Need Help?
Call
Fix a dryer that won't shut off or runs continuously. This timer controls cycle timing and automatic shutoff. Most DIYers complete in 15-30 minutes.
Installed this part and it was working good as new in 15 minutes! Read more
Dryer stops mid-cycle or won't heat properly? A faulty timer often causes these issues. This timer controls cycle progression and heating phases.
Purchased a new timer from applianceParts Pros. Simple replacement took 15 minutes, dryer is running like new again. Also, defective timer made in china, new replacement made in USA. It just doesn't get any better than that! Read more
Fixes washer stuck in cycle, won't drain, or won't turn on issues. Restores automatic cycle transitions and water fill control. 15-minute DIY repair.
The error code implies a faulty fill valve. This was not the case for me. Replacing the main PCB assembly solved the problem. I have run two full loads since the repair with no problems. Read more
Fix a dishwasher that won't start or has no power with a new control board. This part coordinates all cycle functions and monitors safety features.
Display would flicker "Delay" light and then shut down. Replaced control board and door switch. Read more
Fix unresponsive buttons, cycles that won't start, or blinking lights. This user interface board restores control panel function in about 30 minutes.
1. Turn off the electricity to the dishwasher 2. Unscrew all of the screws on the inside of the dishwasher door. 3. Take off the door and put it aside 4. Loosen the panel that contains the control board, control panel and the door lock mechanism 5. Using a screw driver, push in the small moveable tab in the center of the plastic clip that is holding the control board to the plastic panel. 6. Unhook the ribbon that is attached to the bad control board. 7. Attach the ribbon to the new control... Read more
This is the main electronic control board that manages the washer's cycles, motor operation, water levels, and other key functions. It receives input from the user interface and sends signals to the various components to run each wash cycle properly. Replace this board if the washer fails to start, stops mid-cycle, displays error codes, or exhibits erratic behavior that is not caused by a faulty sensor or wiring issue.
This is the electronic phase control board that regulates the motor speed in a stand mixer. It adjusts power delivery to the motor based on the speed setting selected by the user. Replace this board if the mixer runs at only one speed, does not respond to speed adjustments, intermittently stops during operation, or fails to turn on entirely.
I replaced the Board-Phas and speed control plate since power was not making it to the motor. When I received the speed control plate it had nuts on the upper screws with springs, since my old one didn't have nuts I assumed that the nuts were to keep the springs on until installed. After putting it back together, I noticed that though it worked, the first two settings did nothing. Now, guys, I was desperate, OK. I downloaded the service manual and read it from front to back, and when I got to... Read more
Fix burners that won't ignite, slow clicking, or repeated sparking. This spark module controls ignition for gas range surface burners and oven.
Replaced ignitor. Watch the u-tube videos for removing and replacing the board and ignitor. Read more
Fix a washer that won't advance through cycles, stops mid-wash, or skips stages. This mechanical timer controls wash, rinse, and spin sequences.
Took out old timer, and upon inspection notice some electrical arcing( burned areas). I installed new timer and worked perfectly. Problem was that it would fill up with water, but after it was filled the timer kept going but washer was not agitating. Only thing that worked was delicates wash. Important Disconnect/ unplug power cord! 1. Remove knob, center cap pops off revealing a pin. Slide that off and the knob should come off. 2. Removing knob should reveal 2 socket screws remove... Read more
Inner tub basket holds clothing during wash cycles. Replace if cracked, rusty, or broken. Installs in center of washer between outer tub and agitator.
Ordered the parts from AppliancePartsPros - super fast shipping, and even though I opted for regular shipping all of my parts arrived the very next day, including the big and bulky inner basket. Disassembly went smoothly, simply following the directions in the AppliancePartsPros video. The only problem I had was that the inner basket simply would NOT come of the drive block no matter what I did. Struggled for a few hours trying to take it off. Then, I called AppliancePartsPros and they said it... Read more
Fix unresponsive oven controls or blank displays with a new electronic control board. Restores temperature settings and cycle functions on gas ranges.
Fix a washer that won't advance through cycles or stops mid-cycle. This timer controls cycle duration and sequencing in your washer dryer combo unit.
Replace timer; remove lid switch Read more
This is an electronic noise filter assembly that mounts on the dishwasher's power supply line. It suppresses electromagnetic interference generated by the dishwasher's motor and electronic controls, preventing it from affecting other appliances or electronics on the same circuit. Replace this part if the dishwasher trips breakers, fails to power on, or if you notice electrical interference with nearby devices when the dishwasher is running.
Replaced noise filter. Read more
Oven won't heat, display blank, or controls unresponsive? Replace the electronic control board. DIY-friendly repair, typically 30 minutes with basic tools.
Replaced with part No.AP4417276 electronic control board that we ordered from you and replaced it ourselves with your professional assistance. This has been an excellent experience with your company, and your return policy. Thank you . Read more
If your washer won't shut off or won't advance through cycles, the timer may have failed. This repair typically takes 10-15 minutes with basic tools.
Easy. Opened the front panel, removed the timer, went on line with the part number. Part arrived the next day and I installed it in 2 minutes. FIXED. Read more
This electronic control board with overlay manages your range or wall oven's heating and user interface. Replacing a failing control restores accurate temperature regulation, proper bake/broil operation, and a readable display so the appliance responds as it should.
I first tested and replaced the temperature sensor. Since this is a slide-in range, I managed to pull it out just enough to access the back without disconnecting the downdraft and gas line. (For wall models this would not be the case.) Unfortunately, that did not do it. Next I replaced the lower heating element because it was a little below the ohms level it should be at. No go. So far, both of these were pretty easy to do and were relatively inexpensive so I wasn't too frustrated. Then I... Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.