Power Strike Small Engine Regular Starter Parts

Fix a broken or cracked dishwasher door handle with this direct replacement part. Basic hand tools needed. Remove 4-8 screws to install in 20-30 minutes.

Fix clicking sounds and warm temps with this start relay and overload protector. Controls compressor start-up and prevents overheating. 15-minute DIY fix.

Fridge won't cool and makes clicking sounds? The compressor overload may have failed. Protects against overheating. DIY repair takes 15-45 minutes.

This capacitor stores and releases electrical energy to support the appliance's circuit during startup and operation. Replacing a weakened capacitor can restore reliable performance and reduce humming, hard starting, or stalling in the affected component.

• Provides a power boost at startup and helps stabilize voltage during operation
• Helps the connected component start promptly and operate smoothly under load
• Common failure signs include humming, slow or no start, or intermittent operation
• Contribute to overheating or a tripped breaker/fuse when the component tries to start

• Disconnect power at the breaker or unplug the appliance. Before handling, safely discharge the old capacitor using a proper resistor-rated tool.
• Photograph or note wire positions; move each lead to the same-labeled terminal on the new capacitor and ensure snug connections.
• Mount the capacitor securely in its bracket; keep terminals covered and clear of metal surfaces.

This safety thermostat is a temperature-sensitive switch that helps protect your appliance from overheating. When excessive heat is detected, it opens the circuit to stop power to critical components, helping prevent damage and ensuring safe operation.

• Monitors temperature at a specific location and interrupts power if it exceeds a safe limit
• Can cause no power, no heat, or shutdown during use when failed or tripped
• Helps prevent overheating damage to internal components
• Restores normal operation when replaced

• Disconnect power to the appliance before service
• Note wire positions and terminal orientation before removal
• Use proper tools and avoid bending or stressing terminals
• After installation, check for underlying overheating causes (blocked airflow, failed fan, etc.)

This controller kit is the appliance's main electronic control. It reads inputs from the user interface and sensors to power and coordinate key components. Replacing a failed controller restores responsive controls and consistent, reliable operation.

• Interprets commands from the keypad and sensors to manage operation
• Controls relays powering motors, fans, compressor, or valves as designed
• Coordinates modes and cycle timing for proper performance
• Common symptoms: dead or blank display, unresponsive buttons, won't start, intermittent shutdowns, or error codes

• Disconnect power at the breaker or unplug the appliance before servicing
• Handle the board with ESD precautions; avoid touching connectors and components
• Photograph/label wire connections and transfer them one at a time to the new board
• After installation, verify any model-specific settings per the service documentation before testing

Fix a locked door error or F9 code with this oven door latch. Restores proper door locking and prevents interrupted cycles. Moderate DIY repair.

This kit includes a replacement heating element and a high limit thermostat for an electric dryer. The heating element generates the hot air that dries your clothes, while the high limit thermostat acts as a safety device to prevent overheating. Replace this kit if your dryer is not producing heat, takes too long to dry clothes, or shuts off prematurely due to overheating.

This temperature sensor mounts on the sealed-system gas inlet line in compatible refrigerators. It relays precise temperature feedback to the control so cooling and defrost cycles are managed correctly, helping maintain stable compartment temperatures. What it does:

• Senses temperature at the gas-inlet line; resistance changes are read by the control
• Helps regulate compressor, fan, and valve operation for proper cooling performance
• A failed sensor may cause erratic temperatures or extended run times
• Can correlate with control thermistor error codes or frost/ice patterns near the evaporator

• 1 thermistor sensor

• Disconnect power before servicing
• Note original sensor placement and insulation; reinstall in the same location and orientation
• Attach the sensor firmly to the line and route the harness as originally, away from sharp, hot, or moving parts
• Do not open or puncture sealed-system tubing; if damage is suspected, stop.

Refrigerator making clicking sounds and not cooling? This overload relay kit fixes compressor start problems. Easy DIY repair—pull off old relay and install.

Refrigerator clicking but not cooling? A failed compressor starter prevents reliable startup. This part restores proper cooling by helping the compressor start.

Microwave won't start or stops mid-cycle? A broken left door latch prevents proper door closure and engagement. Moderately difficult repair with panel removal.

Refrigerator not cooling or compressor won't start? This overload protector prevents motor damage from overheating. DIY-friendly fix in under 30 minutes.

Compressor won't start or kicks out after trying? This overload protector prevents motor damage. DIY-friendly repair, takes about 30 minutes to replace.

Fix a dryer door that pops open during the cycle with this door latch striker. Restores secure door engagement. Takes under 5 minutes to install.

This assembly includes the motor that drives the oven door latch mechanism and the switches that confirm whether the door is locked or unlocked during the self-clean cycle. It mounts behind the front panel of the range near the top of the oven cavity. Replace this part if the oven door won't lock for self-cleaning, won't unlock after the cycle completes, or if you receive an error code related to the door lock.