J Ptc Parts

Dryer won't start or run? A faulty belt switch often causes this when the belt snaps or slips. This switch monitors belt tension and is a fairly easy fix.

If your washer overfills, underfills, or won't advance cycles, the water level pressure switch may have failed. Takes about 10-15 minutes to replace.

4-wire power cord connects your electric dryer to a 4-prong household outlet. Replace a worn, damaged, or overheated cord to restore safe power connection.

This replacement switch restores reliable on/off signaling to the circuit it controls, helping your appliance start, stop, and respond correctly. A worn switch can cause intermittent operation, no response, or lights and functions that don't activate. What it does:

• Provides an electrical open/closed signal to enable functions like starting a cycle, powering a motor or light, or shutting a feature off
• Acts as a safety/position interlock (such as door, lid, float, or hood) depending on the model
• Typical symptoms include won't start, won't stop, light won't turn on/off, or intermittent operation
• Can be checked with a multimeter for continuity when actuated

• 1 switch

• Disconnect power before servicing; turn off gas or water supply if applicable
• Access the switch, note wire locations, and transfer leads one at a time to the new switch
• Mount securely, ensure the actuator aligns and wires aren't pinched
• Reassemble and test operation before finalizing

This is the washer's water level switch that senses tub level via air pressure and provides five selectable fill settings. Replacing a failed switch restores accurate filling and lets the cycle advance properly through wash, rinse, and spin.

• Monitors air pressure from the tub to detect actual water level
• Controls the inlet valves to start/stop filling at the selected setting
• Signals the timer/control to begin agitation and advance the cycle once full
• Common symptoms: overfilling or water keeps running, stops filling too soon or won't fill, inconsistent water levels, cycle won't advance due to incorrect level detection

• Disconnect power and turn off water supply before servicing
• Access the control console; remove the selector knob/dial and panel as needed
• Note wire locations (take a photo), move the harness, and transfer the pressure hose; ensure the hose is clear and firmly seated
• Securely mount the new switch, reassemble the console/knob, restore utilities, and test each fill level

Fix compressor clicking every few minutes or fridge not cooling. This start relay and overload combo helps your compressor start and prevents overheating. Easy 5-minute fix.

The Switch is an OEM component specifically designed for Frigidaire washing machines. It controls various cycle options like water temperature levels, spin speeds, and additional settings like stain removal cycles.

Causes of a bad switch can include water or chemical damage leading to component failure over time, or loose wiring connections causing intermittent issues.  

Symptoms of a bad switch include: 

• Inability to select wash cycles or adjust settings  
• Unresponsive or inaccurate temperature levels
• Lights/displays not functioning as normal
• Error codes indicating switch problems

This OEM Frigidaire replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models. Replace yours today to avoid expensive repairs down the road.
 

Fix a washer that won't fill with water or overfills with this water level pressure switch. Controls proper water amounts for each wash cycle.

Fix a humming compressor that won't start by replacing this capacitor. Restores proper startup and cooling. DIY-friendly repair under 30 minutes.

Dryer won't heat or overheats on low settings? A faulty temperature selector switch prevents proper heat control. Easy DIY fix in 10-15 minutes.

Supplies electrical power from wall outlet to refrigerator. Replace this cord if cut, frayed, overheated, or damaged to restore safe electrical connection.

This fixed-value resistor is an electrical component used in select dryers to limit current in a specific control circuit. It helps the timer or electronic control operate correctly by dropping voltage to safe, design-intended levels.

• Provides precise resistance to reduce voltage/current in the designated dryer circuit
• Supports proper operation of the timer, control board, or end-of-cycle signal (varies by model)
• Failure may present as a timer that won't advance, an inoperative signal/buzzer, or irregular cycle behavior
• Replace if visibly burned/damaged or if testing shows an open or shorted condition

• Disconnect power to the appliance before servicing
• Access the console/wiring harness and note original wire routing
• Make secure, insulated connections and route the resistor/leads exactly as original to avoid heat or chafing
• After installation, run a test cycle to ensure proper operation of the affected function

Fix erratic or unresponsive cycle selections with this laundry center rotary encoder switch. Mounts behind the cycle knob to restore accurate settings.

Dryer won't heat or overheating? The temperature switch controls heat settings. DIY-friendly repair—just swap wires and reassemble. Takes 20 minutes.

The Starter is an OEM replacement part for Frigidaire refrigerators. This component is crucial for initiating the compressor, which is responsible for cooling the refrigerator. The starter works by providing the necessary electrical power to get the compressor running, ensuring that the refrigerator maintains the correct temperature.

Causes of a bad starter can include electrical malfunctions, wear and tear over time, or damage from power surges. A faulty starter can prevent the compressor from starting, leading to cooling issues.

Symptoms of a bad Starter include:

• The refrigerator not cooling properly
• The compressor not running or frequently cycling on and off
• Unusual clicking or buzzing noises from the compressor area
• The refrigerator being warmer than usual or food spoiling quickly

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

Washer overfilling or underfilling? The water level pressure switch senses tub pressure to control fill cycles. DIY repair in 20 minutes or less.