Circuit Board Parts

This washer timer controls the sequence and length of each cycle so the machine advances through wash, rinse, drain, and spin as selected. Replacing a worn timer restores reliable cycle progression and helps prevent stalls or incomplete loads.

• Directs power to the motor, pump, and inlet valves according to the selected program
• Advances the washer through fill, agitate, drain, and spin stages
• Common failure symptoms: cycle won't advance, stops mid-cycle, only runs on certain settings, or requires manually turning the knob to proceed
• Also presents as intermittent operation or erratic timing

• Disconnect power before servicing
• Access the control console; take clear photos and label wires, then transfer them to the new timer one at a time
• Seat the timer shaft through the panel and secure the mounting screws
• Reuse your existing control knob and dial; test a full cycle for proper advancement

The Washer Timer controls the sequence and duration of wash, rinse, and spin cycles. Replacing a worn timer restores proper cycle progression so the washer starts, advances, and completes loads reliably without manual knob turning.

• Sends power to water inlet valves, drive motor, and drain pump at the correct times
• Advances the wash, rinse, and spin stages in order
• Failure symptoms include: won't start, won't advance or stops mid-cycle, runs only on one setting, or no agitate/spin
• Helps restore accurate cycle timing and completion

• Disconnect power before servicing
• Open the console/control panel to access the timer; remove mounting screws/clips
• Label or photograph wire locations and transfer wires to the new timer one at a time
• Reuse the existing knob and dial as needed; seat the shaft fully and test a short cycle

This mechanical timer is the cycle control for select top-load washers. It sequences power to the motor, drain pump, and inlet valve so the machine advances through fill, wash, rinse, drain, and spin as designed.

• Controls the timing and order of each wash cycle step
• Sends power to components at the correct times
• Advances the cycle via an internal cam and timer motor
• Common symptoms: won't start or won't advance, stops mid-cycle, runs too long, or the timer knob doesn't move

• Disconnect power before servicing
• Access the control console; remove the dial/knob and mounting screws to release the timer
• Photograph wiring and transfer leads one-for-one to the new timer
• Reinstall, reassemble the console, and test operation

This electronic control board is the appliance's main controller. It interprets keypad/sensor inputs and energizes the correct loads so cycles start, run, and finish as selected—restoring reliable operation when the original board fails.

• Coordinates cycle timing and selected options
• Processes signals from user interface controls and sensors
• Switches power to motors, pumps, valves, heaters, or fans via onboard relays
• Typical failure symptoms: no display or response, won't start, cycle won't advance, or recurring error codes

• Disconnect power at the breaker or unplug before servicing
• Use ESD protection and handle the board by its edges
• Document and transfer connectors one-by-one; reuse any mounting hardware as needed
• Follow the service manual for any model-specific programming/calibration or diagnostics after installation

This replacement part is a control board that has been manufactured by Whirlpool and is compatible with refrigerators. The control board is important for proper appliance functionality, as it regulates and manages refrigerator functions, including the defrost times and the cooling. If the control board is broken, the refrigerator may experience a number of issues, including an inability to maintain cold temperatures or properly regulate defrost cycles. Ensure that perishable foods are stored safely and then unplug the appliance before attempting any repairs.This is a genuine OEM part that has been sourced directly from the manufacturer. It is compatible with refrigerators manufactured by Whirlpool, Maytag, Kitchenaid, Jenn-Air, Magic Chef, and some other brands. This part is sold individually.

This electronic control board is the main "brain" that directs your laundry appliance's cycles and powers key components. Replace a failed board to restore responsive controls, accurate cycle timing, and dependable operation. What it does:

• Coordinates cycle selection, timing, and status/display functions
• Interprets inputs from door/lock switches and sensors
• Switches power to loads such as the motor, heater, valves, or pump
• Common symptoms: blank/unresponsive controls, won't start, cycle won't advance, intermittent operation, or error codes

• 1 electronic control board

• Disconnect power before service; allow components to discharge
• Use ESD precautions; handle the board by its edges
• Photograph/label connections; transfer any brackets, spacers, or jumpers from the original board
• Seat connectors fully and run a test/diagnostic cycle after installation

This electronic control board is the appliance's brain, coordinating timing and power to run each cycle. When it fails, the unit may be unresponsive or behave erratically; replacing it restores reliable operation.

• Manages cycle timing and sends power to motors, valves, heaters, and other loads
• Interprets inputs from the user interface and sensors to execute selected settings
• Common symptoms: dead or unresponsive controls, won't start, or cycles that stop early or fail to advance
• Intermittent operation, erratic/blinking indicators, or visible burn damage on the board may indicate a failed control

• Disconnect power to the appliance before servicing.
• Use ESD protection; handle the board by its edges.
• Note/photograph wire locations and transfer connectors one at a time; mount the board securely in the original housing.
• After reassembly, restore power and run a test cycle or diagnostics per the tech sheet to confirm operation.

This refrigerator switch board provides the electrical switching and terminal connection interface for a control circuit. Replacing a worn board restores reliable activation of the related function and helps eliminate intermittent response from fatigued contacts or heat-damaged terminals.

• Houses the switch contacts and connection terminals on a compact PCB
• Converts actuator movement into a clean electrical on/off signal
• Routes power/signal to the appropriate component within the circuit
• Common symptoms: unresponsive or intermittent operation, needing extra force to activate, stuck on/off behavior, or visibly burnt/loose terminals
• Match the "terminal beta" variant to your original to ensure connector compatibility

• Disconnect power before servicing; use proper ESD precautions and handle the board by its edges
• Photograph and label all wire locations; move connections one at a time to the new board
• Transfer any brackets, levers, or screws from the original assembly as required
• Do not overtighten mounting screws to avoid PCB damage

This electronic main control board manages key refrigerator operations, coordinating cooling, defrost, and other functions so the appliance runs correctly.

• Regulates compressor and fans to maintain set temperatures
• Controls automatic defrost cycle
• Can resolve issues like no cool, warm freezer/fresh food, or intermittent operation
• May restore unresponsive controls or error/fault behavior

• Disconnect power before servicing; sensitive electronics—use ESD protection
• Photograph/label wire connections to ensure correct reassembly
• Handle by edges; avoid touching components and solder points
• After installation, restore power and allow normal cool-down period

This electronic oven control board manages the oven's heating, keypad inputs, and display. Replacing a failed controller can restore responsive controls, accurate temperature regulation, and normal oven operation.

• Controls bake and broil heating through the oven's relays
• Interprets keypad inputs to start/stop modes, timers, and settings
• Drives the display for time, temperature, and status; may post fault codes
• Coordinates preheat, timed cook, and self-clean on applicable models
• Failure symptoms may include a blank or erratic display, unresponsive buttons, oven not heating or starting, inaccurate temperature, or beeping/error codes

• Disconnect power at the breaker or unplug the appliance before servicing
• Access the board behind the control panel/backguard on most models
• Move wire connectors one at a time from the old board to the new; take photos for reference
• Handle the board carefully and avoid static discharge to protect sensitive components

Electronic clock/timer control that mounts behind the control panel. It provides the time display and manages oven functions so you can set temperatures, modes, and the kitchen timer reliably from the keypad.

• Provides clock and kitchen timer display; accepts keypad inputs for bake, broil, and temperature settings
• Controls oven heating functions by commanding the appliance per selected mode and setpoint
• Common failure signs: blank or dim display, unresponsive buttons, error codes or repeated beeping
• Also result in the oven not starting or not heating even though the appliance has power

• Disconnect power at the breaker before servicing; this control carries line voltage
• Access is typically through the control panel area; photograph wire connections to aid reassembly
• Handle the board carefully and avoid static discharge; transfer any brackets or supports from the original
• After installation, restore power, set the clock, and verify all oven functions

This switch board is the printed circuit board that carries the momentary switches behind the user interface. Replacing it restores reliable input so selections register consistently when you press the control buttons.

• Provides the electrical switch inputs for the control panel
• Sends low-voltage signals to the main control when buttons are pressed
• Helps fix unresponsive, intermittent, or stuck button inputs
• Symptoms may include having to press very hard or at a specific angle to activate a function

• Unplug the appliance before servicing
• Access the board by removing the control panel/trim; transfer any brackets, screws, or spacers from the original
• Note connector orientation; take photos before unplugging wires
• Handle the board by the edges and protect from static discharge

This electronic main control board manages and distributes power to the appliance's key components. Replace a failed board to restore normal operation when the unit won't power up, won't start, or runs erratically.

• Regulates and routes incoming power to motors, fans, compressors, heaters, and valves based on signals from sensors and the user interface
• Coordinates cycle timing and system protections to help prevent component damage
• Logs or triggers fault indications when abnormal conditions are detected
• Common failure symptoms: no power, dead/unresponsive controls, intermittent shutdowns, or unpredictable operation

• Disconnect power at the breaker or unplug the appliance before servicing
• Handle the PCB by the edges and use ESD protection to avoid static damage
• Photograph wiring and move connectors one at a time to the new board
• Inspect connected loads (motors, heaters, compressor, valves) for shorts before restoring power

This electronic control board manages incoming power and coordinates your appliance's core functions. Replacing a failed board can restore proper operation, responsiveness, and reliable cycling.

• Distributes and regulates power to internal components through onboard relays and circuits
• Interprets inputs from the user interface and sensors to execute programmed functions
• Helps coordinate starting, running, and stopping of key systems
• Common signs of failure: no power, unresponsive controls or display, intermittent shutdowns, cycles that won't start or complete

• Disconnect power to the appliance before servicing to avoid electrical shock
• Use ESD protection; handle the PCB by the edges to prevent static damage
• Photograph or label connectors; transfer one plug at a time to the new board
• Secure the board, confirm all connectors are fully seated, then restore power to test

Restore reliable operation with this power control board assembly. It regulates and distributes incoming power to the appliance's circuits and components so the unit powers up consistently and runs as designed when the original board has failed.

• Regulates and stabilizes power delivered to control and load circuits
• Switches power to motors, heaters, fans, and other components via onboard relays
• Provides low-voltage supply for control electronics
• Typical failure symptoms: no power, unresponsive controls, intermittent shutdowns, repeated blown fuse, or visible board damage

• Disconnect power before servicing; capacitors can retain a charge—allow time to discharge and use proper precautions
• Handle the board by the edges and use ESD protection to avoid static damage
• Photograph wiring and move connectors one at a time to the new board to maintain orientation
• Inspect wiring, fuses, and downstream components for shorts before restoring power to protect the new board

The is is a dishwasher control board. This part is tasked with controlling all of the internal parts of the dishwasher. It regulates the wash cycle, drying cycle, and other parts of a typical washing cycle. This part has many internal components and can become damaged over time or through use. If the dishwasher does not run, starts a cycle but doesn't finish it, or otherwise has functioning issues, this could mean the control board should be replaced.Before starting, make sure the dishwasher is unplugged for safety reasons. Open the door and remove the screws from the inner panel. Separate the panels while disconnecting the wire harness from the control panel. Pull the outer door panel and control panel off the appliance. Install the new part and reconnect wires and ribbons before reassembling the dishwasher. Plug in the appliance and test it.This is a genuine OEM replacement part designed to be compatible with dishwashers by Kenmore and Whirlpool. The control board comes directly from the manufacturer and is sold as a single component.