Wtw8127lc Parts

The Hose Clamp is an OEM part for Whirlpool washing machines. This clamp secures the hose in place, ensuring a tight connection and preventing leaks during operation. It is essential for maintaining the integrity of the washing machine's water system, securing hoses that carry water to and from the washer.

Common causes of a bad hose clamp include rust, physical damage, or loosening from repeated tightening and loosening.

Symptoms of a bad hose clamp include:

• Water leaks around the hose connection points
• The hose slipping off the fitting
• Visible rust or wear on the clamp
• Difficulty in tightening the clamp to secure the hose

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore models.

Replacement screw for securing washer panels, brackets, and internal assemblies. Replaces missing, stripped, or corroded hardware to restore fit.

Connects washer tub to drain pump. Replace if cracked, split, or chewed by rodents. Common wear from chemicals and rubbing against machine components.

The Spring Tension Hose Clamp is an OEM part for Whirlpool washing machines. It is designed to secure hoses in place, preventing leaks by maintaining consistent tension on the hose connections.

Over time, spring tension hose clamps can lose their effectiveness due to metal fatigue, corrosion, or damage from frequent tightening and loosening. This can lead to leaks and improper hose connections.

Symptoms of a bad spring tension hose clamp include:

• Water leaks around hose connections
• Loose or disconnected hoses
• Unusual noises or vibrations during operation
• Water pressure issues within the washing machine

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Washer overfilling or not filling properly? A damaged pressure switch hose prevents accurate water level sensing. Easy 15-minute DIY fix with video.

If clothes aren't moving during wash cycles or agitator spins freely, this vertical post replacement restores proper wash action in top-load washers.

Secures the rear bearing housing to the tub assembly in your washer. Replace if loose, worn, or during bearing repairs. Verify fit with your model number.

The Console Clip is an OEM part compatible with Whirlpool dryers. This clip secures the control console assembly to the top panel, ensuring it is firmly mounted during operation. Properly functioning clips are necessary to maintain the correct alignment of controls and prevent detachment. 

Causes of a bad clip can include wear and fatigue from repeated opening and closing of the dryer door. Excessive force or impact could also bend or break the clip over time.

Symptoms of a bad clip include:

• Loose console assembly that is not securely fastened  
• Misaligned or dangling controls that do not sit flush
• Dislodged console at risk of detaching from housing
• Missing clip leaving an open mounting point

This OEM Whirlpool replacement clip is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

If your washer won't fill with water or fills too slowly, this water inlet valve assembly controls water flow into the tub. Direct replacement part.

This 8-18 x 5/8-inch screw secures dryer panels, brackets, and covers. Replace missing or stripped fasteners to restore a tight fit and stability.

This replacement screw secures panels, brackets, and other components in your appliance to keep them aligned and rattle-free. Replacing worn, stripped, or missing hardware restores a tight fit and helps maintain safe, quiet operation.

• Fastens panels, brackets, or internal parts to the cabinet/frame
• Helps maintain alignment to reduce vibration and rattling
• Replaces lost, stripped, or corroded screws
• Common symptoms: loose panels/trim, rattles, or a screw that won't tighten

• Disconnect power; shut off water or gas if applicable
• Match thread and length to the original; replace one at a time to keep alignment
• Start threads by hand to avoid cross-threading; use the correct driver
• Tighten snugly—do not overtighten, especially into plastic or thin sheet metal

If your washer won't spin or makes loud chirping noises, the rotor may be damaged. Visual inspection checks for magnet damage. Requires T20 torx driver.

Adjustable leveling leg threads into the washer base to support and stabilize the unit. Replace if cracked, stripped, or missing to level cabinet.

The Dispenser Switch is an OEM component for Whirlpool washing machines. Located inside the detergent compartment, it detects when the door is properly closed to enable cycle functions.   

The sensitive switch utilizes durable contacts to reliably connect without false readings due to vibration. Its secure plastic housing contains electronic components regulating additive distribution during selected cycles.

Symptoms of a bad dispenser switch can include:

• Inability to start cycles despite closed door
• Dispenser door fails to lock properly   
• Fault codes relating to dispenser issues  
• Cycles unexpectedly terminating mid-load

Replace yours today with this genuine Whirlpool switch to ensure detergent and other additives activate at optimal times for thorough, even cleaning. Compatible with Kenmore, Maytag, and some Jenn-Air washers.

This WASHER  is an OEM part specifically designed for Whirlpool top-load washing machines. Tailored to fit seamlessly, this component ensures the efficient operation of the washer. It plays a crucial role in maintaining the stability and balance of the machine during the washing cycles.

A damaged or worn-out top-load washer can negatively impact the appliance's performance. Causes of a defective washer might include prolonged use, physical damage, or exposure to excessive weight or force, resulting in instability or imbalance during operation.

Symptoms of a bad WASHER may include:

• Excessive vibration or shaking during the wash cycle
• Difficulty in maintaining balance while spinning
• Noisy or erratic behavior during the operation

This is a genuine Whirlpool OEM replacement this part is also compatible with Maytag, Jenn-Air, and some Kenmore models.

Fix a cracked or discolored lid lock bezel on your washer. This bezel snaps around the lid lock assembly. Easy install—remove lid lock, pinch tabs, lift out.