Pipe Parts

The Dispenser to Tub Hose is an OEM part for Frigidaire washing machines. This hose is responsible for transporting detergent and other cleaning agents from the dispenser to the tub during the wash cycle.  

Common causes of a bad hose include constant exposure to water and detergent, which can lead to wear and tear, blockages from detergent buildup, or physical damage such as cracks and splits.

Symptoms of a bad dispenser to tub hose include:

• Water leaks near the detergent dispenser
• Uneven or insufficient distribution of detergent
• Visible cracks, splits, or other damage to the hose
• Error codes on the washing machine related to water flow

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

Size: 5 foot long. Rubber fill hose used on most automatic washing machines. Two hoses used per machine.

This inlet hose routes incoming water from the washer's fill valve into the machine to support proper filling. Replace a cracked or leaking hose to stop drips, prevent water damage, and restore reliable fill performance.

• Directs incoming water from the fill valve to the dispenser/tub during wash cycles
• Maintains a sealed path to prevent internal or external leaks
• Helps the washer reach proper fill levels and timing
• Common symptoms of failure: water on the floor, leaks during fill, visible cracks or bulges, long/no fill or IE error

• Unplug the washer and turn off both hot and cold water supplies
• Keep towels or a pan handy; relieve residual water pressure before disconnecting
• Note the original routing; fully seat the hose on fittings and secure with existing clamps
• Restore water and power, then run a quick fill to check for leaks

This drain hose assembly carries wastewater from the washer to the household standpipe or laundry tub. Replacing a cracked, kinked, or leaking hose helps restore proper draining and reduces the risk of water on the floor. What it does

• Routes drain water from the pump to the standpipe or laundry tub
• Helps maintain proper flow during drain/spin cycles
• Addresses leaks behind or under the washer caused by a damaged or loose hose
• Can help resolve slow or incomplete draining due to kinks, splits, or blockages

• Includes 1 drain hose assembly

• Unplug the washer and turn off water supply; have towels or a pan ready for residual water
• Move the appliance for access; note original hose routing and connection points
• Transfer and securely tighten any existing clamps/connectors; push hose fully onto fittings
• Route without sharp bends; secure outlet in the standpipe or sink and test for leaks

The Hose is an OEM part for Whirlpool washing machines. This hose is responsible for transporting water from the washer tub to the drain pump and then out to the external drain during the drain cycle. 

Causes of a bad drain hose can include regular wear and tear, blockages from debris, or cracking and splitting due to age and repeated use. 

Symptoms of a bad hose include:

• Water leaking from the washing machine during or after a cycle
• Slow or incomplete draining of water
• Visible cracks, splits, or other damage on the hose
• The washing machine stopping mid-cycle due to drainage problems

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The Refrigerator Drain Connector is an OEM part for Whirlpool refrigerators. It is responsible for directing water and condensation from the evaporator fan coil and defrost into the drain pan. 

Causes of a bad drain connector can include cracks, breaks or deformations caused by repeated thermal cycling or impact damage. Mineral or lime buildup inside the connector over many years can also restrict water flow.

Symptoms of a bad drain connector include:

• Water or condensation leaks around the connector area 
• Puddles or watermarks on the floor behind the fridge
• Slow drainage of water from the evaporator fan coil
• Mold or mildew growth near the connector or drain area

This replacement part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This outer drain hose routes wastewater from your washer to the household standpipe or sink. Replacing a cracked, kinked, or clogged hose restores proper draining and helps reduce leaks at the back of the appliance.

• Carries discharge water from the drain pump outlet to the home drain connection
• Damage such as splits, pinholes, or hardening can cause leaks during the drain cycle
• Kinks or blockages can lead to slow or no draining and water left in the tub
• Visible wear, brittleness, or recurring drain errors are common signs the hose needs replacement

• Disconnect power and turn off water supply before servicing
• Pull the washer forward to access; keep towels or a pan ready for residual water
• Detach the old hose from the pump/outlet and household drain; transfer and reuse clamps or brackets as required by your model
• Route the new hose without kinks, secure all connections, follow your model's manual for drain placement, then run a test drain and check for leaks

The Sump Hose is an OEM part for Frigidaire washing machines. This hose carries water from the tub to the pump, ensuring proper drainage during the wash and spin cycles.  

Causes of a bad sump hose can include regular wear and tear, cracks or holes from aging, and clogs from debris buildup. 

Symptoms of a bad sump hose include:

• Water leaking from the bottom of the washing machine
• Slow or incomplete drainage
• Visible cracks or holes in the hose
• The washing machine stopping mid-cycle due to drainage issues

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This standpipe adapter connects the washer's drain hose to a household standpipe for a secure, stable fit. It helps ensure proper drainage and reduce leaks or hose movement during operation when installing or refreshing the drain connection.

• Adapts the washer's drain hose for standpipe installations
• Helps keep the hose seated to minimize leaks, kinks, or pull-outs
• Supports a proper air gap to reduce siphoning when installed correctly
• Common symptoms: water at the standpipe, hose popping out, drain-back after a cycle, or improper draining

• Disconnect power and turn off water before working behind the unit.
• Place a towel to catch residual water from the drain hose.
• Slide the adapter onto the hose end, insert into the standpipe, and secure per the manufacturer's instructions.
• Ensure the hose isn't kinked and test a drain/spin cycle to check for leaks.

This replacement exhaust hose vents hot discharge air from a portable air conditioner through the window kit, restoring proper airflow and cooling performance when the original hose is cracked, collapsed, leaking, or missing.

• Directs hot air from the unit to the outdoors via the window panel
• Helps maintain correct airflow and cooling efficiency
• Replaces a damaged, brittle, or collapsed vent hose
• Symptoms may include poor cooling, warm air leaking into the room, or the hose detaching

• Unplug the unit and allow it to cool before service
• Remove the old hose from the rear outlet and window panel couplers
• Seat and lock the new hose fully onto each coupler per your model's design
• Route the hose as short and straight as possible; avoid kinks or sharp bends for best airflow

This replacement hose routes liquid or air between internal components, maintaining a secure, leak-resistant path. Replace a brittle, cracked, or clogged hose to prevent leaks and restore proper flow and sensing performance.

• Provides a sealed pathway between components such as the pump, tub, valve, drain path, or pressure system
• Helps maintain correct water flow or pressure/level sensing
• Common symptoms: leaks, kinks/cracks, standing water, slow/failed drain or fill, related error codes
• Restores reliable connections when used with properly seated clamps

• Disconnect power and shut off water supply before servicing; allow hot parts to cool
• Place towels or a shallow pan to catch residual water
• Note routing and clamp locations; transfer or replace clamps as needed and seat the hose fully on fittings
• Test for leaks with a short cycle and re-check all connections

This drain inlet hose carries wastewater through the washer's internal drain path during drain and spin cycles. Replacing a cracked, kinked, or leaking hose helps restore proper draining and protect floors and nearby components from water damage. What it does:

• Routes drain water between internal components to the drain outlet
• Maintains a sealed flow path to help prevent leaks
• Common symptoms: water on the floor during/after draining, standing water left in the tub, visible cracks/bulges/kinks on the hose
• May clog with debris, restricting flow and causing slow or no drain

• 1 drain inlet hose

• Unplug the washer and shut off water supply before servicing
• Have towels or a shallow pan ready; residual water may spill when hoses are removed
• Note hose routing and clamp positions; ensure the new hose is fully seated and not twisted or kinked
• After installation, run a quick drain/spin and check all connections for leaks

This tub-to-pump hose connects the washer's outer tub to the drain pump, channeling water out during the drain cycle. Replacing a worn hose helps stop leaks and restore consistent draining when the original is cracked or deteriorated.

• Provides a sealed path from the outer tub to the drain pump during draining
• Helps the washer remove water at the end of wash and rinse cycles
• Common failure symptoms: water leaking at the front/bottom, puddles after a cycle, or slow/no drain
• Visual clues: cracks, splits, swelling, or soft spots in the hose rubber

• Unplug the washer and turn off water supply; expect residual water—use a pan/towels
• Access the hose per your model (often behind the lower front/service panel); note routing/orientation before removal
• Transfer and reuse the existing clamps; seat the hose fully on both fittings and secure evenly
• After reassembly, run a brief fill/drain test while watching for leaks

This drain hose carries wastewater from the washer's drain pump to your home standpipe or sink, ensuring proper draining and helping prevent leaks or backflow. Replace a cracked, kinked, or clogged hose to restore reliable draining.

• Provides a sealed path for wastewater from the drain pump to the household drain
• A damaged or clogged hose can cause leaks, slow draining, or drain-related error codes
• Kinks, splits, or pinholes may allow water to escape during drain cycles
• Loose or worn hose ends can lead to drips at the pump or rear connection

• Disconnect power and water supply; pull the appliance forward to access the hose
• Expect residual water—use towels or a shallow pan and clamp off the old hose if needed
• Note hose routing and clamp locations; reuse existing clamps and secure connections firmly
• Route the new hose without kinks and set the discharge height per your installation guide to prevent siphoning

This drain hose extension kit increases the reach of your appliance's drain line so it can connect to a farther standpipe or sink, supporting proper drainage and reducing stress on fittings that can lead to leaks. What it does:

• Extends the existing drain hose to accommodate installations where the drain connection is farther away
• Helps maintain a secure, leak-resistant connection when routed correctly
• Useful when relocating the appliance, changing cabinetry, or updating plumbing
• Common signs you may need it: hose won't reach, kinks when stretched, or occasional water near the drain line

• One drain hose extension kit

• Disconnect power and shut off the water supply; have a towel or pan ready for residual water
• Join the extension to the existing drain hose with the proper coupling/clamps; tighten securely and avoid kinks or sharp bends
• Route and support the drain line per your model's installation guide and observe any maximum total hose length
• Run a short test cycle and check all joints for leaks

Size: 90 inches long. To order hose extension use 12001585. To order siphon break use 76660.