Small Engine Safety Switch Parts
Genuine Ge part
By: Ge
Part Number: WE4M411
Dryer won't heat or overheating? The temperature switch controls heat settings. DIY-friendly repair—just swap wires and reassemble. Takes 20 minutes.
Do-It-Yourself Stories from Customers like You
The timer was sticking to the point where the knobs were stripping out Peter A. • Dallas , OR • December 16, 2014
I unscrewed the 3 Phillips screws on the back of the dryer controls housing, then it folds forward for access to each control switch. the old one popped out, and I swapped the wires using a needle nose pliers, one by one, from the old switch to the new switch. The part was an exact fit, and popped right back into the housing. I screwed the 3 screws back in, pushed on the new knob, and it looks and works like new !
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WP22001656
This is the washer's water level switch that senses tub level via air pressure and provides five selectable fill settings. Replacing a failed switch restores accurate filling and lets the cycle advance properly through wash, rinse, and spin.
- Monitors air pressure from the tub to detect actual water level
- Controls the inlet valves to start/stop filling at the selected setting
- Signals the timer/control to begin agitation and advance the cycle once full
- Common symptoms: overfilling or water keeps running, stops filling too soon or won't fill, inconsistent water levels, cycle won't advance due to incorrect level detection
What's included: 1 water level pressure switch with 5-position rotary selector Install notes:
- Disconnect power and turn off water supply before servicing
- Access the control console; remove the selector knob/dial and panel as needed
- Note wire locations (take a photo), move the harness, and transfer the pressure hose; ensure the hose is clear and firmly seated
- Securely mount the new switch, reassemble the console/knob, restore utilities, and test each fill level
Do-It-Yourself Stories from Customers like You
Water level in Maytag washer was always high and was not adjustable Von D. • San Bernardino , CA • December 21, 2017
Replaced the water level switch and water level pressure switch hose. Video on AppliancePartsPros.com detailed the procedure.
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WP4387911
Fix a refrigerator light that won't turn on or off when you open the door. This push-button switch senses door position. DIY repair in 30 minutes.
Do-It-Yourself Stories from Customers like You
A failed freezer door switch was causing the fridge to display that the door was open when it was not this caused it to beep at random Kara H. • Charleston , SC • March 08, 2016
We actually were able to determine that one of the freezer switches was bad and taped it down for about 3 days. The beeping stopped. Our fridge has two freezer switches and one fridge side switch. I ordered all three from these guys. They were cheaper than Whirlpool by about $20 for parts and about $15 for shipping. The part numbers had superseded too many times to count, usually that doesn't matter but in this case it did. The new parts were just slightly bigger than the old parts AND...
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WP9763761
If your range burner won't heat, cycles incorrectly, or buzzes when turned on, a faulty infinite switch is likely the cause. Moderately easy DIY repair.
Do-It-Yourself Stories from Customers like You
Stems were broken on handles. Knobs didn't work correctly. Dan R. • Glendale , CA • May 06, 2020
Had to replace both switches. The hard part was getting the control panel off to get access. Only a few screws but even after getting them out, really struggled getting it off. After getting off, discovered that you need to get it lifted up before pulling it off.
Read more
More
Genuine Frigidaire part
By: Frigidaire
Part Number: 318394803
Has three terminals.
Do-It-Yourself Stories from Customers like You
Oven light stayed on when door was closed Robert S. • Jacksonville , IL • June 14, 2015
When trouble shooting the problem I found that the light switch housing outer lip was broken allowing the switch to push through mounting surface behind the oven door. This is a slide in range so, I proceeded to pull the range away from the counter where I could unplug the power cord. Once the power was off like located the panel on the right upper side of the unit and removed the screws to allow access to the switch. I then unplugged the switch from the wiring harness and removed the damaged...
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: 9871829
Fix a compactor that won't start, stops mid-cycle, or requires holding the pedal down. This drawer tilt switch is a quick 15-second replacement.
Do-It-Yourself Stories from Customers like You
Compactor would start sometimes by just closing the door when you start it by normally lifting the pedal it would not stop at the end of it's cycle Bruce H. • Hewitt , NJ • January 19, 2015
I replaced the upper switch that contacts the door in a closed position and more important the start switch contacted by lifting the start pedal.
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: W11206737
Fix a range hood control knob that stops responding or only works in one position. This rotary switch restores precise fan and light selection.
More
Genuine Ge part
By: Ge
Part Number: WB24X10110
Fix a range hood fan that won't turn on or off, or lights that don't respond to controls. This motor/lamp switch restores on/off control. Moderate DIY.
Do-It-Yourself Stories from Customers like You
Broken fan switch William S. • Marco Island , FL • October 02, 2015
Biggest problem was trying to get at the switch to replace it. Had to remove two allen head screws to gain access on the back panel of the range hood. The allen heads were very small fortunately I had a number bits from my old electric screw driver that allowed me to remove them. Even then I had to snake my way cutting my hand to get to the switch to replace it.
The positive part the switch was over $25 less the if purchased directly from GE through Appliance Pros.
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3399640
Dryer won't heat or overheats on low settings? A faulty temperature selector switch prevents proper heat control. Easy DIY fix in 10-15 minutes.
Do-It-Yourself Stories from Customers like You
Dead no power. Peter W. • Northfield , IL • January 29, 2024
APPs stellar videos got me started with confidence. Your parts diagram exactly match mine for my 28 year old Sears Kenmore Gas Model 110-97588210 (75882). Teacher at TMM Appliance convinced me to approach from the simpler, cheaper, easier to access parts inwards using the wiring diagram. I’ve designed products for Klein, Halo, and JUNO but am just an advanced electrical amateur. 3 parts totaling $110 and two hours and it runs and heats to spec. Even had time to vacuum out all over the lower...
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10285512
Fix erratic or unresponsive cycle selections with this laundry center rotary encoder switch. Mounts behind the cycle knob to restore accurate settings.
Do-It-Yourself Stories from Customers like You
Temperature control switch failed to cold only. Marilyn M. • Summerfield , FL • September 30, 2017
Replaced with a new one.
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: 279872
This fixed-value resistor is an electrical component used in select dryers to limit current in a specific control circuit. It helps the timer or electronic control operate correctly by dropping voltage to safe, design-intended levels.
- Provides precise resistance to reduce voltage/current in the designated dryer circuit
- Supports proper operation of the timer, control board, or end-of-cycle signal (varies by model)
- Failure may present as a timer that won't advance, an inoperative signal/buzzer, or irregular cycle behavior
- Replace if visibly burned/damaged or if testing shows an open or shorted condition
What's included: One resistor Install notes:
- Disconnect power to the appliance before servicing
- Access the console/wiring harness and note original wire routing
- Make secure, insulated connections and route the resistor/leads exactly as original to avoid heat or chafing
- After installation, run a test cycle to ensure proper operation of the affected function
Do-It-Yourself Stories from Customers like You
Timer wouldn't advance on my dryer John L. • Oblong , IL • March 22, 2016
I ordered a new timer and installed it with the help of the videos provided and this did not solve my problem so I chated with the pros @ Appliance Parts Pros and told them my problem and they told me the problem and recommended the part I needed and With the incredibly fast shipping I had the part the next day. I installed it and now my dryer timer works great.Thanks to APPs for their help and ease of ordering and fast shipping. I highly recommend AppliancePartPros and will definitely use...
Read more
More
Genuine Lg part
By: Lg
Part Number: EBF60662911
This is a spark ignition switch assembly with wiring harness that controls the electric igniters on a gas range cooktop. It sends voltage to the spark modules when a burner knob is turned, initiating the clicking ignition sequence. Replace this part if your burners won't spark when turned on, spark continuously even when knobs are in the off position, or if only some burners ignite properly.
This part fixes the following symptoms
-
Doesn't shut off
-
Gas igniter glows, but will not light
See more...
Do-It-Yourself Stories from Customers like You
All the igniters spontaneously began to fire Michael S. • Adams , NY • October 12, 2019
Found a YouTube video online that provided instruction on how to change out the part.
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10274880
Fix a dishwasher that stops mid-cycle with a blinking start light. This door interlock switch restores reliable operation. 20-minute DIY repair.
Do-It-Yourself Stories from Customers like You
Kenmore ultra wash dishwasher worked great for 18 months; then would not run start button blinked 3 times and nothing happened Nick C. • Safety Harbor , FL • November 12, 2015
Looked online, appeared to be door switch or control panel. Tried door switch first, a $30 part. Installed new door switch and washer started right up and appears to be fixed. Have not tried full wash cycle yet, but problem appears to be fixed. I decided to buy part from AppliancePartsPros.com because I could return the part if it did not correct the problem, no one else offered such a deal. I will only deal with AppliancePartsPros in the future, they were extremely helpful on the phone!
Read more
More
Genuine Frigidaire part
By: Frigidaire
Part Number: 216594300
The Starter is an OEM replacement part for Frigidaire refrigerators. This component is crucial for initiating the compressor, which is responsible for cooling the refrigerator. The starter works by providing the necessary electrical power to get the compressor running, ensuring that the refrigerator maintains the correct temperature.
Causes of a bad starter can include electrical malfunctions, wear and tear over time, or damage from power surges. A faulty starter can prevent the compressor from starting, leading to cooling issues.
Symptoms of a bad Starter include:
- The refrigerator not cooling properly
- The compressor not running or frequently cycling on and off
- Unusual clicking or buzzing noises from the compressor area
- The refrigerator being warmer than usual or food spoiling quickly
This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.
Do-It-Yourself Stories from Customers like You
Overload protector done its job we had not defrosted the freezer for a long time causing the compressor to run more than it should it got overloaded found it defrosting Wanda L. • Belle Rose , LA • December 09, 2014
First checked the power then took off the compresser connections cover looked for burnt wires or loose or disconnected wires they were none of those I then removed the wires from the starter an overload protector removed them checked both for contunuaty overload protector no contunuaty then I checked the 3 poles on the comp. for contunuaty they were ok then I checked each pole to ground on the com. to final check that the comp. was still good
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WP74011489
Fixes burner that won't heat or indicator light stuck on. This infinite switch controls surface burner power and heat settings. Moderate DIY repair.
Do-It-Yourself Stories from Customers like You
Knob twisted off Glenn M. • Aurora , OR • August 20, 2018
Replaced switch
Read more
More
Genuine Frigidaire part
By: Frigidaire
Part Number: 5304525097
Fix water or ice dispenser not working with this 4-button control switch assembly. Common fix when buttons fail to respond or dispense incorrectly.
Do-It-Yourself Stories from Customers like You
No water from dispenser. Steve N. • Malverne , NY • April 10, 2021
Replaced the four-button switch assembly.
Read more
More