Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Refrigerator door cam pivot that guides the door during opening and closing. Replace if cracked, worn, or causing clicking sounds or difficulty closing.
Replaced both sets of door cams on my Kenmore Elite Refrigerator. The most important thing to know is that you DO NOT have to remove the doors from the refrigerator to replace BOTH sets of cams. You just have to remove the lower grill which is a snap fit (I also turned off the water and unplugged the unit). My fridge has an ice and water dispenser where the water and electrical lines go through the cams on the left side. Be sure to order the correct parts as the cam holes on the freezer side... Read more
Clear plastic door bin snaps into refrigerator inner door liner to hold bottles, jars, and condiments. Replace cracked, broken, or missing bins.
Installed in less than 5 minutes! Read more
This factory screw secures appliance components to their mounting points. Replace missing, worn, or stripped hardware to restore a tight fit, proper alignment, and quieter operation across the affected assembly.
Ordered Bake Element, Y04100019 (Whirlpool AP4283614) to replace a broken bake element on my 30-year old Jenn-Air Model S125 Downdraft Slide-in electric range. Received the element very quickly but it had been damaged in shipping. Called AppliancePartsPros to report this and they quickly shipped another element - very easy process. To install the element, I turned off the power to the range, put on rubber gloves (just in case) and removed the two sheet metal crews at the rear of the oven -... Read more
Water tube that routes supply from inlet valve to filter housing. Replace if cracked, kinked, or leaking to restore proper water flow to dispenser.
Drive pulley mounts to the washer basket shaft and routes the belt from the motor. Replace if worn, cracked, loose, or showing play on the shaft.
Replaced the shaft & mode shifter assembly. Also replaced the pulley as it had taken some damage from the wobbling clutch dog. And replaced the tub seal since it's normally inaccessible with the shaft in place. This is an advanced repair that took a lot of time. Removing the tub nut took a 1 11/16" socket and a 700 ft-lb impact wrench and I had to hammer on the nut for several minutes to break it free of the tub. Disassembly of the washer is complete, and requires a lot of space for... Read more
Secures the bottom grille to your refrigerator frame. Replace if the original clip is cracked, broken, or missing and the grille won't stay in place.
Easy fixes, but I did what one of your video clips Read more
Holds tub dampening straps in place on your washer. Replace if cracked, broken, or worn from heavy loads. Includes installation video guide.
I have a 14 year old GE washing machine that had been making a lot of noise while running but had eventually just stopped flat. The agitator and spin cycle would not run. I found this site and made excellent use of all the repair videos to study about my issue. I put in my machine model number and I Immediately was able to start honing in on what my problem could be from website advice about popular repair parts, stories others had shared about their similar machine issues and watching videos,... Read more
Replace a cracked, broken, or missing dairy tray on your refrigerator door. This bin installs on the door to organize butter and small items in one spot.
Had the cover but needed the tray….put cover on new tray... Read more
Ice dispenser not working? This refrigerator ice lever activates ice release when pressed. Common fix for broken or worn levers. DIY-friendly repair.
The water dispenser stopped working on my Sears Kenmore (Whirlpool) side-by-side refrigerator and after much research on the web I purchased the parts that commonly failed for this condition. I should have first taken the dispenser assembly apart but I didn't--it looked a little too intimidating to do twice. As it turns out, what actually broke was the plastic assembly that holds the water actuator switch in place so the dispenser lever could not strike it. I was able to secure it in place... Read more
Seals the flood/overflow hose connection to your washer tub. Replace if water seeps from the tub area or the gasket feels soft. Confirm fit by model.
Pulled front panel off. Unbolted and removed top cover. Removed tub trim cover. Removed and replaced gasket and dampers. Put it a back together took about 20 minutes Read more
Covers the ice bin opening in your freezer compartment. Replace this door if it's cracked, warped, or broken to restore a proper seal and easy access.
Replaced Case Water Filter assembly DA81-05883A. Please read my post entirely before starting. I completed all the tasks that I could without having to disconnect the refrigerator since it was full of food. First I removed the panel on top of the refrigerator that covers the water line that feeds the dispenser. Do not disconnect any electrical connections or the water line at this time. Remove the panel from the back bottom of the refrigerator that covers the compressor and water valve,... Read more
Interior light bulb for upright freezers. Replace when burned out or flickering to restore visibility. Verify compatibility with your model number.
Replacement support stud that holds refrigerator shelves securely in place. Needed when original peg is broken, cracked, or missing from shelf wall.
Myself Read more
Replaces the upper butt hinge assembly that mounts to the cabinet and supports your freezer or refrigerator door. Needed when hinge is cracked or worn.
Looked up parts on internet using diagrams, ordered parts, they arrived in 2 days and installed them. Read more
Front handle trim for your refrigerator's deli or meat drawer. Replace if cracked, broken, or missing to restore a secure grip and clean appearance.
Replaced rather than purchasing a new refrigerator. Installation was very easy. I was a truly impressed as to how quickly my purchase arrived. It all arrived within 3 days of purchase. Thanks Will keep checking back for shelves that were out of stock when I made my purchase. My refrigerator looks almost new again. Read more
This replacement screw secures appliance panels and components so they stay tight and aligned during use. Replacing a missing or damaged screw restores a solid fit and helps eliminate rattles, loose trim, or shifting parts.
After being told by a service repairman that it would cost me close to $200 to repair, I resolved to just not use the dispenser. After about a year, I had decided that I wanted to repair it and would look at the options myself. At the least, I could figure out which parts were needed to repair it and have them on hand for a service guy if I determined I could not do the job myself. The more I studied it, the more I felt confident that I could do it, and sure enough, when the part arrived - a... Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.