Power Small Engine Start Switch Parts

Fixes dryer not heating or overheating issues. This safety thermostat monitors temperature and cuts power when too hot. Basic DIY repair, 30 minutes.

Dryer won't heat or start? A failed thermostat breaks the heating circuit. Common DIY fix—test for continuity with a multimeter. Typical repair time: 30-60 minutes.

Fix clicking sounds and warm temps with this start relay and overload protector. Controls compressor start-up and prevents overheating. 15-minute DIY fix.

Fridge won't cool and makes clicking sounds? The compressor overload may have failed. Protects against overheating. DIY repair takes 15-45 minutes.

Dryer overheating or taking too long to dry? This control thermostat regulates internal temperature by cycling the heater on and off. Easy replacement.

Fix a dryer that won't heat, overheats, or runs too long. This thermostat cycles the heating element to maintain safe drying temperatures.

Fix a dryer that overheats or won't heat properly with a new temperature switch. Controls heat settings across multiple cycles. DIY-friendly repair.

Wax motor for detergent/rinse-aid dispenser.

Dryer not heating or overheating? This high-limit thermostat cuts power when temperatures exceed safe levels. Common fix for no heat issues.

This wiring harness routes power and control signals between key components inside your range or wall oven. Replace a damaged harness to restore safe, reliable operation and prevent intermittent heat, shorts, or non-working burners and oven functions.

• Distributes electrical power and signals between controls, switches, heating elements/igniters, and safety components
• Maintains correct connector orientation and wire routing for dependable operation
• Typical symptoms: no heat in oven or on surface burners, intermittent operation, breaker tripping, or visible burnt/melted wiring
• Restores stable connections to reduce arcing and overheating

• Disconnect power at the circuit breaker; for gas ranges, also shut off the gas supply
• Label or photograph all connections and transfer one wire at a time to avoid miswiring
• Route the harness exactly as original; keep away from sharp edges and hot surfaces; secure with existing clips/ties
• If connectors don't match or any terminals are heat-damaged, stop and inspect mating components.

Interior light stays on or won't turn on? This upright freezer door switch controls lighting when the door opens and closes. Simple fix for most DIYers.

This replacement moisture sensor bar mounts inside the drum and helps the dryer detect when laundry is dry. A worn or damaged bar can cause sensor-dry cycles to end too soon or run too long.

• Senses moisture on fabrics and signals the control to advance or extend auto-dry cycles
• Helps stop the cycle when clothes reach the selected dryness level
• Symptoms can include auto-dry cycles ending early, extended run times, or inconsistent dryness
• Build-up on the bars can also affect sensing performance

• Disconnect power before servicing; shut off gas supply for gas dryers
• Access the sensor at the front bulkhead/lint housing; move wire leads to the new bar and secure with existing hardware
• Clean any residue from both sensor bars to improve accuracy
• Reassemble and test with a small damp load on a sensor cycle

Dryer overheating or shutting down unexpectedly? The high-limit thermostat monitors temperature and cuts power to prevent damage. DIY repair in 30 minutes.

This blower speed switch lets you select the blower/fan speed to restore proper airflow control in your appliance. It replaces a worn or faulty speed selector so the blower will respond correctly when you change settings. What it does:

• Controls the blower/fan speed so the appliance can run at selectable airflow levels
• Replaces a switch that is stuck, unresponsive, or only running at one speed
• Restores reliable electrical connection between the control circuit and blower motor
• Helps eliminate intermittent fan operation or loss of speed selection

• Disconnect power to the appliance before starting any repair.
• Verify wiring placement and retain original fasteners; wiring diagram for correct connections.
• Handle terminals carefully to avoid bending or damaging contacts.

This time-delay fuse protects the appliance's power circuit by opening when current exceeds a safe level while tolerating brief inrush current. Replacing a blown fuse can help restore power once the root cause is corrected. What it does:

• Protects the line and control circuits from shorts and overloads
• Time-delay design helps prevent nuisance opening during startup surges
• When open, the unit will be completely dead—no display, lights, or response
• Repeatedly opening usually indicates an unresolved electrical fault that needs diagnosis

• 1 time-delay fuse

• Disconnect power at the breaker before servicing; some appliances can retain dangerous high voltage
• Replace only with the same type and rating specified by the manufacturer
• Inspect the fuse holder and wiring for heat damage or loose connections before reassembly
• If the new fuse opens immediately, stop and diagnose the underlying cause; never bypass or upsize a fuse

This capacitor stores and releases electrical energy to support the appliance's circuit during startup and operation. Replacing a weakened capacitor can restore reliable performance and reduce humming, hard starting, or stalling in the affected component.

• Provides a power boost at startup and helps stabilize voltage during operation
• Helps the connected component start promptly and operate smoothly under load
• Common failure signs include humming, slow or no start, or intermittent operation
• Contribute to overheating or a tripped breaker/fuse when the component tries to start

• Disconnect power at the breaker or unplug the appliance. Before handling, safely discharge the old capacitor using a proper resistor-rated tool.
• Photograph or note wire positions; move each lead to the same-labeled terminal on the new capacitor and ensure snug connections.
• Mount the capacitor securely in its bracket; keep terminals covered and clear of metal surfaces.