Thermistor Parts

Replaced cycling thermostat. Read more

My Electrolux Frigidaire Gas Dryer stopped working and I got an error code E66 that the thermal limiter blew from over heating. The E66 code stops displaying after the initial code and you will then get a door open message. I replaced the thermal limiter and the thermostat just to be sure which part at the problem. The job is hard because you have to take apart the entire dryer and remove the drum. Would be a tough project to complete on your own. Read more

This was a friends dryer. They'd been quoted a $200 call out fee and after taking with them on the phone were also told they could have the dryer taken away for $150. I told my friends that inwould fix it. I used a multimeter to check the thermostats, heaterbelement and funrion dial. I found 2 bad thermostats. I orderd one part from you, another from elsewhere as you did not have stock. I replaced the dead parts with new and the dryer heats again. It cost me $65 total in parts and shipping to... Read more

Removed exterior panels, cleaned all venting, replaced outlet thermistor and thermostat. Pressure washed all removable parts. Reassembled. Now working as it should. Read more

• Won't start
• No heat or not enough heat

Did some dryer repair research (dryer not heating) on the internet. Bought an ohm meter, opened up the dryer and tested the cut-off-T, high limit thermostat, dryer igniter, flame sensor, cycling thermostat for continuity. The igniter was bad, the other parts tested ok. Went online to AppliancePartsPros.com searched for a new igniter for my specific dryer model, found the right replacement igniter and watched the video on how to replace the igniter. Because my dryer is old (15+ years) and I... Read more

Checked vent first to see if there was a blockage. Removed top, front and drum of dryer. Replaced all sensors including flame detection and gas valve coils. Re-assembled and tested. Dryer was now heating Read more

This fridge has had a problem of ice building up around evaporator coil in fresh food side. Wife (she HATES this thing) says it's done this from day one; 10 years. GE guy says all these models do this and there's no fix for it, so we have clean out the ice periodically... Like the 1940s pre auto defrost. Now with the issue of FF side temp too highi assumed the ice had built up around FF evaporator coil preventing proper cooling, but AppliancePartsPros.com suggested the FF temp thermistor may... Read more

Out with the old. In with the new. No problem. Dryers are simple and usually can be fixed quickly. appliance pros makes it easier with their tutorial videos and fast shipping! Read more

So I replaced the hi-temp thermostat and the problem is fixed. Read more

Fridge keept building up ice in defrost drain drain in freezer. Once the drain pan filled with ice it drips into fridge compartment. After taking things apart three times to thaw it out, decided to replace defrost components - heater and temperature switch. In addition to new parts, also added a 12 gauge copper wire hook that hangs from defrost heater into the defrost drain. After this, the defrost cycle is running as expected, but will not know if the issue is corrected until a year or so... Read more

Viewed the video before I purchased the part. Received the part and put it in. Everything went as planned. Read more

Used video and took apart dru, this was extremely helpful. I bypassed the belt and door switch. Tested gas valves (gas disconnected) with multimeter. Found that the igniter worked the first gas valve, but the second gas valve would not open and the igniter would stay on. Found a flow chart online that shows the flame detect turns on causing the gas to turn on and shuts off the igniter. I replaced it and tested again. Igniter turns on, shuts off, then power to the second gas valve turns... Read more

Removed the heater of course and installed the part. Very easy to do no need to remove the drum, just top cover, control panel, and front door assembly. Remove the one screw holding heater, remove blue wire, turn heater CCW to the 8 o'clock poisiton. Install in the reverse order. This is the secound one in a month if it fails again i'll just bypass it and install a 25 AMP fuse. Read more

Realizing that there could be multiple reasons for a gas dryer failing to heat, I decided to test everything I could. The very detailed and product specific video showed me how to disassemble the dryer. The thermostat, cycling thermostat, high limit, flame detector, igniter, gas valve coils and timer all showed correct continuity or resistance. I thought it might be the gas valve itself, but felt that wasn't likely so I decided to go ahead and replace the thermostats and limit switch since... Read more

I was having trouble with my Kenmore Front Load washer. It wouldn't finish the wash cycle...it kept displaying an LE Error code. After I went to Google to help diagnose the problem, which was a bad RPS Sensor, I ordered the part from AppliancePartsPros.com. It literally took about 15-20 mins and with the help of my son-in-law, my washing machine was fixed!! It was going to cost me $85.00 for the Sears repairman to walk in my door, not including parts and labor, and I only paid $27.00... Read more