Dbxr463ed-1W Parts

First, I did a search based on the problem I had with my model of dryer. The model number was on the door frame and was visible when I opened the dryer door. The problem was, when I pressed the button to start a dryer cycle, I heard a clicking noise and the indicator text changed to "Drying", but I could not hear or see the dryer drum turning. The search led me to a page that indicated my problem was usually one of 3 common causes. 1. Faulty door switch 2. Broken Drum drive belt 3. burned out... Read more

We cleaned out all ducts carefully and did other basic troubleshooting but it did not help. Began to research the problem on-line and discovered that this dryer has two heating elements. One can fail while the other continues to provide heat - but with a large impact on drying time. Watched youtube videos and how to take apart the dryer to reach the heating coils. Tested the heating elements for continuity with tester and the outer loop had no continuity indicating it was broken somewhere. ... Read more

We cleaned out all ducts carefully and did other basic troubleshooting but it did not help. Began to research the problem on-line and discovered that this dryer has two heating elements. One can fail while the other continues to provide heat - but with a large impact on drying time. Watched youtube videos and how to take apart the dryer to reach the heating coils. Tested the heating elements for continuity with tester and the outer loop had no continuity indicating it was broken somewhere. ... Read more

• Marks left on clothes
• Noisy

I followed the directions I found on YouTube for removing the front of the dryer. It was fairly easy, with two screws to remove the top and another two to remove the front. Just use a hand Phillips screwdriver, you will have difficulty using a typical power screwdriver due to space limitations. Watch the tabs on the top that engage with the control panel. Push the top to the left to disengage. I broke one of the three. One connector and two fastons needed to be disconnected on the front. ... Read more

• Noisy

Repair went well, replaced the pulley wheel, belt, rear drum bearing. Had an issue after replacement with the dryer stopping after ~5mins or so when running with heat. Fluff cycle would run fine. Details: The lock nut on the pulley wheel didn't feel tight enough so i tried to crimp it back on the pulley arm. It then became way too lose. I had to replace it with a plastic washer I had in my toolkit. That fit snug and seems to work fine. I also added some grease to the pulley shaft under... Read more

Found the entire top bearing support plastic piece was completely worn through, the bearing slides had all disappeared some time ago. So it was obviously the problem. The felt trap duct (which is actually a drum seal along bottom front of drum so I don't know why they call it felt trap duct) had also disappeared, so a lot of lint was getting inside the front panel too. It's a very easy repair to change the bearing support; everything just pops out just like the video shows. Make sure you... Read more

• Doesn't shut off
• Won't start

I watch the video on YouTube. And it went step by step on how to take it off and on Read more

• Will not tumble

Repair went well, replaced the pulley wheel, belt, rear drum bearing. Had an issue after replacement with the dryer stopping after ~5mins or so when running with heat. Fluff cycle would run fine. Details: The lock nut on the pulley wheel didn't feel tight enough so i tried to crimp it back on the pulley arm. It then became way too lose. I had to replace it with a plastic washer I had in my toolkit. That fit snug and seems to work fine. I also added some grease to the pulley shaft under... Read more

Replaced front panel and inner liner of door (kit), trap duct assembly, both bearing slides (gray and white), and drum front support bearing. Procedure is pretty much what one sees in the video clips. Exceptions in our case included: 1. The fact that our door latch¹ was on the front panel while the door strike² was on the door. The newer (replacement) design has the latch on the door and the strike on the front panel! 2. The new door did NOT have the door latch installed (as shown in the... Read more

It was an easy repair just screwed in. The ordering process and simple no hassle and got here fast! I will definitely order from you again Read more

I ordered the new filter on one day and it was delivered the next. Other web sites told me the part was no longer available and I was very surprised and pleased that Appliance Parts Pros had it in stock and shipped it so promptly. Thank you. Read more

I actually called a repair service in our area. The serviceman asked questions and detected that I didn't need a timer unit but thought it was just a knob that was required. He offered to come out but the expense would be considerable. I am SO relieved that it was indeed the knob, and the dryer was fixed. In this time in our lives, every penny counts. I must applaud the serviceman for his honesty and dedication to his trade. He directed me to this website, but also added if there were any... Read more

First symptoms were squeaking drum. This is probably when new glide strips might have been all that we needed. But I put off fixing it... and I put it off some more. Noises got louder, squeaking became screeching, then it started to vibrate loudly. The front drum bearing (really just a plastic arch that the drum rides on) had broken, and with the drum in a canted position, the rear bearing sleeve got messed up too. I ordered the front drum support bearing, and also a rear drum bearing... Read more

• Takes too long to dry

Upon examination of the dryer, I noticed that the belt was intact, though a little worn and hard. However, I noticed that the belt had came of the idler pulley. So I put it back on and had the owners try it out on their next load of wash. It, once again failed to keep the drum turning. So I ordered a new belt and idler pulley (order # 8676164). I found it necessary to remove the drum, in order to change out the new pulley. However, while trying to reinstall the drum, we damaged some of the... Read more

• Won't start

The full story: Dishwasher stopped running mid-cycle. When I first began troubleshooting I tried manually advancing the timer knob, and the machine would run. That led me to believe that the actual timer assembly was bad, so I replaced it. The dishwasher ran fine for a day, and then the same problem came back. This time, however, I also had to push in on the door to get it to run. I looked around online, and someone suggested that the door latch wasn't closing tightly enough. I adjusted the... Read more

• Too hot
• No heat or not enough heat
• Takes too long to dry

Replaced thermal stats Read more