Assy-Case Sensor Parts

Thermal fuse that protects the washer motor circuit from overheating. Interrupts power if motor temperature exceeds safe limits. Replace if washer stops mid-cycle or won't start.

Oven won't heat or stops heating? This thermal fuse thermostat opens the circuit at unsafe temperatures. Common fix after self-clean mode failures.

Oven shuts off at high temperature or won't heat? This high-limit safety thermostat may have failed. Restores normal heating. Easy DIY fix in 30 minutes.

This kit includes a replacement heating element and a high limit thermostat for an electric dryer. The heating element generates the hot air that dries your clothes, while the high limit thermostat acts as a safety device to prevent overheating. Replace this kit if your dryer is not producing heat, takes too long to dry clothes, or shuts off prematurely due to overheating.

This temperature sensor mounts on the sealed-system gas inlet line in compatible refrigerators. It relays precise temperature feedback to the control so cooling and defrost cycles are managed correctly, helping maintain stable compartment temperatures. What it does:

• Senses temperature at the gas-inlet line; resistance changes are read by the control
• Helps regulate compressor, fan, and valve operation for proper cooling performance
• A failed sensor may cause erratic temperatures or extended run times
• Can correlate with control thermistor error codes or frost/ice patterns near the evaporator

• 1 thermistor sensor

• Disconnect power before servicing
• Note original sensor placement and insulation; reinstall in the same location and orientation
• Attach the sensor firmly to the line and route the harness as originally, away from sharp, hot, or moving parts
• Do not open or puncture sealed-system tubing; if damage is suspected, stop.

Fix sensor cook cycles that won't adjust properly or show sensor errors. This humidity sensor monitors moisture levels for automatic cooking adjustments.

Fix dryer that won't stop or shows tO error code. This moisture sensor assembly monitors drying cycles. Moderate DIY repair, 30-45 minutes.

This thermistor is a temperature sensor that monitors conditions in your refrigerator and sends signals to the control board to regulate cooling cycles. It ensures your refrigerator maintains the correct temperature for food safety and energy efficiency. Replace this sensor if your refrigerator is running too warm or cold, cycling on and off frequently, or displaying temperature error codes.

Fix oven overheating or F9 error codes with a thermal limit switch replacement. This safety shutoff prevents damage when temperature exceeds safe limits.

Fix frost buildup and warm fridge temps. This defrost thermostat monitors evaporator temperature to prevent overheating during defrost cycles.

This thermistor is the dishwasher's temperature sensor. It reports water temperature to the control so the heater and cycle timing are managed correctly, helping restore reliable wash performance and more consistent drying.

• Monitors water temperature in the tub/sump and sends readings to the control board
• Helps the control regulate heater operation and determine cycle progress/timing
• Failure can result in no heat or poor drying
• May cause unusually long/short cycles or temperature-related fault codes

• Disconnect power at the breaker and shut off the water supply before servicing
• Access is typically from the toe-kick/base area or sump; remove the lower access panel as needed
• Release the locking tab/clip, remove the sensor, and ensure the existing seal/O-ring is properly seated; install the new sensor fully to prevent leaks
• Reconnect the wire harness, restore power, and run a test cycle to check for leaks and proper heating

The Thermistor is an OEM Replacement Part that maintains the temperature inside your Frigidaire refrigerator. This thermistor handles reading the internal temperature. After reading, it transmits this information to the control system. At a temperature of 29 degrees, the thermistor should exhibit a resistance of about 35k ohms. While at room temperature, it should read approximately 5k ohms.

Causes of a bad thermistor can include regular wear and tear, exposure to moisture, or electrical issues. Over time, the thermistor may become less accurate or stop working altogether.

Symptoms of a bad thermistor include:

• Inconsistent or incorrect temperature readings
• The refrigerator being too warm or too cold
• The cooling system running continuously or not at all
• Error codes related to temperature control

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

Dryer not heating or overheating? A faulty temperature control thermostat often causes inconsistent heat cycles. This part regulates dryer temperature.

Refrigerator not cooling properly or showing temperature errors? This temperature sensor monitors compartment temps and sends readings to the control board.

This is a high limit thermostat that monitors the temperature inside the dryer's heating chamber and shuts off the heating element if temperatures exceed a safe threshold. It serves as a safety device to prevent overheating and potential fire hazards. Replace this thermostat if your dryer is not heating at all, shuts off prematurely, or if a multimeter test shows no continuity through the thermostat.

Fix a warm fridge or melting freezer ice cream. This defrost thermostat monitors evaporator temperature to prevent frost buildup and restore proper cooling.