Cold Pump Hose Parts

90-degree rubber elbow connecting drain hoses in your dishwasher. Replace if cracked, split, or leaking. Installs between pump and drain line.

Size: 7 foot long.

Replacement water tube for side-by-side refrigerators. Routes water between filter and valve. Replace if cracked, kinked, brittle, or leaking.

Size: 8 foot long. This external washer drain hose is needed when there is more distance between the washer and the drain. Note: comes with 1.5" diameter clamp but hose is 1.25" in diameter; therefore you may need to order the 1.25" diameter clamp separately: WP356138

This is the chute component that directs water from the fill tube into the ice maker mold inside the freezer compartment. It ensures water flows accurately into the ice tray without spilling into the surrounding freezer area. Replace this part if water is leaking around the ice maker, ice forms outside the mold, or the chute is cracked or blocked with ice buildup.

This is a drain hose extension designed for dual evaporator refrigerators. It connects to the existing defrost drain system to route condensate water to the drain pan. Replace this part if you notice water pooling inside the refrigerator, leaking onto the floor, or ice buildup in the freezer compartment due to a clogged or damaged drain line.

Pre-formed gas line that connects the inlet regulator to the burner manifold in gas ranges. Replace if damaged, cracked, or leaking to restore safe operation.

Routes wastewater from your dishwasher to the sink drain or disposal. Replace if your existing hose is cracked, leaking, kinked, or too short for installation.

Fix washer leaks and drainage issues with a new water pump. Common when water leaks during drain cycle or won't pump out. DIY-friendly replacement.

This inlet hose carries supply water into the washer during the fill cycle. Replacing a worn or leaking hose restores proper water flow and helps prevent leaks and fill errors that can leave clothes unwashed or floors wet.

• Channels incoming water from the inlet valve into the washer
• Maintains a sealed connection to prevent drips and leaks
• Replaces hoses that are cracked, swollen, kinked, or clogged with mineral deposits
• Common symptoms: water leaking during fill, reduced water flow or fill error codes, visible cracks/splits

• Disconnect power and turn off both water supply valves before servicing
• Keep towels or a container handy; residual water may spill when removing hoses
• Note hose routing; fully seat ends and secure with existing or new clamps as required
• Restore water and power, then run a quick fill to check all connections for leaks

Hose washer and plastic insert for inlet hose. To order separately: for washer use WPY013783, for strainer use WP22002960.

This is a flexible hose that connects the detergent or fabric softener dispenser to the wash tub, allowing dispensed products to flow into the drum during the wash cycle. If you notice detergent not dispensing properly, leaking near the dispenser area, or water pooling under the washer during the fill cycle, this hose may be cracked, clogged, or disconnected and needs replacement.

Fix weak spray or grinding noise during wash cycle. This circulation pump assembly recirculates water through spray arms. Moderate DIY repair, 20-30 minutes.

21-inch drain hose extension for washers. Extends existing drain hose when original is too short to reach standpipe. Includes clamp for secure fit.

The DRAIN PUMP is an OEM component specifically designed for GE washers. It is located near the base of the unit and functions to remove water from the wash tub at the end of cycles. The drain pump works vigorously to expel soiled water through the drain hose for hygienic cleaning.  

Symptoms of a bad drain pump include:

• Water remaining in the tub even after cycles have finished running  
• Drain hose that is not effectively carrying away water
• Strange gurgling or churning noises coming from below the unit
• Possible leakage from seals or connections near the drain area

Causes can include internal blockages from built-up debris, wearing of impeller seals or motor, or physical damage impairing pump functionality.

Replace yours today with this genuine OEM GE part for thorough water extraction and machine drainage after every load. This GE replacement part is compatible with Hotpoint, RCA, and select Kenmore models.

Dishwasher not draining or has standing water? This drain pump assembly removes wastewater from the tub. Average DIY repair time: 30-90 minutes.