Wmh78019hz-1 Parts

After extremely poor support from WhirlpooI and researching numerous U-Tube videos, I fully troubleshot potential failed components and connections. All appeared to function properly, so I reassembled the unit and experienced the same problem as before. I then narrowed down the problem to either the Touchpad ($57+$8 shipping) or the control board ($295+shipping). If those did not work, then a new Microwave of better quality, reliability and support than original microwave, Unfortunately,... Read more

• Exhaust fan not working

Replacing this filter was very easy: two screws hold in the grill cover at the top of the microwave, and then the filter just slides in and out of its holder. There was quite a bit of grease in the area, probably pulled there by the vent from the stove top. I cleaned the grease up and also hand-washed the wire-mesh filter on the bottom of the microwave with soap and warm water. Airflow when running the vent is now noticeably better. Read more

It was a really simple fix, and I kick myself for waiting so long to attempt the repair. Following the YouTube video, I had the old motor out and the new one in in approximately 10 minutes. I even felt the satisfaction of having completed a repair project. Read more

Installed mounting bracket. Redrilled top screw holes. No template for hole locates but plenty of options to make sure you get a stud. Very easy to install. Read more

Ordered from an appliance store and got wrong bulbs. They wanted to charge $15.00 each for the right ones. Your sight had then for $7.00. Read more

I have used appliance parts pros before, their website is easy to use. I typed in the model and serial numbers, of course the number I have is rare, It did not show up on the list of models. It made me a little hesitant to submit the order. All three products came in the same box and on the same date it was promised. Just after opening the package I put everything in the microwave and I was relieved when everything fit perfectly. Read more

It is difficult (if not impossible) to remove the electronic switches from the hard plastic latches. I replaced all three switches and both the upper and lower latches I also replaced the main 20 amp ceramic fuse which blew out when the latch/switches failed. Read more

Watched a You tube video, showed how to remove bottom, unhook wiring, then proceed to top case. Once removed, case is turned upside down so the capture nut can be installed. Part fit perfectly and BAM, done. Case refitted and finished. Part arrived in 2 days. Great service. Read more

Very easy fix. Unplugged microwave, then lowered bottom panel, removed the two leads to the turntable motor, removed two screws attached to motor, removed old motor, put new spacer on motor stem, installed motor with same two screws, reattached the two wires, reattached panel ( after cleaning all the grease that built up over the last 6 years), plugged microwave in and good as new! Took me twenty minutes. Note: the two screws holding the motor were not Phillips like those holding the panel. So... Read more

Bought a new home with microwave venting into kitchen. Ordered damper assembly needed to vent through the wall to the outside. Removed microwave, followed directions in original installation instructions, turned fan over, cut hole in wall, installed wall cap and replaced oven. Problem solved. Read more

Ordered a new one cheaper from you than whirlpool Read more

Replacing a magnetron in my particular 9-year-old microwave (a microwave/hood combination) was not a simple “plug & play” operation. That is why I am placing this in the slightly difficult area. First, it takes 2 people to remove the microwave from the top of the stove. Next the main outer panel need to be removed. After that, 2 sheet metal panels need to be removed in order to expose the high voltage components for testing. Always discharge the high voltage capacitor first before doing... Read more

Replaced door interlocks … and it worked !! Good guess !! Read more

The parts pro I spoke to on the phone was very helpful in ordering the correct parts. I simply installed the ordered parts inside the convection/microwave. They fit perfectly. Read more

When the new bulb didn't want to go in, I felt around and realized the base of the old bulb was still in there. With some effort I got it out and new bulb in, Light cover fit fine, but did not come with a screw to hold it in. That would have been helpful. Read more

Ordered new parts from you and replaced them. Read more