Zisb480dma20dmb Parts

I bought two parts. The dispenser housing shield and the funnel ice dispenser. I watched the short video on how to put it back together and I was done in just a matter of minutes. The video was such a big help. I forgot how the spring went on and was able to watch the video and put it back together in just a matter of minutes. I know I must have saved a couple of hundred dollars on a service call. Read more

• Won't start
• Freezer section too warm

Replaced overload, and capacitor Read more

Took out old damper which had a broken flap door. Put in the new damper and fridge worked good as new. Read more

I replace the water inlet valve in my refrigerator about 8 months ago. About a week ago, the old plastic water line broke. I forgot how the water line connector worked and broke the valve trying to pull it out. I got a new valve and replacement water line, and it went in easily, just like the video said. Morals of the story: 1. Know how to remove the old plastic water line. I could have saved myself the price of a new valve if I'd remembered how the connector worked. Unless you have a really... Read more

• Noisy

Condenser fan stopped on my big 2003 Monogram 4 foot wide ZIS480D Refrigerator. It is top mounted. The fridge had to be rolled out. 20 screws removed and the top sheet metal to get at the condenser. That was the only way to get at it. Works like new now. Read more

Replaced the water supply valve...boom! Read more

• Light not working

When diagnosing the problem, I discovered that the ice door was not properly sealing and that the solenoid had appeared to rust/corrode forcing the door open. I replaced most of the ice dispenser internals (solenoid, crank, door, and spring) following the video. The door will now open when dispensing ice (which it does!), and will oddly stay open for a few seconds once I am finished, but does seal properly and the chute/container no longer frosts over. Read more

I watched the help videos first, then ordered the parts, and installed all items as in the video. Read more

Firstly, the Ice Door had a kink in the edge, which caused it to stay open and create lots of frost on the coils. $5.00 part, highly recommend it. (By the way, the new door was little too big and it too stay propped open and left a gap so I had to trim the top edge of the rubber with scissors to get it to fully close.) Secondly, there are two heaters for the defrost cycle, one that goes around the coils and another attached to a collector pan beneath the coils. When the cycle hits, those... Read more

Spliced new and old power cord near the connections in the fridge and connected them. Didn't mess with the factory harnesses or connections inside actual fridge. Read more

Very easy fix -- remove the old, and attach the new. Read more

I replaced the fan and heater element. The replacement was not an exact match. I had to adjust the parts to get the harness to fit the plug was not the correct size. I cut it off and used the existing plug. Not a big deal and everything else fit. Pretty good for a twenty year old replacement. Also the heater element was a different shape but it fit as is. Read more

Ordered the new interface display - this must be the easiest refrigerator repair possible. My version popped right off without even a screw (some models have a screw). There are 3 different sizes of connector to disconnect and hook up to the new board - so you really can't mess that up. Read more

The problem was most likely the evaporator fan motor but it could have been a bad blade, loose parts or bad motor mounts. Hard to tell without taking everything apart and inspecting. Since fridge was 17 years old I decided to order the entire evaporator fan assembly as shown in the parts diagram including fan blade, motor brackets, motor, motor mounts, screws, etc. Getting to the assembly involved removing the ice maker unit plus the entire rear inside of the freezer section. Parts cost around... Read more

Replaced dispenser kit and auger. Repair videos were a great help and resolved potential problems that I usually solved by trial and error. Thanks, Appliance Part Pros! Read more