Power Strike Small Engine Regular Starter Parts

Fix a refrigerator that clicks but won't start or cycles on and off repeatedly. This compressor start relay powers the start winding for reliable cooling.

Fix an oven door that won't lock during self-clean or clean cycle errors. This door latch assembly secures the door and reports lock status to the control.

Refrigerator clicking but not cooling? A failed compressor start device causes repeated clicking and warm temps. Quick DIY fix restores reliable starts.

A thin pad-style moisture sensor that detects wetness levels during the dry cycle and sends signals to the dryer control so the machine can adjust drying time. Replaces a worn or damaged sensor to restore reliable moisture-sensing performance. What it does:

• Detects residual moisture in the drum or on clothing and communicates readings to the control board
• Helps the dryer end cycles when items reach the set dryness level to prevent over-drying
• Common symptoms of a failing pad: long or incomplete drying cycles, clothes still damp at cycle end, or inconsistent auto-dry behavior
• Works as the sensing surface that partners with the dryer's sensing system to measure conductivity/moisture

• One sensor pad

• Disconnect power to the appliance before starting any repair
• Handle the sensor surface carefully; avoid touching conductive areas with bare hands or tools
• Install in the original mounting location and secure wiring connectors firmly; verify routing to avoid pinching

This 250V, 1A fuse protects your washer's control circuit from overcurrent. Replacing it can restore control power once the root cause is corrected.

• Opens to protect electronics when current exceeds its 1A rating
• Check this part if the washer has no power, the control panel is dead, or it won't start
• A blown fuse will test open for continuity
• Repeated failure points to an underlying short or component fault that must be fixed

• Disconnect power before servicing
• Access the fuse at the control board or fuse holder
• Replace only with the same rating: 1A, 250V
• Inspect wiring/components and correct any short before restoring power

Color: Black. Instruction sheet included.

This is an electronic lock mechanism designed for the coin box on commercial-style washing machines. It secures the coin collection compartment to prevent unauthorized access. Replace this lock if the coin box no longer latches properly, the lock mechanism has failed electrically, or the key no longer engages the lock.

This door catch assembly secures the door closed so your machine can start and run without interruptions. A worn or broken catch can keep the door from latching, causing cycles not to begin or to stop mid-cycle.

• Latches the door to engage the door switch and allow operation
• Helps prevent door popping open during use
• Common failure signs: door won't stay closed, must hold door to run, cycle won't start due to open-door indication
• Restores proper door alignment and engagement with the strike

• Unplug the appliance before servicing
• Open the door and remove the fasteners securing the old catch
• Transfer the new catch in the same orientation; reuse existing screws if not supplied
• Test door closure and latch engagement before resuming use

Fix a refrigerator that won't start or hums but doesn't run with this compressor start capacitor. Restores reliable cooling when the compressor fails to start.

Fix a compressor that won't start, hums, or cycles on and off every few minutes. This motor start capacitor restores reliable compressor operation.

Refrigerator not cooling or won't start? A failed compressor start device prevents startup. DIY repair in under 30 minutes restores reliable cooling.

Fix a microwave door that won't close or latch properly with this replacement hook. Restores secure door closure and eliminates gaps or loose fit issues.

If your dishwasher door won't stay closed or pops open during cycles, the door strike may be broken. This latch component secures the door shut.

Door won't close or latch properly? This latch keeper secures the door strike so your dishwasher stays closed during cycles. Quick DIY repair.

These moisture sensor rods detect how damp the load is and signal the control, helping the dryer stop at the right time. Replacing worn or coated rods restores accurate Auto Dry performance and reduces damp loads or overdrying.

• Measures moisture by sensing conductivity across the rods as clothes tumble
• Sends feedback to the timer/control to adjust cycle length on Sensor/Auto Dry
• Safe symptom matches: cycles end too soon or run too long, clothes remain damp, Auto Dry doesn't advance reliably
• Residue from dryer sheets/fabric softener can insulate the rods and affect readings

• Disconnect power (and shut off gas supply for gas models) before servicing
• Access the rods at the front bulkhead/lint filter housing; panel removal may be required on some models
• Remove mounting fasteners, transfer wiring in the same orientation, and secure the new rods
• Ensure the sensing surfaces are clean and unobstructed; test on an Auto Dry cycle

Fixes burner that won't heat or stays on one temperature. This infinite switch restores variable heat control to your cooktop surface element.