Power Strike Small Engine Regular Starter Parts

Refrigerator clicking but not cooling? A failed overload protector can prevent compressor startup. This part interrupts power during overheating.

Fixes clicking noise from compressor and fridge not cooling. Includes relay, overload protector, and capacitor. Most DIYers complete in 20-30 minutes.

Refrigerator making clicking sounds and not cooling? This overload relay kit fixes compressor start problems. Easy DIY repair—pull off old relay and install.

Fix a dryer door that pops open during the cycle with this door latch striker. Restores secure door engagement. Takes under 5 minutes to install.

Dryer not heating or overheating? A faulty temperature control thermostat often causes inconsistent heat cycles. This part regulates dryer temperature.

This is a start switch intended for use with dryers. With time or because of damage caused by accident, the start switch may stop working correctly. If the start switch isn't working, then the dryer will not function properly, and a replacement part should be ordered. If the push to start switch doesn't respond, it could be damaged or broken. Replacing the push to start switch on a dryer is a simple process. Start by unplugging the machine. Remove the back panel and pull out the old push to start button. Put the new button in its place and reattach the rear panel. Wear gloves for protection. Restore power only after the complete reassembly is performed. This push-to-start button is a genuine OEM replacement part. It is sold as an individual unit. The part is sourced from the manufacturer and made of durable materials. The push-to-start button can be installed in various dryer models made by SpeedQueen and Alliance brands.

This adjustable buzzer kit replaces a failed or noisy mini buzzer to restore audible alerts for cycles, timers and notifications. Compact design lets the appliance signal you reliably when cycles finish or need attention. What it does:

• Produces audible tones for cycle end, timers and other appliance notifications
• Replaces buzzers that are silent, intermittent, weak or emitting erratic beeps
• Helps you hear and identify completed cycles and timed alerts
• Small, mountable unit that fits behind the control panel and connects to the control board

• One adjustable buzzer kit

• Disconnect power before servicing to avoid shock risk
• Access may require removing the control panel; keep fasteners organized for reassembly
• Disconnect the buzzer wiring harness or connector before removing the old unit; connect the new buzzer the same way
• Test buzzer function with power restored before fully reassembling

Refrigerator won't cool or compressor clicks but won't start? This PTC start relay powers the compressor's start winding. Common DIY fix, restores cooling.

Fix a cracked or broken door handle that's hard to open or close. This dishwasher door handle typically takes 10-15 minutes to replace.

This is the door strike pin that engages with the door latch to keep the dryer door securely closed during operation. It is mounted on the dryer cabinet and catches the door latch when the door is shut. Replace this part if the dryer door will not stay closed, pops open during a cycle, or if the strike is visibly worn or broken.

A small rubber bumper that cushions and protects appliance doors, drawers or panels to reduce noise and prevent hard contact. Replaces worn or missing bumpers to restore a snug, quiet close. What it does:

• Provides a soft buffer to stop doors or drawers from banging into the cabinet or frame
• Reduces vibration and rattling during operation
• Helps doors and panels sit properly when closed
• Simple, non-electrical part — no wiring or adjustment required

• One replacement bumper

• Inspect the mounting hole or surface; clean debris before installing
• Press the bumper into the hole or onto the surface until fully seated; use a blunt tool if needed for tight fits
• Disconnect power to the appliance first and follow OEM instructions
• Remove old adhesive before installing the new bumper

Dryer won't start when you press the button? This push-to-start switch closes the circuit to begin cycles. Easy DIY repair restores reliable starting.

Fix a dishwasher that won't start when the door is closed. This door latch assembly engages the closure mechanism so your unit recognizes the door is secure.

This door catch assembly secures the door closed so your machine can start and run without interruptions. A worn or broken catch can keep the door from latching, causing cycles not to begin or to stop mid-cycle.

• Latches the door to engage the door switch and allow operation
• Helps prevent door popping open during use
• Common failure signs: door won't stay closed, must hold door to run, cycle won't start due to open-door indication
• Restores proper door alignment and engagement with the strike

• Unplug the appliance before servicing
• Open the door and remove the fasteners securing the old catch
• Transfer the new catch in the same orientation; reuse existing screws if not supplied
• Test door closure and latch engagement before resuming use

This micro switch is a compact, snap-action electrical switch that sends an on/off signal when a lever, latch, or paddle is moved. Replacing a worn switch restores reliable detection and control response for the affected function.

• Converts mechanical movement into an electrical open/close signal to the control
• Commonly used for lever/paddle actuators, latches, or interlock detection within the appliance
• Safe symptom clues: no response when actuated, intermittent operation, or a function stuck on/off
• Physical clues: weak or absent "click" when pressed, heat discoloration or damage at terminals

• Disconnect power before servicing; if the product is connected to a water line, close the supply valve
• Note wire positions and terminal labels (COM/NO/NC); transfer wires one at a time to matching terminals
• Match the actuator orientation and mounting position to the original for proper operation
• After installation, verify continuity with a multimeter and test function before reassembly

A thin pad-style moisture sensor that detects wetness levels during the dry cycle and sends signals to the dryer control so the machine can adjust drying time. Replaces a worn or damaged sensor to restore reliable moisture-sensing performance. What it does:

• Detects residual moisture in the drum or on clothing and communicates readings to the control board
• Helps the dryer end cycles when items reach the set dryness level to prevent over-drying
• Common symptoms of a failing pad: long or incomplete drying cycles, clothes still damp at cycle end, or inconsistent auto-dry behavior
• Works as the sensing surface that partners with the dryer's sensing system to measure conductivity/moisture

• One sensor pad

• Disconnect power to the appliance before starting any repair
• Handle the sensor surface carefully; avoid touching conductive areas with bare hands or tools
• Install in the original mounting location and secure wiring connectors firmly; verify routing to avoid pinching