smoking timer. This control timer restores proper cycle operation. DIY repair in 1 hour.
Do-It-Yourself Stories from Customers like You
Dryer had stopped heating Matt D. • Salisbury , MD • May 08, 2015
Replaced the heater unit because the heater coil had burned in two. The whole project took less that one hour. I also replaced the dryer timer since one of the cycles would not cool down as part of the process.
Read more
More
Genuine Ge part
By: Ge
Part Number: WE13X10011
Dryer drum shaft support with shaft assembly. Replace if drum drops, shaft breaks, or squealing occurs from worn bearings. Verify fit with your model.
More
Genuine Ge part
By: Ge
Part Number: WE13X28680
Secures the rear drum bearing to keep your dryer drum aligned and rotating smoothly. Replace if bracket is cracked, bent, or worn to restore proper support.
More
Genuine Ge part
By: Ge
Part Number: WE02X10024
Terminal block mounting screw for dryers and washer dryer combos. Secures the terminal block to the dryer frame. Replace if stripped, missing, or damaged.
More
Genuine Ge part
By: Ge
Part Number: WE1X1262
This is an electrical plug connector used in the dryer's wiring system. It provides a secure connection point for internal wiring to ensure proper electrical flow to dryer components. Replace this plug if it is burned, melted, cracked, or if you are experiencing intermittent power issues with the dryer.
More