Power Strike Small Engine Start Switch Parts

Checked and cleaned vent which was in need of cleaning, but not too bad (I do not consider this a primary causal detail, but can be a problem, so clean yours). Replaced Hi-Limit Thermostat (safety thermostat) after confirming the circuit was open with ohm meter. While I was in there, I completely cleaned the heater and ducting and internal workings of the dryer. Confirmed the heater coils were good via 20ohm, 20ohm, 40ohm readings (LG service manual has wrong readings). Two weeks later, same... Read more

I first diagnosed the problem by replacing the burner control (Infinite switch) with one from a smaller burner (one that I knew worked fine). That seemed to solve the problem. I ordered the correct control for the big burner on Saturday night, it arrived Tuesday and installed it in less than 10 minutes using only a Phillips screwdriver. Remember to unplug the stove before performing any service. Take this time to clean around and under the stove. (You know it needs it!) Read more

Purchased, Igniter Kit, Gas Valve Coil Kit, and as a precaution Thermal Fuse and Cutoff-Tml. Was pretty confident the problem was the gas valve coil, but figured that why not just replace the other items while I had the unit apart. Researching and utilizing this site certainly helped me out in figuring what the problem may be. Watched the instruction videos which were very detailed and helpful. The replacement and repair was not that difficult and the work was done rather quickly. Doing... Read more

• Light not working
• Not dispensing water
• Ice maker not making ice

I watched the repair video and I replaced the switch. I ordered the switch on Friday and the part came the next day. Amazing. Read more

Replaced heating element and thermostat, took me about 2 hours but that's because i had to vacuum out the dryer inside and I also checked the fan before I closed the dryer back up. I have a Samsung DV448AAEP. Works great and saved my family money! Read more

• Won't start

Removed and replaced 3 door switches and mounting bar that holds switches plastic gets brittle with age and each switch comes out slightly different from each other, the chances of breaking a mounting pin is very easy. care should be taken when snapping mounting bar back into place to insure top latch and bottom latch locate properly insure bar is proper aligned when tightening screws their is free play in mounting bracket that could affect door properly engaging switches. NOTE that their are... Read more

• No heat or not enough heat

Replaced the inlet control thermis (thermostat) . Now it completes the cycle but clothes are not 100 % dry. I would add 15 minutes more and that helps. FYI: you don't need to remove the drum, just remove the top cover and that will give you enough space to replace the sensor Thank you Appliance Parts for your fast speed of delivery. Read more

Replaced the Thermal Fuse on the dryer. Read more

Yes Read more

Replaced the starter and capacitor, 30minutes, $60.... Bam!!! Fixed Read more

• Door won't close

I found the door switch was not making contact when the door closed. I adjusted it, but then it would not open so the dishwasher would run when the door wasn't closed. The contacts were too long in the switch so they would bend and stay together when the door opened. The original switch was very poorly made for a very expensive Maytag dishwasher. The new switch you supplied was much better quality and easily replaced the one that was installed at the factory. I was a little baffled at the... Read more

• Not dispensing water

I watched the Appliance Parts Pros repair video and decided to remove the front panel to diagnose the problem. While the repair video is excellent, I could not remove the ice/water dispenser front panel with a putty knife. On my model, 106.56234400, there is no clip that can be released by sliding a putty knife up under the front panel. It took a little effort but I was able to pop the left lower corner clip just by pulling it out with my fingers. Once the cover was off I could see that the... Read more

• Doesn't shut off

Background: Roper Electric Dryer model REX6634RQ0 purchased new in early 2006 by my wife. Dryer use profile is low to moderate as it was used by only one person (working from home) from 2006 to late 2007 then moved and stored in a dry basement until mid 2009. Moved and used by primarily just two people (plus occasional children visits) from mid-2009 thru late 2011 with three moves involved with in that time. Then stored in a dry shipping container until moved again in 2013. The multiple... Read more

• Won't start

Looked at the diagnostic help on Appliance Parts Pros.com and the start switch was the problem, but only 25% of the time, so I was a little concerned it may be a different problem. The switch was reasonably priced, so I ordered it and it arrived in two days! It was very easy to follow the repair video, however, my GE Gas dryer had a lot of screws rather than 2 screws and tabs on the model in the video, so it took a little more time to open up. After turning off the gas and unplugging the... Read more

• Too hot
• No heat or not enough heat
• Takes too long to dry

Replaced thermal stats Read more

• Won't start
• Lid or door will not open
• Lid or door won't close
• Will not agitate

The washing machine would allow you to program it, and all the lights on the control panel would light up, but pressing start did nothing. I tried putting the washer in diagnostic mode, but was unable to do so. The machine was not showing any fault code. I originally thought it was a problem with the 'Start' button and I thought that I'd buy a replacement part from the original seller of the washer. I was told by the 'live help chat person' that the problem was likely in the washer user... Read more