Procom Heater Parts

• Not drying dishes properly
• lights flashing or blinking

Number one was turn the power to the dishwasher off. I disconnected the hoses under the sink. The dishwasher had to be pulled out from the cabinet. The old heating element easily came out and the new one put in its place. The instructional video made the repair very easy. Read more

Replaced the heater unit because the heater coil had burned in two. The whole project took less that one hour. I also replaced the dryer timer since one of the cycles would not cool down as part of the process. Read more

Replaced defrost heater and temperature sensor. Read more

I used my experience with appliances to help me replace these parts. I also used the available AppliancePartsPros.com videos that were supplied by your email with my order. The videos are very helpful. Read more

First guess was the Bake Element, but I ran my hands around it and didn't feel any clue of a break/failure in the element. Further research indicated that the Hot Wire Relay is the next likely cause, that was really bad news because that part is unavailable anywhere. Swapped the H1 and H2 wires on the Hot Wire Relay, and found that Broil still worked, which indicated that the relay was good and the Bake Element was the likely cause. This was good news because that Hot Wire Relay is made... Read more

First, I just unscrewed all nuts that are holding the frame and all surface elements. Once all parts, surface elements, control switches, are loose from the original glass, I just moved all parts to the new glass. Due to the weight of the glass, all actions have to be done carefully as I broken one corner of the glass couple of years ago when I replaced one of the control switch. Read more

I reconnected the heating element by hand and inserted the new oven racks without using any tools. Read more

After watching numerous videos I was able to discern that the problem was with one of the following: the timer, the heater, or the thermostat. a short time check showed me that the timer was working so that narrowed it down to the other two. Not having the necessary tools to check those two I ordered both parts. Once the parts came and I took out the old parts it was quite evident that it was the heater since it had black burn marks on it. I decided to install the thermostat also since it... Read more

Se above Read more

I ordered the both the Pcb assembly and a heater sheath. Upon accessing the Pcb, I immediately discovered it had failed miserably, (contacts burnt and melted, wiring and insulation on one wire suffered severe electrical damage. To put it bluntly a small electrical fire had occurred on the circuit board. There was enough slack in the damaged wire so I removed the affected area, replaced the terminal. Replacing the Pcb was a snap. Disconnect the power, remove the rear cover, prior to removing... Read more

Easy fix, took out the screws and disconnected the element. Make sure you unplug the oven!! replaced it with the new elements. oven is working good. Read more

Yes. Since I was replacing the heating element I decided to replace the fuses and thermostat. I ordered and installed the parts I purchased from Appliance Parts Pros and the dryer works great. Read more

Installed replacement burner. Not a one-to-one fit where the wiring is concerned but everything needed to effect the change out was provided with the part. It is important to make notes of what was connected to what on the old one and to compare that to the new one. I used a download of the wiring diagram to good effect because it has the color code for the wiring on it. I am an engineer and can read such things which the average DIY'r might not be able to do so the notes will help. The... Read more

New part clipped right in. Tightened 2 screws and was done in 5 minutes. Read more

Firstly, the Ice Door had a kink in the edge, which caused it to stay open and create lots of frost on the coils. $5.00 part, highly recommend it. (By the way, the new door was little too big and it too stay propped open and left a gap so I had to trim the top edge of the rubber with scissors to get it to fully close.) Secondly, there are two heaters for the defrost cycle, one that goes around the coils and another attached to a collector pan beneath the coils. When the cycle hits, those... Read more

First replaced defrost timer which tested OK - but reasonable price and easy to replace. When that did not fix the problem replaced the defrost thermostat and defrost heater. That fixed the problem. However all three parts tested OK ?? May have been a loose connection or intermittent problem with one of the parts. Final cost for all three parts was much cheaper than a service call!! Read more