Wt1011cw Parts

This thermistor assembly monitors water temperature inside the washer tub and relays a precise signal to the control board. Replacing a failed sensor restores accurate temperature sensing and helps prevent cycle errors and performance issues. What it does:

• Measures wash water temperature and sends the signal to the electronic control
• Enables the control to adjust cycle operation based on temperature feedback
• Common failure signs: tE/TE error codes on some models, incorrect temperatures, long cycles, or cycles that won't advance
• Intermittent faults may cause sporadic errors or inconsistent performance

• 1 thermistor assembly

• Disconnect power and shut off water before servicing
• Access location varies by model; the sensor is typically mounted in the outer tub or heater housing
• Unplug the harness, pull the old sensor straight out; seat the new sensor fully and reconnect the harness
• Route wiring away from moving parts; restore power and run a test cycle, checking for proper operation and any leaks around the sensor port

Replacement nut that secures drawer and trim components on compatible LG appliances. It restores a firm, vibration-resistant fastening to help prevent loosening, rattling, or misalignment during normal use. What it does:

• Secures drawer, trim or small mounting brackets to the appliance chassis.
• Helps stop loosened fasteners that cause rattling or misaligned panels.
• Provides proper thread engagement for a stable connection.
• Matches the appliance's original fastening point when used as the listed part.

• Always disconnect power to the appliance before beginning any repair.
• Use the correct-size wrench or socket; avoid overtightening to prevent stripped threads.
• Inspect mating screw/bolt and threads for damage; replace damaged hardware as needed.

This filter assembly is the appliance's line noise filter. It conditions incoming AC power and suppresses electrical interference to protect sensitive controls and help restore stable, reliable power when the original filter has failed. What it does:

• Suppresses EMI/RFI on the AC line to reduce electrical noise reaching the control system
• Helps stabilize power to boards, relays, and motors
• Common failure symptoms: no power, intermittent power, tripped breaker or blown line fuse, burning smell or visible scorching at the old filter
• Also known as a line filter, EMI filter, or noise filter

• 1 filter assembly

• Disconnect power to the appliance before servicing; capacitors in some products can retain a charge
• Note wire locations; transfer leads to identical terminals on the new filter and secure the ground connection
• Mount the assembly firmly in the original location to prevent vibration or wire strain
• After replacement, inspect related fuses and wiring if the old filter showed signs of overheating or surge damage

This is a small OEM washer used with the washer's internal mounting hardware to provide proper spacing and secure fasteners. It helps keep assemblies aligned and prevents hardware from loosening during operation. What it does:

• Acts as a spacer and load distributor for bolts or screws in the washer assembly
• Helps maintain proper alignment of panels or components
• Reduces wear between mating metal parts
• Can prevent fasteners from backing out due to vibration

• One washer as pictured

• Always unplug the appliance and shut off the water supply before servicing
• Access the mounting location per the service manual or parts diagram; replace only like-for-like
• Install with the correct orientation and hardware; do not overtighten fasteners
• If other fasteners or parts are corroded or worn, replace them at the same time

A small fastening nut that secures drawer-related hardware and helps keep moving parts aligned and stable. Replacing a worn or missing nut restores secure attachment and reduces play or noise in the drawer assembly. What it does:

• Holds drawer hardware or related components in place to prevent shifting during use
• Helps maintain proper alignment of sliding or moving parts
• Can eliminate looseness, rattling, or intermittent catching caused by a missing or damaged nut
• Provides a secure threaded connection when used with the matching bolt or stud

• Disconnect power and remove the drawer or access panel before servicing to avoid injury
• Use the correct size wrench or socket; hand-start threads to avoid cross-threading
• Tighten snugly but avoid overtightening to prevent stripping the threads or damaging components
• If the original nut failed due to wear or corrosion, inspect the mating bolt/stud and replace if damaged

This replacement holder is a small mounting bracket used to secure components inside the appliance, restoring proper alignment and support so parts sit firmly and operate as intended. Ideal when a cracked or worn holder causes instability. What it does

• Secures internal components or assemblies to prevent movement or vibration
• Restores proper alignment when a damaged holder allows parts to sag or shift
• Helps reduce noise from loose or unsecured components
• Commonly replaced when the original holder is cracked, broken, or missing

• Turn off and unplug the appliance before beginning any repair.
• Inspect surrounding clips and fasteners; replace any damaged hardware for a secure fit.
• Use appropriate hand tools; avoid forcing parts to prevent further breakage.

This sensor switch assembly restores the appliance's ability to detect position or operational signals so cycles start and controls respond correctly. Replaces a failed or intermittent sensing switch to address start, control, or sensor-related errors. What it does:

• Sends position/sensor signals to the control board so the appliance knows when a door, lid or component is closed or in the correct position
• Prevents operation when the appliance detects an unsafe or open condition (safety interlock behavior)
• Helps stop intermittent operation, no-start conditions, or control board error codes tied to a failed sensor switch
• Often used when a switch is unresponsive, physically broken, or has loose connector issues

• Always disconnect power before servicing the appliance to avoid shock or injury
• Match the connector orientation and secure any retaining clips or screws; do not force connectors
• Access may require removing an outer panel, door trim, or control housing
• After installation, restore power and verify door/sensor function and normal cycle operation; if you see persistent errors

This tapping screw fastens appliance panels and components for a secure, lasting hold. Replace stripped, rusted, or missing hardware to restore proper fit, reduce vibration and rattling, and keep brackets, covers, and trim tightly in place.

• Fastens metal or plastic panels, trim, or brackets to the appliance cabinet/frame
• Cuts its own threads in pre-drilled holes for a tight, reliable fit
• Helps maintain alignment and reduce movement that can cause noise
• Replace when the original screw is missing, stripped, corroded, or will not tighten

• Disconnect power and shut off water/gas before servicing
• Match the screw's position and length to the original hardware
• Start by hand to avoid cross-threading; tighten snugly—do not overtighten
• Reuse any washers or spacers from the original assembly if present

This adjustable leg assembly raises and levels the appliance to keep it stable and reduce rocking. It provides a simple way to set appliance height for proper door alignment and smooth operation. What it does:

• Supports the appliance and transfers weight to the floor
• Allows height adjustment to level uneven floors
• Helps prevent excessive vibration, rocking, and noise
• Promotes proper door/drawer alignment and seal

• One leg assembly

• Disconnect power and empty the appliance before adjusting or replacing legs
• Raise or support the appliance safely before removing or installing the leg
• Adjust by turning the leg; tighten securely but avoid over-torquing

This spring-style hose clamp secures flexible hoses to fittings to help maintain a watertight connection and prevent leaks. A simple replacement when the original clamp is worn, bent, or no longer holds tension. What it does:

• Holds washer, drain, or water-supply hoses firmly on barbs and fittings
• Restores clamping tension to stop drips or slow leaks at hose connections
• Prevents hoses from slipping off under pressure or vibration
• Helps maintain proper fluid flow by ensuring a tight seal

• One hose clamp

• Disconnect power and shut off water supply before servicing plumbing connections
• Use pliers or the appropriate clamp tool to expand and position the clamp; release slowly to seat it
• Replace any damaged or corroded hoses or fittings for a reliable repair

This screw cap covers and protects an exposed screw head or mounting hole, restoring a clean, finished appearance and helping shield the area from dirt and moisture. Use it to replace a missing, cracked, or discolored cap.

• Conceals and protects a visible screw head or mounting hole
• Helps keep dust and moisture out of the opening
• Restores a clean, factory look when the original cap is lost or damaged
• Common symptoms: cap missing, cracked, loose, or won't stay in place

• Disconnect power and shut off water when working near electrical or moving parts
• Align the cap over the screw head or hole and press evenly until fully seated—do not force
• If removing an old cap, use a plastic pry tool to avoid scratching nearby surfaces
• Ensure the underlying screw or fastener is properly tightened before installing the new cap

This rubber door boot gasket creates a watertight seal between the washer door and drum to help prevent leaks and keep laundry contained during cycles. It restores a proper seal for front-load washers. What it does

• Replaces a worn or torn door boot to stop or reduce water leaking from the door area
• Restores the flexible seal that cushions the door-to-drum interface during operation
• Helps prevent mold buildup by eliminating gaps where water can collect
• Suitable when visual damage, cracking, or persistent leaks are present around the door seal

• One replacement door boot gasket

• Only install on compatible front-load washer models; refer to your model's parts list for fit
• Disconnect power and water supply before starting any repair
• Inspect and clean the door rim and tub flange before fitting the new gasket to ensure a proper seal
• Use proper clamps or retaining ring as required by your model; replace any damaged hardware

This inlet hose directs household water into the washer so the machine can fill for wash cycles. It replaces a worn or damaged inlet connection to restore proper water flow and stop leaks. What it does

• Carries incoming water from the home supply to the washer's fill system.
• Stops leaks or drips caused by cracked or damaged inlet tubing.
• Helps restore normal filling when a damaged inlet restricts water flow.
• Works with factory inlet fittings and connections for a direct replacement.

• Turn off the washer and shut off the home's water supply before beginning work.
• Check and replace any rubber washers or O-rings at the connections if they are worn.
• Hand-start fittings, then tighten securely with a wrench — avoid over-tightening.
• After installation, run a short fill cycle and inspect all connections for leaks.

This is a replacement door hinge that supports and pivots the refrigerator/freezer door for smooth opening and proper alignment. Restores secure door movement and helps maintain an even seal for reliable cooling. What it does

• Provides the pivot point that lets the door open and close smoothly
• Keeps the door properly aligned to prevent rubbing, sagging, or gaps
• Helps the door form a consistent seal to maintain internal temperature
• Commonly replaced when the door drops, squeaks, or binds during use

• Disconnect power and remove food from affected door area before starting work
• Support the door while removing and installing the hinge to prevent dropping or damage
• Use proper tools and follow manufacturer torque recommendations for fasteners