Wtw8540bc0bw0 Parts

After about 6 months of use with our Whirlpool Cabrio washing machine it started to sound extremely loud in the spin cycle, we should have called Whirlpool at this point to have it looked at under warranty. Fast forward 5 years later our loud washing machine ended up leaking out the bottom, we had a local service company come out to take a look at doing the repair and they quoted $800 to replace the outer tub assembly. I was not going to pay $800 and figured that most likely we would purchase a... Read more

• Noisy

After ignoring for a couple of years that the bearings were bad on our Whirlpool Cabrio washer and just closing the door to the laundry room, it started slinging grease underneath during the spin cycle. Knowing that the cost to call out a repairman would be close to the cost of a new washer, I decided that it would be a nice Saturday project after reviewing AppliancePartsPros’ repair video. The bearing & tub seal kit and bearing installation tool arrived in two days. I’ve done a lot of... Read more

• Won't start
• Lid or door will not open
• Lid or door won't close

Video on the appliance pros site was great. Very clear and guided me through every step, I think anyone can feel confident making this lid switch repair. Read more

As a Mechanic, I did the common sense approach: INITIAL OBSERVATIONS & CHECKS: - Unplug Machine & check inlet water hose connections for leaks and signs of hose failure; - Remove back panel & inspect for water presence at all hose connections, pump, bottom of basket (bottom center of basket where the main motor, shaft bearing, and tub seal is located), dispensers, bottom of wash basket, water injector area, look everywhere where there is a hose connection and where water flows... - Inspect... Read more

Disconnected the water lines and unplugged the washer. Tilted the machine on its front side 3/4 of the way as machine still retains some water even after drain. From bottom of the machine I used an allen wrench to remove screw in center of shroud and remove plastic shroud containing the magnets along its sides thar drives the motor. Then using a 3/8 socket i removed the 4 bolts holding the retaining plate holding the magneto ring. I used a small plastic garbage can side to rest the... Read more

As a Mechanic, I did the common sense approach: INITIAL OBSERVATIONS & CHECKS: - Unplug Machine & check inlet water hose connections for leaks and signs of hose failure; - Remove back panel & inspect for water presence at all hose connections, pump, bottom of basket (bottom center of basket where the main motor, shaft bearing, and tub seal is located), dispensers, bottom of wash basket, water injector area, look everywhere where there is a hose connection and where water flows... - Inspect... Read more

After ignoring for a couple of years that the bearings were bad on our Whirlpool Cabrio washer and just closing the door to the laundry room, it started slinging grease underneath during the spin cycle. Knowing that the cost to call out a repairman would be close to the cost of a new washer, I decided that it would be a nice Saturday project after reviewing AppliancePartsPros’ repair video. The bearing & tub seal kit and bearing installation tool arrived in two days. I’ve done a lot of... Read more

Touch up paint Read more

Replaced It With New One Read more

• Will not stop filling with water
• Leaking

First off I have to say that Appliance Parts Pro's saved me from hiring a repair person, and quite possibly just getting rid of my washing machine. Their video's helped out SOOOOOOOO much and the advice one of their agents gave me over their online chat helped me trouble shoot something when I got stuck. On top of this they shipped my parts fast enough that less than 12 hrs later they arrived, which allowed me to get my machine up and running way faster than the other options I had available.... Read more

I noticed when we would run washer water would stay in tub. Pump would hum but not pump water out. Layed washer on its belly . Pump was at bottom of washer. Easy access . Removed 3 screws,2 wires , & 2 hose clamps. Didn't have to call Maytag Repair man. Easy Read more

Replaced suspension rods and worn absorber pads Read more

I had to cut the old agitator out with an oscillating saw in order to access the agitator drive. This is the second Maytag (MVWC 565) I have had to do this to. I first tried removing it by sliding straps under the agitator then then using a jack to pull it loose which did not work either time. One suggestion I have would be to remove debris from tub as you cut in order to prevent it from dropping from the inner tub into the outer tub. Read more

This was actually one of the easiest fixes I’ve done. All that was required was to remove 3 screws to remove the broken part. I used a pair of pliers to remove the moisture sensors from the broken part to the new one. Read more

• Leaking

We ordered parts from appliance parts pros and I fixed it. Read more