Wtw8540bc0bw0 Parts

This hose clamp secures a flexible hose to its fitting to help prevent leaks and hose blow-offs during operation. Replace a rusted, stripped, or distorted clamp to restore a tight, reliable seal at the connection point.

• Applies clamping force around a hose to hold it on a barb or stub fitting
• Commonly used on washer drain and tub-to-pump hose connections
• Helps stop drips at the joint and prevents the hose from slipping off
• Typical failure signs: leaking at the connection, clamp won't tighten, visible rust, broken/warped band

• Unplug the appliance and turn off water supply; expect some residual water
• Seat the hose fully on the fitting; place the clamp just behind the bead/barb
• Tighten until snug and secure; do not overtighten to avoid damaging the hose
• Run a short test cycle and recheck for leaks at the connection

This hose clamp secures dishwasher hoses to fittings and ports to maintain a tight, leak-resistant seal. Replacing a worn clamp helps prevent drips and loose connections that can cause water under the unit.

• Secures drain or circulation hose to the pump, sump, or other dishwasher fittings
• Helps maintain a watertight seal at hose connection points
• Can help resolve water dripping from a hose joint or a loose hose
• Replace if corroded, deformed, cracked, or no longer holds tension

• Disconnect power and turn off the water supply before servicing
• Place a towel or shallow pan to catch residual water when removing hoses
• Fully seat the hose on the fitting, position the clamp over the barb/connection, and secure firmly
• After reassembly, run a brief fill/drain and check all connections for leaks

This recirculation pump assembly drives water through the appliance's circulation system, maintaining steady flow and pressure for proper operation. Replace it if water won't circulate, performance drops, or the unit becomes noisy or shows a pump-related error.

• Moves water through internal channels to maintain consistent circulation and pressure
• Helps ensure effective cleaning/operation during wash or circulation steps
• Common failure symptoms: no/weak water movement, poor results, humming or grinding noises
• Trigger pump/circulation error messages or cause cycles to stall

• Disconnect power and shut off water supply before servicing
• Access is typically from the bottom/front; remove toe-kick or lower panels as needed
• Expect residual water; protect the area and transfer clamps/fittings from the old pump if required
• Seat any seals properly, reconnect hoses/wiring securely, and test for leaks and proper circulation

This is a replacement screw designed to work with a wide range of household appliances. It is used for many purposes in these appliances, from holding body panels together to securing electronics into control boards. However, screws are subject to damage through corrosion, impact, and improper installation/removal. In most cases, the primary damage to this screw is through corrosion – it may become rusted or corroded in place, depending on the appliance and the maintenance provided during its lifespan. The screw may also be stripped or rounded due to improper removal or installation. If the screw is damaged, lost, or corroded in place, it will need to be replaced. In most cases, removal will require nothing more than a Phillips head screwdriver or the appropriately sized socket with a ratchet. However, if the screw is damaged, it may require a tap set to remove it from its mounting location. Note that this is a genuine OEM replacement screw made from durable, high-quality metal, and is sold individually. It fits Whirlpool, Maytag, Roper, Estate, Amana, Crosley, and Thermador appliances. It is used in over 150 machines, ranging from washers and dryers to air conditioners.

This replacement detergent dispenser assembly mounts in the dishwasher door and releases detergent at the correct time in the cycle to help ensure thorough cleaning and consistent wash results. What it does:

• Holds and seals detergent until the control signals it to open
• Releases detergent into the tub for proper wash performance
• Common failure symptoms: detergent left in cup, dispenser door won't latch or open, leaks around the dispenser area, or poor cleaning due to no detergent release

• One detergent dispenser assembly

• Disconnect power and turn off water supply before servicing
• Remove the inner door panel to access the dispenser retainers
• Release the old dispenser, transfer any electrical connector(s), and seat the new dispenser evenly to ensure a watertight seal
• Reassemble, run a short cycle, and check for leaks around the dispenser

Contains two, six foot long braided hoses with 90 degree ends.

This low-profile washplate mounts at the bottom of the tub to circulate water and roll laundry during the wash cycle. Replacing a stripped, loose, or cracked plate restores proper wash action and cleaning performance. What it does:

• Mounts to the drive shaft splines to create wash action and move water.
• Turns and lifts laundry for proper turnover and cleaning efficiency.
• Can address grinding/clicking during wash or wobble caused by broken fins.

• Includes: 1 washplate

• Disconnect power and water before servicing.
• Remove the center cap/cover to access the hold-down bolt; remove the bolt and lift off the old washplate. A puller may be needed if the plate is seized.
• Align the new plate with the shaft splines, press it fully down, reinstall the bolt and cap, and run a test cycle.

This set of washer fill hoses connects your home's hot and cold water supply to the washer's inlet valves. Replacing aging hoses helps prevent leaks and ensures the washer fills properly for every cycle.

• Supplies hot and cold water from household faucets to the washer's inlet valves
• Helps address leaks, bulges, or cracks in old hoses
• Can resolve drips at fittings and water on the floor
• Improve slow or no-fill issues caused by kinks or internal blockages

• Unplug the washer and turn off both water supplies before starting
• Place a towel or pan to catch residual water; disconnect old hoses from faucets and inlet valves
• Attach new hoses to the correct hot/cold connections; tighten connections securely without overtightening
• Open valves, check for leaks at both ends, and re-tighten if needed

Color: White

This nozzle assembly directs fresh water for the refrigerator's fresh-fill function, restoring controlled filling and helping prevent leaks and drips. Replace a damaged nozzle to restore reliable water dispensing. What it does:

• Directs and meters fresh water flow during the refrigerator's fill cycle.
• Helps prevent water from spraying or dripping away from the intended fill area.
• Common symptoms for replacement: visible leaks, dripping after fills, inconsistent or no water during fill cycles.
• Interfaces with the fridge water tubing and fill valve to deliver proper flow.

• Disconnect power to the appliance before starting any repair.
• Shut off the water supply and drain residual water to avoid spills.
• Replace using basic hand tools; ensure proper seating and secure connections to avoid leaks.

Size: 29 1/4 inches x 31 1/4 inches. This universal washer drip tray is large enough for duet washers and sits under the washer to protect your floors from scuffs, spill, etc. Includes a PVC drain fitting.

Used from harness to top.

Replacement fabric softener dispenser assembly for top-load washers. Restores proper softener release during the rinse cycle so your clothes get even conditioning while preventing pooling, clogs, and leaks from a damaged dispenser. What it does:

• Delivers fabric softener into the rinse cycle for even distribution and improved fabric feel.
• Replaces a broken, cracked, or clogged dispenser that won't release softener.
• Stops softener from pooling in the drawer or leaking into the washer tub.
• Re-establishes correct dispenser operation so the washer times and releases additives properly.

• Disconnect power (unplug) and turn off water before servicing the washer.
• Remove the dispenser drawer, drain any remaining softener, then remove and replace the assembly in the correct orientation.
• Reinstall the drawer, restore power/water, and run a rinse cycle to check for leaks.

This factory washer is used in appliance assemblies to distribute load under a fastener and maintain a secure, accurate fit. Replace a missing or damaged washer to restore proper stack-up and reduce vibration, noise, or loosening.

• Distributes load and provides proper spacing in the fastener assembly
• Helps keep bolts, screws, or nuts tight to minimize vibration and rattling
• Direct replacement when the original washer is worn, bent, cracked, or missing
• Typical signs include loose panels/brackets, recurring looseness after tightening, or new vibration after service

• Unplug the appliance; shut off water supply if working near hoses or valves
• Note the original hardware stack-up and reassemble in the same order
• Inspect mating surfaces and companion hardware; replace any damaged parts
• Tighten fasteners snugly per service guidance; avoid overtightening

Size: .20 Fl. Oz. (6 ml)

This small tension spring restores the return force in the top lock mechanism so it latches securely and releases smoothly. Replacing a fatigued spring helps the lock operate consistently and keeps the panel/top properly secured.

• Provides the return/tension force for the lock lever or arm
• Helps the lock engage fully and stay secured under vibration
• Restores proper latch feel and consistent lock/unlock action
• Common signs include a loose/floppy lock, poor engagement, or the lock not returning to position

• Disconnect power and allow the appliance to cool; shut off gas supply if applicable
• Note the spring's routing/orientation before removal
• Use needle-nose pliers; mind sharp edges and pinch points
• After installation, manually check lock movement for smooth travel