We use cookies and similar tools for site analytics and advertising. By using our site, you agree to this. See our Privacy Policy for details. Do Not Sell or Share My Personal Information
Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Dryer drum belt wraps around drum and motor pulley to spin the drum. Replace if dryer won't start, makes squealing noise, or drum doesn't turn. Verify fit.
Replaced rear bearing, upper and lower felts, drive belt. Have repaired dryer before for same problem years ago, knew what to do, on line diagrams helped to move memory. Cleaned all accumulated lint out of machine.Belt was changed only out of age.Looked good but thought to be on safe side. Read more
Replacement water fill hoses for washing machines. Connect home water supply to washer. Replace when cracked, leaking, or showing rubber wear or corrosion.
Motor control board was flashing 4 times, indicating that the mode shifter had an error. I disconnected the mode shifter's wire from the controller and measured the resistance between the 2 leads with an ohmmeter. Since the reading was infinite, that meant that the mode shifter coil or in-line thermal sensor was electrically open, i.e. bad. As this fix is near a complete tear-down of the washing machine, here are a few tips I discovered. 1) the hub nut is difficult to remove and you need a... Read more
Dryer won't heat or overheats? A faulty safety thermostat fails to regulate temperature. Test for continuity with a multimeter; moderate DIY repair.
Removed lid. Removed switch panel. Suspected open circuit in thermal fuse. Tested it with a multimeter first to confirm it had an open circuit. This part is obsolete. Contacted manufacturer and found part supercedes to a different part number Ordered part. (This website is very efficient. The part arrived with the 1.7 day promise time.) new fuse bracket is slightly larger due to supercession. Marked bolt hole locations and drilled new. Installed fuse. Re-assembled dryer in reverse order.... Read more
Drive belt connects the motor to the drum for wash and spin cycles. Replace if stretched, frayed, cracked, or causing squealing noise. Verify fit.
The hardest part of this repair was determining where (controls, motor, belt or transmission) the problem was. I could see little pieces of rubber from the belt beneath the motor pulley, but the machine is 20 years old and some wear is to be expected. Since the belt was still intact and neither frayed or cracked and since I didn't know what the original dimensions were and since the machine was still able to agitate, I could only identify the belt as a possible source of the failure to... Read more
Dryer not heating or leaving clothes damp? This heating element generates electric heat for proper drying. Takes under 1 hour with drum removal required.
Replaced the heater unit because the heater coil had burned in two. The whole project took less that one hour. I also replaced the dryer timer since one of the cycles would not cool down as part of the process. Read more
Secures washer hoses at pump, tub, and valve connections to prevent leaks and hose blow-offs. Replace worn or missing clamps for a tight seal. Confirm fit.
The video was very helpful. the hardest part is getting off old rusted parts. I had to use a hacksaw to remove one of the old clamps. I had to open the bottom of the washing machine to remove of the other clamp. Putting the new parts on was easy. Getting everything apart was a challenge. Putting the new parts on was an easy 5 minute job. Read more
This dryer blower wheel mounts on the motor shaft to move air through the drum, lint filter, and exhaust duct, helping maintain proper airflow, even drying, and overall dryer performance.
Replaced it Read more
Keep your dryer drum turning smoothly. This idler & pulley assembly maintains proper tension on the drive belt so the drum rotates quietly and efficiently when the original idler or pulley becomes worn, noisy, or seized. What it does:
Fix a dryer that won't start, won't advance cycles, or has a smoking timer. This control timer restores proper cycle operation. DIY repair in 1 hour.
Dryer drum shaft support with shaft assembly. Replace if drum drops, shaft breaks, or squealing occurs from worn bearings. Verify fit with your model.
Secures the rear drum bearing to keep your dryer drum aligned and rotating smoothly. Replace if bracket is cracked, bent, or worn to restore proper support.
This is an electrical plug connector used in the dryer's wiring system. It provides a secure connection point for internal wiring to ensure proper electrical flow to dryer components. Replace this plug if it is burned, melted, cracked, or if you are experiencing intermittent power issues with the dryer.
Secures the front panel on dryers. Replace if the panel is loose, rattling, or won't stay in place. Confirm fit with your model number before ordering.
Replaced all wear parts (belt, idler pulley, drum support, glides). Read more
A replacement pan head screw used to fasten appliance panels and components. Its standard #8 coarse thread and 3/8-inch length secure trim, brackets, and small assemblies for stable operation. What it does:
Protective cap stud cover for washer dryer combo units. Shields electrical or mechanical studs from debris and maintains secure connections. Replace if cracked, broken, or missing.