Need Help?
Call
Some parts shown may not be for your model. To see parts for your model only, select it from "Matching Model Numbers" list on the left.
Transfers motor power to rotate the drum. Replace if dryer hums but won't spin or makes squealing sounds. Verify fit with your model number.
Disassembled dryer. Installed new belt, drum rollers, idler arm and blower. Read more
Dryer won't heat or stops heating after 10-15 minutes? Gas valve coils control burner ignition. Simple 5-10 minute repair with video guide included.
Being a complete DIY I hate to call some unknown person into my home knowing that just to get them there will cost me more than I will spend for parts that I don't need.After all, they are trying to make a living and by selling me parts that I don't need will increase their profits. I've dealt with APP before and was impressed by their site because I could find both mechanical and electrical drawings for almost everything I have. I looked up my dryer, decided what was probably the problem,... Read more
Dryer won't start or drum won't turn? A failed motor is often the cause. This motor drives the drum and blower. Moderate DIY repair, 1-2 hours.
Had to replace motor and blower, and both were very easy fixes, both pieces fit just right. The do it yourself videos also helped alot too, so props to them...Thanx alot Read more
Dryer won't start or shuts off mid-cycle? This thermal fuse cuts power when overheating occurs. Common fix for E63, E66 errors. DIY repair under 1 hour.
Replaced exhaust thermal cutoff switch. Sears wanted to charge for a service visit + parts and labor. $17 part, $6 shipping and I received the part the following day. Repair complete in less than an hour at a fraction of the cost. Thanks appliance pros. Read more
Dryer not heating or flame goes out after igniting? This flame sensor monitors burner temperature to regulate gas flow. Easy 15-minute DIY repair.
Dryer making loud rumbling or tapping noise? A worn or damaged blower wheel assembly is often the cause. Moderately difficult repair for most DIYers.
I replaced the Blower Wheel Assembly. Read more
Idler arm assembly mounts near the dryer drum to guide and tension the belt. Replace if the pulley is worn, cracked, or causing belt misalignment issues.
The High Temperature Adhesive is an OEM part for Frigidaire appliances. This adhesive is specifically formulated to withstand high temperatures and is used in various repair applications within appliances such as ovens, ranges, and dryers.The 1-ounce tube contains adhesive formulated to withstand the extreme heat inside dryer drums and cabinets
Causes of a bad adhesive can include exposure to extremely high temperatures over extended periods, contamination by dirt or grease, or the natural aging and drying out of the adhesive.
Symptoms of a bad high temperature adhesive include:
This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.
I'm new to how a dryer works, so I just started taking it apart to see what exactly was causing it. The video examples on the APP website were all amazing. It gave me a good idea of what I was getting into and showed me the common repair issues. The dryer being 12 years old, I was on the fence about repairing or replacing. However, once I got a list of parts I might need and getting the confidence by watching the videos, I said "what have I got to lose." The cause of the scraping and loud... Read more
Supports and guides the dryer drum as it rotates. Replace if the roller is cracked, worn, or causing noise. Sold individually, not pre-assembled.
I ordered a new motor. Read more
Dryer lint filter kit with screen and housing. Replace when clogged, torn, or damaged to maintain airflow and prevent fire hazards. Verify fit by model.
Dryer won't heat or shows E66 error? The thermal limiter prevents overheating by monitoring airflow. Moderate DIY repair, requires rear panel access.
My Electrolux Frigidaire Gas Dryer stopped working and I got an error code E66 that the thermal limiter blew from over heating. The E66 code stops displaying after the initial code and you will then get a door open message. I replaced the thermal limiter and the thermostat just to be sure which part at the problem. The job is hard because you have to take apart the entire dryer and remove the drum. Would be a tough project to complete on your own. Read more
This high limit thermostat is a safety device that monitors the temperature inside the dryer and cuts power to the heating element if the temperature exceeds a safe threshold. It is typically mounted on the heating element housing or exhaust duct. Replace this thermostat if the dryer is not heating at all or if it overheats - a tripped high limit thermostat often indicates a clogged vent or restricted airflow that should also be addressed.
Fixes steam cycle not working or water not entering drum during steam cycles. Controls water flow into dryer. Moderate DIY repair for steam dryers.
This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.
It was easy to find the part on appliance parts pros. Once I found it I studied the diagram and determined that there were 3 screws in the drum that needed to be removed. I disconnected power and then removed 3 interior screws. Once I did that I removed the back cover and removed the single screw on the bottom side of the air duct that held it in place connected to the heat tube. I then reversed disassembly. I want to tell you this is a 2 person job. In order to assemble it you need to... Read more
Idler spring attaches to the idler arm to maintain proper belt tension. Replace if spring is broken, stretched, or missing to restore correct tension.
I encountered a high pitched squeal and loud rumbling. I figured the sounds were likely the rollers despite not matching other sounds on the repair videos for other dryers. The repair video for dryer rollers on AppliancePartsPros.com is of little use until Minute 2:56 because this Electrolux 517 model uses mostly Phillips head screw to fasten the front and top panels in place. You may find one latch at the top front center that holds the top and front panels in place. After unplugging the... Read more
Dryer won't start or stops mid-cycle? This door switch detects when the door is closed, allowing your dryer to run. Simple DIY fix in 15-30 minutes.
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.