Hardware Hand Small Engine On-Off Switch Parts
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10411934
Fix burners stuck on high or heating out of control with this infinite switch. Controls single, dual, or triple element burners. Easy DIY repair.
Do-It-Yourself Stories from Customers like You
Front two burners were heating out of control Garrey P. • Rogers , TX • December 11, 2018
Replaced two switches that controlled two front burners. One controlled three different burner sizes options in one burner. The other was the speed burner, basically three different burner options in one burner.
Read more
More
$78.65
- Compare At:
-
$93.59
- You Save:
-
$14.94
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3398094
Dryer won't start when you press the button? The start switch sends the signal to begin the cycle. Simple 5-10 minute fix with basic tools.
Do-It-Yourself Stories from Customers like You
Dryer wouldn't start John D. • Reno , NV • August 14, 2015
Thermal fuse
Read more
More
$61.56
- Compare At:
-
$73.87
- You Save:
-
$12.31
Genuine Whirlpool part
By: Whirlpool
Part Number: W10211974
This door interlock switch is a safety micro switch that detects whether the microwave door is properly closed before allowing the unit to operate. It is a small, snap-action switch mounted near the door latch mechanism. Replace this switch if the microwave won't start, runs with the door open, or blows a fuse when the door is closed.
Do-It-Yourself Stories from Customers like You
Door latch broke also causing the fuse to blow James M. • Ocean View , NJ • April 28, 2017
It is difficult (if not impossible) to remove the electronic switches from the hard
plastic latches. I replaced all three switches and both the upper and lower latches I also replaced the main 20 amp ceramic fuse which blew out when the latch/switches failed.
Read more
More
$46.35
- Compare At:
-
$55.16
- You Save:
-
$8.81
Genuine Frigidaire part
By: Frigidaire
Part Number: 5304505436
Fix E11 error code and washer not filling issues. This pressure sensor switch monitors water levels and signals the control board. DIY repair in under an hour.
Do-It-Yourself Stories from Customers like You
Washer would not let hot or cold water in diagnostic tests. Allowed both hot and cold water in had 120v on 5vdc fill sensor. Wayne K. • Stockbridge , MI • March 21, 2020
Replaced fill sensor and Main control board. Payed next day shipping and washer was up and running an hour after receiving the parts.
Read more
More
$53.95
- Compare At:
-
$64.20
- You Save:
-
$10.25
Genuine Ge part
By: Ge
Part Number: WB24T10058
Burner stays on high or won't turn off completely? This infinite control switch regulates surface burner heat. Simple 10-minute DIY fix with video guide.
Do-It-Yourself Stories from Customers like You
Bad burner switch James C. • Augusta , NJ • January 04, 2015
I first checked a repair video and found the procedure was a 10 minute job. I then went to the website, put in my stove model number and searched for the switch. While I was looking I was offered a chat session with one of their experts. I am glad that I accepted. The switch I was looking at was not the right switch for the job. My expert verified my model number and the switch that need to be replaced. After a couple of minutes, she came back with the right part and placed the order for...
Read more
More
$108.95
- Compare At:
-
$130.74
- You Save:
-
$21.79
Genuine Whirlpool part
By: Whirlpool
Part Number: W11457217
Freezer or fridge light not working? Door alarm going off? This door switch detects when doors open/close to control lights. Easy 15-minute fix.
Do-It-Yourself Stories from Customers like You
No freezer light Pedro J. • Kissimmee , FL • May 14, 2018
Ordered the freezer door switch and the light. Replaced the freezer door switch and the light and everything is back to normal. Replaced both in less than 15 min with no problems.
Read more
More
$31.59
- Compare At:
-
$37.91
- You Save:
-
$6.32
Genuine Whirlpool part
By: Whirlpool
Part Number: W11545764
Fix dishwasher overflow or no-fill issues with a float switch replacement. Detects water levels and prevents floods. Simple repair for most DIYers.
Do-It-Yourself Stories from Customers like You
H20 Steven Y. • North Las Vegas , NV • September 04, 2026
Tested float and input valve ohms both out of range replaced both parts units 3 years old
Both parts did not fix problem
Read more
More
$27.37
- Compare At:
-
$32.30
- You Save:
-
$4.93
Genuine Whirlpool part
By: Whirlpool
Part Number: 8193506
Dishwasher leaking from underneath? The float switch kit controls water level and stops overfilling. Typical repair time 10-30 minutes.
Do-It-Yourself Stories from Customers like You
Kitchenaid dishwasher kudp02frss2 leak at float switch at front right of unit Richard B. • Mahwah , NJ • December 02, 2016
Removed bottom cover, located leak at float switch, removed and replaced float switch kit.
The toughest part of the repair was removing the Float & Retainer Assembly (in the interior of the machine tank) which broke when I pushed it back and pulled it straight up as suggested in the service manual. The Float Switch Kit (attached to, and below the float, below and outside the tank) has a folding plastic cover which fastens with plastic clips. If you open the switch kit before removing the...
Read more
More
$92.63
- Compare At:
-
$109.30
- You Save:
-
$16.67
Genuine Frigidaire part
By: Frigidaire
Part Number: 134399700
The Start Switch is an OEM replacement part for Frigidaire dryers. This part initiates the dryer's cycle once the user selects the desired settings. By pressing the start switch, the motor activates, and the drying process begins, ensuring clothes are dried according to the selected specifications.
Symptoms of a bad Start Switch include:
- The dryer not starting when the switch is pressed
- Intermittent starting issues, where the dryer sometimes starts and sometimes doesn’t
- The need to hold the switch in place to keep the dryer running
- Unusual noises when the switch is pressed
Causes for a malfunctioning Start Switch can include electrical issues, such as faulty wiring or connections, wear and tear from frequent use, or internal failures within the switch mechanism that prevent it from signaling the motor to start.
This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore dryers.
Do-It-Yourself Stories from Customers like You
Start switch knob broke off. Jeff O. • Laurier , WA • March 07, 2018
I went online, ordered the part and installed it,,, took 15 minutes to install,,,saved huge $$$
easy peasy!! :-)
Read more
More
$77.66
- Compare At:
-
$91.64
- You Save:
-
$13.98
Genuine Samsung part
By: Samsung
Part Number: DA34-00011B
Fix a refrigerator that won't dispense water or ice with this dispenser switch. Requires removing the display cover and disconnecting housing connectors.
Do-It-Yourself Stories from Customers like You
There was no water dispensed and one led was burned out Ralph T. • Fishers , IN • August 15, 2016
I replaced the control board and the microswitch.
Read more
More
$30.76
- Compare At:
-
$36.91
- You Save:
-
$6.15
Genuine Whirlpool part
By: Whirlpool
Part Number: W10337780
Washer overfilling or not filling correctly? This water level pressure switch kit fixes fill issues. Includes switch, tube, and clamp. Easy DIY repair.
This part fixes the following symptoms
-
Will not stop filling with water
-
Will not fill with water
See more...
Do-It-Yourself Stories from Customers like You
Washer overfilling David C. • Pine Mtn. Club , CA • May 09, 2014
Reviewed troubleshooting tips and identified problem as "water level switch".
Watched repair video, which was very helpful.
Ordered part on a Sunday, which arrived the following Tuesday.
Repair was easy the fix was successful.
Read more
More
$62.46
- Compare At:
-
$74.95
- You Save:
-
$12.49
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3399639
Dryer not heating or stuck on one temperature? This temperature selector switch controls heat settings. Moderate DIY repair with video guide available.
Do-It-Yourself Stories from Customers like You
1 no heat on high or low settings and sometimes on medium heat setting 2 no auto cool down Robert H. • Renton , WA • March 11, 2015
I replaced the cycle switch, fixing the lack of heat. The timer switch replacement fixed the auto cool down. I watched a cycle switch replacement on Youtube, demonstrating removal of the top console, which answered the only question I had about the repair. The timer switch was a hundred bucks. The only thing to be said about that is that it was a lot cheaper than a repairman or replacing the dryer.
Read more
More
$59.48
- Compare At:
-
$71.38
- You Save:
-
$11.90
Genuine Whirlpool part
By: Whirlpool
Part Number: WP74010824
If your large burner won't heat or stay at the right temperature, the element switch likely needs replacement. Simple 10-15 minute repair with a screwdriver.
Do-It-Yourself Stories from Customers like You
The jennaire stove has a switch with a very poorly designed knob it catches on people's clothes and breaks off Bernard N. • West Linn , OR • December 06, 2016
You have to take the knob off the broken part, then buy the new switch element and fix it. To do this you turn the power off, take out 6 fasteners to release the front panel of the stove and replace the switch element. Then put it all back together. Very simple. But if the knob was designed better it would not have broken in the first place. It looks nice, but this is the third time I have had to fix one.
Read more
More
$78.71
- Compare At:
-
$93.66
- You Save:
-
$14.95
Genuine Whirlpool part
By: Whirlpool
Part Number: W10777162
The Screw is an OEM part for Whirlpool ranges. This screw is used to secure various components within the range, ensuring that parts such as panels, control boards, or burners are firmly attached and remain stable during operation.
Causes of a bad range screw can include regular wear and tear, over-tightening, or exposure to high heat.
Symptoms of a bad range screw include:
- Loose or unstable components within the range
- Difficulty in securing parts during maintenance or repair
- Visible damage or wear on the screw
- Parts becoming misaligned or rattling during operation
This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.
Do-It-Yourself Stories from Customers like You
Left door hinge would not allow door to close square to opening Jay R. • Clearwater , FL • October 19, 2019
Replaced the hinge receiver with a new one. The old one was bent slightly inside where it could not be seen. I think someone pushed the door down to far or fell on it. 2 screws to remove it, take out storage drawer and reach up little ways to remove and replace the receiver. Replace the 2 screws. The receiver comes with 2 screws but I ordered an extra ( never used it ). The sides of the receiver were spread just a tiny bit but were enough to cause a problem.
Read more
More
$7.56
- Compare At:
-
$8.90
- You Save:
-
$1.34
Genuine Ge part
By: Ge
Part Number: WB18X23942
If your gas cooktop burners won't ignite or igniters click continuously, the switch harness may be faulty. Moderate DIY repair with basic tools.
Do-It-Yourself Stories from Customers like You
No spark or red led gas cooktop working with a lighter. Devang R. • San Ramon , CA • June 23, 2022
The ordeal began after wiping around burner knobs with a moist paper towel with cleaner and wrapping the towel around the burner knob shaft to clean around it. The cooktop stopped sparking on all the 5 burners and no red LED light. There was gas flow and I could light the burner using a lighter. I looked up and found a couple of good youtube videos on troubleshooting and also came upon the AppliancePartsPros.com site. I opened the cooktop (youtube video helped) after turning off the gas supply...
Read more
More
$46.33
- Compare At:
-
$55.60
- You Save:
-
$9.27
Genuine Ge part
By: Ge
Part Number: WE4X782
Fix a dryer that won't start or has a broken start knob. This rotary start switch is located in the control panel. Easy 5-10 minute DIY repair.
Do-It-Yourself Stories from Customers like You
Dryer knob broke 8 years ago post finally wore down so it could not be turned with pliers Patrick H. • Saint Albans , VT • December 29, 2014
Ordered parts arrived in two days. Ten minute fix with one wrench. Should have done it years ago.
Read more
More
$73.73
- Compare At:
-
$87.74
- You Save:
-
$14.01