Coil Parts

I ordered the 8 inch Haliant Element from Appliance Parts Pro with overnight shipping (I needed to have it working for Easter weekend!) and it arrived when promised and in perfect condition! To replace, you need a couple of boards longer than the stove is wide to hold the stove above the counter. You will also need a T15 Torx head on a handle or socket wrench. It also helps to have some pliers, and a second person to slip the boards under and out from the stove when you lift it. First, shut... Read more

Replaced defrost heater, temperature and defrost limiter thermostat. After taking the cover off the air chiller I found the coils frozen solid and defrosted it with a hair dryer. Once defrosted I remover the heater coil to test it it was fine, then I could see the defrost limiter was broken and as I put the unit back together I broke the heater tube (it is glass) so I ordered all the parts that might be defective and replaced them for less than the charge of having some one come to check it out. Read more

Ordered conversion kit from Appliance Parts Pros.com and installed it myself. Most difficult part of the repair, was the removal of the front casing of the dryer to access the location of venturi tube to be changed out. The instructions were helpful, but not specific enough for my dryer. Once the casing was off, the job was not too difficult - you will need a set of short screwdrivers to remove the burner flange and close the pressure adjustment screw, normal length screw drivers will come into... Read more

• Little to no heat when broiling
• Element will not heat
• Little to no heat when baking

I ordered the bake unit from appliancepartspro.com; while ordering, I decided to go ahead and replace the oven broiler burner as well. Appliancepartspros.com's videos helped me replace the parts with ease. It took barely 30 minutes to install both. Plus, very fast shipping and correct parts. Now, I do not have to worry about baking during Thanksgiving! Cheers, Sean Read more

• Little to no heat when baking

Repair video was very helpful. Followed the instructions and the element was replaced easily and correctly. Read more

Raised ceramic top, removed old element, installed the new one. Read more

1) ordered new boiler element after searching for oven/stove model # online 2) unplugged oven 3) removed 2 screws holding element in place 4) pulled out the element and a length of wires attached to the element (enough that the wires wouldn't pull back into the hole after detached) 5) used needle-nosed pliers to detach wire clamps, noting which wire attached to which side of the old element 6) removed old element and its pieces from the bottom of oven 7) attached wires to new element,... Read more

I purchased a new elelmnt and fixed it myself!! Read more

Ordered the parts from ApplianceParts Pros.com and saved the $100 service call. The fix was easy, complete instructions enclosed. Read more

First, I took an ohm reading across the elements and determined the bad one, which was failed, open circuit. (Zero continuity) I then replaced the lower heating element of the upper oven. Although the design of the oven and element make it appear that it will just drop down and slide out the front, this is not quite the case. There is not enough clearance for it to drop all the way down. You have to pull the entire double-oven unit out of the wall, separate the upper and lower halves a few... Read more

Tried to put refrigerator in defrost mode and defrost would not initiate. Checked the bi-metal and heater, both tested good. Replaced the ADC board and refrigerator went in to defrost. problem solved. Read more

• Element will not heat
• Won't start

Turned off power supply. Removed two screws (near the oven door) holding the ceramic top. Slid the top forward, disengaged the two power supply cables, and removed one ground wire. Removed range top, and put on a flat surface. Unclamped two power supply wires, one ground wire and one thermocouple wire from the element. Unscrewed the bracket from the element, and remove the element from the range top. Remove the two clamps from the old element, and put them on the new element at the same... Read more

REPLACED DEFROSTER, CONDENSER FAN MOTOR AND DEFROST THERMOSTAT. Read more

It took less then 15 min. Read more

• Won't start
• No heat

Unplugged range, removed back panel. Loosened plug block from range, unhooked wires from existing element, then sliced through insulation between element ends with sharp knife. Removed screws holding element ends then removed element. Inserted new element, screwed it in place, connected wires and replaced plug block. Vacuumed up fiberglass insulation dust and replaced back panel. Replaced plug then tested. Read more

REPLACED THE ELEMENT. Read more